Use and Care Manual

24 25
ninjakitchen.com
ninjakitchen.com
FRANÇAIS
7 When cook time is complete, the unit will
beep and END will appear on the display.
Air Crisp
1 Place cooking pot in the unit with the indent on
the pot aligned with the bump on the main unit.
Place the crisper basket in the pot. Ensure the
splatter shield is in place, then close the hood.
2 Press the AIR CRISP button. The default
temperature setting will display. Use the set
of arrows to the left of the display to adjust
the temperature up to 400°F.
3 Use the set of arrows to the right of the display
to adjust the cook time, in 1-minute increments,
up to 1 hour, or, if using the thermometer, refer to
Using the Foodi™ Smart Thermometer section.
4 Press START/STOP to begin preheating. The
progress bar will begin illuminating. It will
take approximately 3 minutes for the unit to
preheat.
5 When preheating is complete, the unit will beep
and “ADD FOOD” will appear on the display.
6 Open the hood and place ingredients in the
crisper basket. Once the hood is closed,
cooking will begin and the timer will start
counting down.
7 For best results, we recommend shaking
ingredients frequently. When you open the
hood, the unit will pause. Use silicone-tipped
tongs or oven mitts to shake the basket.
When done, replace the basket and close
the
hood . Cooking will automatically resume
after
hood is closed.
8 When cook time is complete, the unit will beep
and END will appear on the display.
NOTE: While preheating is strongly recommended
for best results, you can skip it by pressing
the Skip Preheat Button
. “ADD FOOD” will
appear on the display. Open the hood and
place ingredients in the crisper basket. Once
the hood is closed, cooking will begin and the
timer will start counting down.
NOTE: To check your food’s internal doneness,
press MANUAL for 2 seconds and the food’s
internal temperature will appear on the screen.
Press and hold button again to exit mode.
NOTE: If batch cooking, refer to page 8 for
instructions.
To turn on the unit, plug the power cord into a wall outlet, then press the button.
Roast
1 Place cooking pot in the unit with the indent
on the pot aligned with the bump on the main
unit. Ensure the splatter shield is in place, then
close the hood.
2 Press the ROAST button. The default
temperature setting will display. Use the set
of arrows to the left of the display to adjust
the temperature up to 425°F.
3 Use the set of arrows to the right of the display
to adjust the cook time, in 1-minute increments
up to 1 hour and 5-minute increments from 1 to
4 hours, or, if using the thermometer, refer to the
Using the Foodi Smart Thermometer section.
4 Press START/STOP to begin preheating. The
progress bar will begin illuminating. It will take
approximately 3 minutes for the unit to preheat.
USING THE NINJA® FOODI® SMART XL GRILL – CONT.
5 When preheating is complete, the unit will beep
and “ADD FOOD” will appear on the display.
6 Open the hood and place ingredients in the
pot. Once the hood is closed, cooking will
begin and the timer will start counting down.
7 When cook time is complete, the unit will beep
and END will appear on the display.
NOTE: Convert traditional oven recipes by
reducing the temperature by 25°F. Check food
frequently to avoid overcooking.
NOTE: While preheating is strongly
recommended for best results, you can skip
it by pressing the PREHEAT button. “ADD
FOOD” will appear on the display. Open the
hood and place ingredients in the cooking pot.
Once the hood is closed, cooking will begin
and the timer will start counting down.
NOTE: To use the thermometer just to check your
food’s internal doneness, press MANUAL for 2
seconds and the food’s internal temperature will
appear on the screen. Press and hold button
again to exit mode.
To turn on the unit, plug the power cord into a wall outlet, then press the button.