Multi-Format LCD Rack Mount Monitor ハイエンドラックマウントモニター HDM-2000 Operating Instructions 取扱説明書 Before operating the system, please read this manual thoroughly and remain it for future reference. Volume1, 1st edition Ver.1.
安全上の注意 WARNING この製 品の使用、または使用不 能から生ずる付随的な損害(情報内容の変化・消失、事業利益の損失、事業の 中断など)に関して、当社は責 任を負いかねますのであらかじめご了承ください。 取 扱 説 明 書の記 載内容を守らないことにより生じた損害に関して、当社は責任を負いかねますのであらかじめ ご了承ください。 ご使用の前に、この『 安 全 上の注 意 』をよくお読みのうえ、正しくお使いください。また、お読みに なった後は、大 切に保 管してください。 安 全 上の注 意は、お使いになる人や、他の人への危害、財産への損害を未然に防ぐための内容に なっていますので、必ずお守りください。 表示と図記号の意味は次のようになっています。 警告 取 扱いを誤った場 合 、使用者が死亡または重傷を負うことが想定されること を示します。 ■煙が出ている、変なにおいや音がする等の異常が発生した場合は、電源スイッチを切る! ■本 機を落としたり、強い衝 撃を与えたり、破損した場合は、電源スイッチを切る! ■本 機の内部に水などが入った場 合は、電源スイッチを切る! ■本 機の内部に異 物な
Table of contents HDM-2000 HDM-2000 目次 Names and Functions of Parts 4 各部名称と働き Front panel 4 Rear panel 6 Functions(MENU) 8 前面パネル 背面パネル 機能(メニュー) Connection 14 Setting 19 Outside View & Dimmensions 23 Specifications 24 接続方法 セッティング 外形寸法図 仕様 3
Names and Functions of Parts HDM-2000 HDM-2000 各部名称と働き Front panel 前面パネル Screen The display screen is 7.0 inches diagonal LCD (Active area : 152.4mm 91.4mm). スクリーンは 7.0インチ液晶、画面寸法 152.4mm 91.4mm です。 TALLY indicator Lights up when a tally signal is input to PARALLEL REMOTE connector on the rear panel. 背面の PARALLEL REMOTE コネクタに入力されるタリー信号により点灯します。 POWER switch and POWER Indicator LED Turn on the power supply through the DC IN(12 V) connector. When the power is supplied, the POWER indicator LED lights on.
HDM-2000 HDM-2000 各部名称と働き Front panel 前面パネル USER 1/2/3/4 ( USER ASSIGN Preset Function ) Rotary knobs and indication LEDs Pressing a knob executes the functions, BRIGHT, CONTRAST, SATURATION, and SHARPNESS, assigned to each knob in MENU. When the indication LED lights up, each value of the functions is adjustable from 0 to 100 by rotating. When the LED doesn t light on, each value is set to the default STANDARD value.
HDM-2000 HDM-2000 各部名称と働き Rear panel 背面パネル (Front panel) AUDIO OUT connector (Front panel headphone jack) ( φ 3.5 stereo jack ) Used to output the HD-SDI embedded audio signals selected on the MENU. The audio output channel selection, the volume level adjustment, etc. operate in the MENU. The front panel audio output volume level can be adjusted by MENU right/left button,too.
HDM-2000 HDM-2000 各部名称と働き Rear panel 背面パネル PARALLEL REMOTE ( remote control signal input ) connector (8-pin, RJ-45) Used for the remote control: e.g. for input of the TALLY signal, INPUT signal selection and Preset Function operation. The pin assign, default setting is as the table shows. The control signal is to short-circuit each pin with PIN 5.
HDM-2000 HDM-2000 各部名称と働き [1]MENU Operation メニューの操作について <MENU button> press center 中央 MENU : When pressing MENU center button, MENU items are displayed on the screen. メニュー : MENU ボタン(中央) を押すと メニューが画面上に表示されます。 press up 上 press right 右 press left 左 press down 下 MENU Setting : (1)By pressing down(or up) button select a MENU item displayed on the screen. By pressing center(or right) button confirm the selected item. Then the cursor moves right to setting items.
HDM-2000 HDM-2000 各部名称と働き e.g.
HDM-2000 HDM-2000 各部名称と働き [2]MENU Contents <MENU Item>メニュー項目 INPUT [SDI 1] 入力 PICTURE ピクチャー COLOR [D65/601] 色 メニューの内容(項目および設定値)について <MENU Setting Item>設定項目 <Setting Value>設定値 RETURN INPUT [SDI 1] ANALOG CALIBRATE > SDI 1 SDI 2 OPTION RETURN BRIGHT CONTRAST SATURATION SHARPNESS GAMMA 0/ - - - - - / 100 [50] [80] [50] [0] [2.2] RETURN COLOR MATRIX COLOR TEMP RED BIAS GREEN BIAS BLUE BIAS RED GAIN GREEN GAIN BLUE GAIN [601] [D65] [0] [0] [0] [ 1.00] [ 1.00] [ 1.
HDM-2000 MARKER HDM-2000 各部名称と働き [ON] マーカー RETURN MARKER [OFF] CENTER [ON] ASPECT [OFF] SAFTY [95%] MARKER MAT [CLEAR] LINE THICKNESS [2] LINE TYPE [WHITE] ON / OFF ON / OFF OFF 4:3 16 : 9 1.85 : 1 2.35 : 1 4:3 & 1.85 4:3 & 2.
HDM-2000 HDM-2000 各部名称と働き VECTORSCOPE[ON] ベクトルスコープ RETURN LAYOUT WAVEFORM SIZE POSITION DISP TYPE GAIN [NORMAL] [ON] [MEDIUM] [LEFT BOT] [OVERLAY] [ 1.00] NORMAL LAYOUT A LAYOUT B ON / OFF SMALL MEDIUM LARGE LEFT TOP LEFT BOT RIGHT TOP RIGHT BOT OVERLAY / OVERLAP 1.00/- - - - - / 4.98 ClipGuide [OFF] クリップガイド(ゼブラ) RETURN ClipGuide [OFF] MODE [LUMA&CHROMA] DISP TYPE [ZEBRA] Y UPPER LIMIT [90.0%] Y LOWER LIMIT [0.
HDM-2000 REMOTE リモート SETUP セットアップ HDM-2000 各部名称と働き RETURN PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 [R TALLY] [G TALLY] [B TALLY] [MARKER] [GROUND] [INPUT 1] [INPUT 2] [ASPECT] RETURN FORMAT DISPLAY [AUTO] TIMECODE [OFF] POWER SAVE[ALWAYS ON] KEY LOCK [UNLOCKED] RESET TO MFG DEFAULT > BACKUP USER CONFIG > RESTORE USER CONFIG > AUDIO METER AUDIOPRESET 1/- - - /8 LAYOUT A LAYOUT B WAVEFORM MON VECTORSCOPE ClipGuide TIMECODE LTC TIMECODE VITC1 TIMECODE VITC2 R TALLY G TALLY B TALLY LEFT R TLY LEFT
Connection HDM-2000 HDM-2000 接続方法 Power Supply Connection 電源の接続方法 Make sure to turn off the POWER switches of each unit before connecting. 注意 : 機器を接続する前には、電源スイッチは必ず OFF してください。 1 Connect the DC IN connector( XLR 4-pin) on the rear panel to AC Adaptor supplied. リアパネルのDC IN コネクタにACアダプタ(付属)を接続します。 DC IN(12V) connector XLR 4-pin AC Adaptor(supplied) AC 電源アダプタ(付属) 2 When the POWER switch is turned on and the power is supplied, the POWER Indicator LED lights up and the fans on the rear panel turn.
HDM-2000 HDM-2000 接続方法 HD-SDI Signal Input & Output 1 HD-SDI信号入力および出力 Connect the SDI (HD/SD) (SDI signal input) connector (BNC type) on the rear panel to the HD-SDI output connector of a camera (or VTR, etc.) リアパネルの SDI 1/2 (HD/SD) 入力コネクタ からカメラのHD-SDI output へ接続します。 SDI 1/2 (HD/SD) input connector SDI (HD/SD) OUT (output) connector ( : Loop Thru ) BNC Camera (or VTR, etc.) HD-SDI output 2 By pressing MENU button displayed the MENU and access to INPUT and set to SDI 1 or SDI 2 .
HDM-2000 HDM-2000 接続方法 HD Component / DVI Signal Input 1 HDコンポーネント / DVI 信号入力 Connect the OPTION INPUT connector on the rear panel with the HD component input adaptor(optional) or DVI input adaptor(optional) and connect it to a camera. リアパネルの OPTION INPUT コネクタ に HD コンポーネント入力アダプター(別売) または DVI 入力アダプター(別売) を 接続し、 カメラへ接続します。 OPTION INPUT connector オプション入力 HD component input adaptor ※ Option HD component input adaptor = OC-COMP HDコンポーネント入力アダプター DVI signal input adaptor = OC-DVI Camera (or VTR, etc.
HDM-2000 HDM-2000 接続方法 Audio Signal Output 1 オーディオ信号出力 Connect the AUDIO OUT connector (Stereo Jack, φ 3.5 mm) on the front or rear panel. オーディオ信号をモニター/出力する場合は、 フロントパネルまたはリアパネルの AUDIO OUT コネクタ に接続します。 AUDIO OUT connector オーディオ出力 2 MENU button By pressing MENU button access to AUDIO setting item and set each item to the setting value. The output CHANNEL, VOLUME level, AUDIO LEVEL METER, etc. are adjusted on the MENU. AUDIO LEVEL METER can be assighned to any USER Presets button, F1 - F11.
HDM-2000 HDM-2000 接続方法 Remote Control Setting 1 リモートコントロールの設定 Connect the PARALLEL REMOTE connector on the rear panel with the 8-pin connector with cable. リアパネルの PARALLEL REMOTE コネクタ に 8ピンケーブルを接続します。 PARALLEL REMOTE connector(8-pin, RJ-45) 8-pin connector RJ-45 2 short/open 各端子を接地すると機能が ONします To short-circuit each pin with PIN 5 operates the function : input of the TALLY signal, INPUT signal selection, Function operation ON/OFF, etc.
Pre-Adjustment and Setting HDM-2000 HDM-2000 調整およびセッティング Video Signal Display Adjustment ビデオ画像表示の調整 Each function of the Menus, etc. operates when a signal is input. 注意 : 各機能は、信号が入力されているとき実行,調整ができます。 1 Input signal Setting By pressing MENU button display the MENU and access to INPUT in the MENU and set SDI 1 or SDI 2 . SDI 1/2 and its video format are displayed in the MENU(INFO and INPUT). Or by pressing the preset function button select an input signal.
HDM-2000 HDM-2000 調整およびセッティング Function Setting ファンクションの設定 1 Function Setting By pressing MENU button on the front panel access to the MENU displayed on the screen. Access to any MENU item in the MENU and set each setting item.
HDM-2000 HDM-2000 調整およびセッティング USER ASSIGN of Preset Function ファンクションボタンの設定 1 Function Setting By pressing MENU button(center) on the front panel access to the MENU displayed on the screen. Access to any MENU item in the MENU and set each setting item.
HDM-2000 HDM-2000 調整およびセッティング AUDIO オーディオの設定・調整 1 AUDIO Function Setting By pressing MENU button(center) on the front panel access to the MENU displayed on the screen. Access to AUDIO in the MENU and set each setting item.
Outside View & Dimmensions HDM-2000 外形寸法図 HDM-2000 36.7 57.2 132.6 (3U) 449 465 480.8 2.3 26 71 60.
Specifications HDM-2000 仕様 HDM-2000 画像 Display LCD Panel TFT-LCD Active Matrix (TN) Size 7.0 inch diagonal ( 152.4(H) x 91.4(V) mm ) Aspect Ratio 16 : 9 (16 : 10) Resolution 800(H) x 480(V) x 3(RGB). Effective Pixels 解像度 Viewing Angle 130 (H), 110 (V) 視野角 Color 16.
HDM-2000 Operating Instructions