FOREWORD READ FIRST—THEN DRIVE SAFELY Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. Before driving your vehicle please read this Owner’s Manual carefully. This will ensure familiarity with controls and maintenance requirements, assisting you in the safe operation of your vehicle.
WHEN READING THE MANUAL CALIFORNIA PROPOSITION 65 WARNING This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle. WARNING All information, specifications and illustrations in this manual are those in effect at the time of printing. NISSAN reserves the right to change specifications or design without notice and without obligation.
BLUETOOTHt is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Xanavi Informatics Corporation. © 2006 NISSAN NORTH AMERICA, INC. All rights reserved. No part of this Owner’s Manual may be reproduced or stored in a retrieval system, or transmitted in any form, or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Nissan North America, Inc.
NISSAN CUSTOMER CARE PROGRAM NISSAN CARES . . . Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs.
Table of Contents Illustrated table of contents 0 Safety—Seats, seat belts and supplemental restraint system 1 Instruments and controls 2 Pre-driving checks and adjustments 3 Monitor, climate, audio, phone and voice recognition systems 4 Starting and driving 5 In case of emergency 6 Appearance and care 7 Maintenance and do-it-yourself 8 Technical and consumer information 9 Index 10
Z REVIEW COPY—2007 Altima (alt) Owners Manual—USA_English (nna) 10/26/06—debbie X
0 Illustrated table of contents Airbags, seat belts and child restraints . . . . . . . . . . . . . . . 0-2 Exterior front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-3 Exterior rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-4 Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5 Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-6 Engine compartment check locations . . . .
AIRBAGS, SEAT BELTS AND CHILD RESTRAINTS 1. 2. 3. Top tether strap anchor (P. 1-20) Rear seat belts (P. 1-9) Supplemental curtain side-impact air bags (P. 1-35) 4. Supplemental side-impact air bags (P. 1-35) 5. Front head restraint (P. 1-7, P. 1-8) 6. Front seat belts (P. 1-9) 7. Supplemental front-impact air bags (P. 1-35) 8. Seats (P. 1-2) 9. Occupant classification sensor (pattern sensor) (P.1-42) 10. Seat belt pretensioners (P. 1-48) 11. LATCH (Lower Anchors and Tethers for CHildren) (P.
EXTERIOR FRONT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Power windows (P. 2-41) Windshield (P. 8-19) Windshield wiper and washer switch (P. 2-25) Engine hood (P. 3-17) Tie down/towing hooks (P. 6-12) Fog light switch (if so equipped) (P. 2-31) Headlight and turn signal switch (P. 2-26) Replacing bulbs (P. 8-26) Tire pressure (P. 8-31) Flat tire (P. 6-2) Tire chains (P. 8-38) Mirrors (P. 3-22) Door locks, Intelligent key system, keys, request button (P.
EXTERIOR REAR 1. 2. 3. 4. 5. 6. 7. 8. 9. Rear window defroster switch (P. 2-26) Interior trunk lid release (P. 3-18) Trunk lid (P. 3-17) Vehicle loading (P.9-12) Exterior trunk lid release/request button (P.3-12 Replacing bulbs (P. 8-26) Fuel-filler cap, fuel recommendation (P. 3-19, P. 9-3) Fuel-filler door (P. 3-19) Child safety locks (P.
PASSENGER COMPARTMENT 1. 2. 3. 4. 5. 6. Interior trunk access (P. 1-5) Sunroof (if so equipped) (P. 2-44) Sun visors (P. 3-21) Interior lights, illuminated entry (P. 2-45) HomeLinkT (if so equipped) (P. 2-47) Automatic anti-glare inside mirror (if so equipped) (P. 3-22) 7. Glove box (P. 2-38) 8. Front cup holders (P. 2-37) 9. Front console (P. 2-38) 10. Front seat (P. 1-2) 11. Rear seat (P. 1-5) See the page number indicated in parentheses for operating details.
INSTRUMENT PANEL 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. LIC1055 1. 2. 3. Driver, center and passenger ventilators (P. 4-9) Headlight/fog light (if so equipped)/turn signal switch (P. 2-26) Steering wheel switch for audio control (if so equipped) (P. 4-43) 4. 5. 6. Meters and gauges (P. 2-3) Driver supplemental air bag/horn (P. 1-35, 2-32) Cruise control main/set switch (if so equipped) (P. 5-17) 19. 20. Windshield wiper/washer switch (P. 2-25) Push Button Ignition (P.
ENGINE COMPARTMENT CHECK LOCATIONS QR25DE engine 1. 2. 3. Power steering fluid reservoir (P. 8-13) Engine oil filler cap (P. 8-9) Brake fluid reservoir/Clutch fluid reservoir (M/T model) (P. 8-13, 8-14) 4. Air cleaner (P. 8-18) 5. Fuse block (P. 8-21) 6. Battery (P. 8-15) 7. Fuse/fusible link box (P. 8-21) 8. Engine oil dipstick (P. 8-9) 9. Radiator cap (P. 8-8) 10. Drive belt location (P.8-16) 11. Engine coolant reservoir (P. 8-8) 12. Windshield washer fluid reservoir (P.
VQ35DE engine 1. 2. 3. Power steering fluid reservoir (P. 8-13) Engine oil filler cap (P. 8-9) Brake fluid reservoir/Clutch fluid reservoir (M/T model) (P. 8-13, 8-14) 4. Air cleaner (P. 8-18) 5. Fuse block (P. 8-21) 6. Battery (P. 8-15) 7. Fuse/fusible link box (P. 8-21) 8. Engine oil dipstick (P. 8-9) 9. Radiator cap (P. 8-8) 10. Drive belt location (P.8-16) 11. Engine coolant reservoir (P. 8-8) 12. Windshield washer fluid reservoir (P.
WARNING/INDICATOR LIGHTS Warning light or Name Page Anti-lock Braking System (ABS) warning light (if so equipped) 2-9 Automatic transmission check warning light (if so equipped) 2-10 Brake warning light 2-10 Charge warning light 2-10 Engine oil pressure warning light 2-10 Intelligent Key system warning light 2-11 Low tire pressure warning light 2-11 or Warning light Indicator light Name Page Indicator light Name Page Master warning light 2-12 Security indicator light 2-24 Seat
MEMO 0-10 Illustrated table of contents
1 Safety—Seats, seat belts and supplemental restraint system Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front manual seat adjustment . . . . . . . . . . . . . . . . . . . . 1-2 Front power seat adjustment (if so equipped for driver’s seat) . . . . . . . . . . . . . . . . . . 1-4 Folding rear seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Head restraint adjustment . . . . . . . . . . . . . . . . . . . . . . .
SEATS FRONT MANUAL SEAT ADJUSTMENT ARS1152 WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. ● For the most effective protection when the vehicle is in motion, the seat should be upright.
WRS0738 WRS0739 Forward and backward Reclining Pull the lever up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. To recline the seatback, pull the lever up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position.
belt fit (see “Precautions on seat belt usage” later in this section). Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped. WRS0751 FRONT POWER SEAT ADJUSTMENT (if so equipped for driver’s seat) Operating tips ● The power seat motor has an auto-reset overload protection circuit. If the motor stops during operation, wait 30 seconds, then reactivate the switch. ● Do not operate the power seat switch for a long period of time when the engine is off.
WRS0752 WRS0743 Seat lifter (if so equipped for driver’s seat) Lumbar support (if so equipped for driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion. The lumbar support feature provides lower back support to the driver. Move the switch forward or backward to adjust the seatback lumbar area.
1 s 2 s Open access cover on rear parcel shelf. 3 s Fold down the passenger side seatback. Push down on the button on the rear parcel shelf. WARNING ● Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold-down position. Use of these areas by passengers without proper restraints could result in serious injury in an accident or sudden stop.
WRS0167 LRS0746 Center armrest HEAD RESTRAINT ADJUSTMENT Pull the armrest down until it is horizontal. To raise the head restraint, pull it up. To lower, push and hold the lock knob and push the head restraint down. WRS0134 Adjust the head restraint so the center is level with the center of your ears. WARNING Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Do not remove them. Check the adjustment after someone else uses the seat.
● Do not attach anything to the head restraint stalks. Doing so could impair active head restraint function. The Active Head Restraint moves forward utilizing the force that the seatback receives from the occupant in a rear-end collision. The movement of the head restraint helps support the occupant’s head by reducing its backward movement and helping absorb some of the forces that may lead to whiplash type injuries.
SEAT BELTS SSS0136 PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly adjusted and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes a supplemental air bag. Most U.S.
SSS0134 WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained in the rear seat and, if appropriate, in a child restraint. SSS0016 WARNING ● The seat belt should be properly adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly.
● Be sure the seat belt tongue is securely fastened to the proper buckle. ● Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness. ● Do not allow more than one person to use the same seat belt. ● Never carry more people in the vehicle than there are seat belts. SSS0014 WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck.
There are three basic types of child restraint systems: ● Rear facing child restraint ● Front facing child restraint ● Booster seat The proper restraint depends on the child’s size. Generally, infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints. Front facing child restraints are available for children who outgrow rear facing child restraints and are at least 1 year old.
have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat. WARNING Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident or sudden stop.
fully retracted. Once retracted, the seat belt is in the emergency locking mode. See “Child restraints” later in this section for more information. The automatic locking mode should be used only for child restraint installation. During normal seat belt use by a passenger, the locking mode should not be activated. If it is activated it may cause uncomfortable seat belt tension.
● Grasp the shoulder belt and pull forward quickly. The retractor should lock and restrict further belt movement. If the retractor does not lock during this check or if you have any questions about seat belt operation, see a NISSAN dealer. WRS0139 Unfastening the seat belts s 1 To unfasten the seat belt, press the button on the buckle. The seat belt automatically retracts.
CHILD RESTRAINTS WARNING ● After adjustment, release the adjustment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position. ● The shoulder belt anchor height should be adjusted to the position best for you. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident.
● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An inflating supplemental front air bag could seriously injure or kill your child. A rearfacing child restraint must only be used in the rear seat. WRS0256 WARNING ● Infants and small children should always be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can result in serious injury or death.
● When your child restraint is not in use, keep it secured with the LATCH System or a seat belt to prevent it from being thrown around in case of a sudden stop or accident. CAUTION Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint. This vehicle is equipped with a universal child restraint lower anchor system, referred to as the Lower Anchors and Tethers for CHildren System or LATCH.
● Do not secure a child restraint in the center rear seating position using the LATCH anchors. The child restraint will not be secured properly. ● Child restraint anchor points are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstance are they to be used for adult seat belts or harnesses. LRS0660 LATCH lower anchor location LATCH lower anchor point locations The LATCH anchors are located at the rear of the seat cushion near the seatback.
TOP TETHER STRAP CHILD RESTRAINT If the manufacturer of your child restraint requires the use of a top tether strap, it must be secured to the anchor point. WARNING Child restraint anchor points are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts or harnesses. LRS0662 LATCH rigid-mounted attachment LATCH child restraints generally require the use of a top tether strap.
Installing top tether strap First, secure the child restraint with the seat belt or LATCH System (rear outboard seat positions only), as applicable. 1. Flip up the anchor cover from the anchor point which is located directly behind the child seat. 2. Position the top tether strap over the top of the seatback. 3. Secure the tether strap to the tether anchor bracket that provides the straightest installation. 4. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.
LRS0663 Front facing web-mounted – step 2 2. Secure the child restraint anchor attachments to the LATCH lower anchors. 3. The back of the child restraint should be secured against the vehicle seatback. If the seating position does not have an adjustable head restraint and it is interfering with the proper child restraint fit, try another seating position or a different child restraint. LRS0664 LRS0671 Front facing rigid-mounted – step 2 Front facing – step 4 4.
WRS0697 Front facing – step 6 7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 3 through 6. Rear-facing Follow these steps to install a rear-facing child restraint using LATCH System: LRS0665 Rear facing web-mounted – step 2 2. Secure the child restraint anchor attachments to the LATCH lower anchors. LRS0666 Rear facing rigid-mounted – step 2 3.
LRS0673 Rear facing – step 3 4. Before placing the child in the child restraint, hold the child restraint near the LATCH attachment and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the anchor attachments to further tighten the child restraint.
2. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions ● NISSAN recommends that child restraints be installed in the rear seat. However, if you must install a forward facing child restraint in the front passenger seat, move the passenger seat to the rearmost position. Also, be sure the front passenger air bag status light is illuminated to indicate the passenger air bag is OFF.
WRS0680 Front facing – step 3 3. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing. LRS0667 Front facing – step 4 4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts to emergency locking mode when the seat belt is fully retracted.
8. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the shoulder belt to further tighten the child restraint.
WRS0475 Front facing – step 11 11. If the child restraint is installed in the front passenger seat, push the ignition switch to the ON position. The front passenger air bag status light should illuminate. If this light is not illuminated see 9Front passenger air bag and status light9 in this section. Move the child restraint to another seating position. Have the system checked by a NISSAN dealer.
LRS0669 Rear facing – step 3 3. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the automatic locking mode (child restraint mode). It reverts to emergency locking mode when the seat belt is fully retracted. LRS0670 Rear facing – step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0762 Rear facing – step 5 5.
BOOSTER SEATS 7. Check that the retractor is in the automatic locking mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retractor is in the automatic locking mode 8. Check to make sure that the child restraint is properly secured prior to each use. If the belt is not locked, repeat steps 3 through 7.
● Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle. Also, do not put the same seat belt around both your child and yourself. ● NISSAN recommends that the booster seat be installed in the rear seat. According to accident statistics, children are safer when properly restrained in the rear seat than in the front seat.
LRS0455 LRS0453 LRS0464 Booster seats of various sizes are offered by several manufacturers. When selecting any booster seat, keep the following points in mind: 1 is chosen, the low back booster seat s vehicle seat back must be at or above the center of the child’s ears. If the seat back is lower than the center of the child’s ears, a 2 should be used. high back booster seat s children be restrained in an approved child restraint at all times while the vehicle is being operated.
BOOSTER SEAT INSTALLATION WARNING NISSAN recommends that booster seats be installed in the rear seat. However, if you must install a booster seat in the front passenger seat, move the passenger’s seat to the rearmost position. CAUTION Do not use the lap/shoulder belt automatic locking mode when using a booster seat with the seat belts. Follow these steps to install a booster seat in the rear seat or in the front passenger seat: LRS0451 WRS0699 1.
4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to follow the booster seat manufacturer’s instructions for adjusting the belt routing. 5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack. Be sure the shoulder belt is positioned across the top, middle portion of the child’s shoulder. Be sure to follow the booster seat manufacturer’s instructions for adjusting the belt routing. LRS0452 Rear outboard position 3.
SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System (SRS) section contains important information concerning the driver and passenger supplemental front air bags (NISSAN Advanced Air Bag System), supplemental side air bags, curtain side-impact air bags and pre-tensioner seat belts. WRS0475 7. If the booster seat is installed in the front passenger seat, push the ignition switch to the ON position.
seatback and as far away as practical from the steering wheel or instrument panel. Always use the seat belts. ● The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The advanced air bag system monitors the severity of a collision and seat belt usage then inflates the air bags. Failure to properly wear seat belts can increase the risk or severity of injury in an accident.
ARS1133 ARS1041 WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.
ARS1042 ARS1043 1-38 Safety—Seats, seat belts and supplemental restraint system Z REVIEW COPY—2007 Altima (alt) Owners Manual—USA_English (nna) 10/26/06—debbie X ARS1044
● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An inflating supplemental front air bag could seriously injure or kill your child. See “Child restraints” earlier in this section for details. ARS1045 ARS1046 WARNING ● Children may be severely injured or killed when the supplemental front air bags, side air bags or curtain sideimpact air bags inflate if they are not properly restrained.
WARNING SSS0101 WARNING Supplemental side air bag and curtain side-impact air bag (if so equipped): SSS0188 ● The seat belts, the supplemental side air bags and curtain side-impact air bags are most effective when you are sitting well back and upright in the seat with both feet on the floor. The side air bag and curtain side-impact air bag inflate with great force.
WRS0032 SSS0159 SSS0162 WARNING ● When sitting in the rear seat, do not hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially careful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations. ● Do not use seat covers on the front seatbacks. They may interfere with supplemental side air bag inflation.
1. SRS curtain side-impact air bag modules 2. SRS curtain side-impact air bags 3. Supplemental side air bag modules 4. Diagnosis sensor unit 5. Supplemental front air bag modules 6. Crash zone sensor 7. Seat belt buckle switches on driver’s and passenger’s side 8. Occupant classification sensor (pattern sensor) 9. Occupant classification system control unit 10. Seat belt pre-tensioner retractor 11. Side satellite sensor 12.
The driver supplemental front air bag is located in the center of the steering wheel. The passenger supplemental front air bag is mounted in the dashboard above the glove box. The supplemental front air bags are designed to inflate in higher severity frontal collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions.
Status light is The front passenger air bag status light located on the instrument panel above the radio controls. The light operates as follows: ● Unoccupied passenger’s seat: The is OFF and the front passenger air bag is OFF and will not inflate in a crash. ● Passenger’s seat occupied by a small adult, child or child restraint as outlined in this illuminates to indicate section: The that the front passenger air bag is OFF and will not inflate in a crash.
restraints and booster seats be properly installed in a rear seat. If this is not possible, the occupant classification sensor is designed to operate as described above to turn the front passenger air bag OFF for specified child restraints as required by the regulations. Failing to properly secure child restraints and to use the automatic locking mode (child restraint mode) may allow the restraint to tip or move in an accident or sudden stop.
● Do not place objects with sharp edges on the seat. Also, do not place heavy objects on the seat that will leave permanent impressions in the seat. Such objects can damage the seat or occupant classification sensor (pattern sensor). This can affect the operation of the air bag system and result in serious personal injury. ● Do not use water or acidic cleaners (hot steam cleaners) on the seat. This can damage the seat or occupant classification sensor.
to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions. Vehicle damage (or lack of it) is not always an indication of proper supplemental side air bag and curtain side-impact air bag operation. LRS0259 Supplemental side-impact air bag and curtain side-impact air bags system The supplemental side-impact air bags are located in the outside of the seatback of the front seats.
WARNING ● Do not place any objects near the seatback of the front seats. Also, do not place any objects (an umbrella, bag, etc.) between the front door finisher and the front seat. Such objects may become dangerous projectiles and cause injury if the supplemental side air bag inflates. ● Right after inflation, several side air bag and curtain side-impact air bag system components will be hot. Do not touch them; you may severely burn yourself.
● Work around and on the pre-tensioner system should be done by a NISSAN dealer. Installation of electrical equipment should also be done by a NISSAN dealer. Unauthorized electrical test equipment and probing devices should not be used on the pre-tensioner seat belt system. ● If you need to dispose of the pretensioner or scrap the vehicle, contact a NISSAN dealer. Correct pre-tensioner disposal procedures are set forth in the appropriate NISSAN Service Manual.
When the ignition is in the ON position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the supplemental front air bag, supplemental side air bag and curtain side-impact air bag and pretensioner seat belt systems need servicing: ● The supplemental air bag warning light remains on after approximately 7 seconds. ● The supplemental air bag warning light flashes intermittently.
WARNING ● Once a supplemental front air bag, supplemental side air bag or curtain side-impact air bag has inflated, the air bag module will not function again and must be replaced. Additionally, if any of the supplemental front air bags inflate, the activated pre-tensioner seat belts must also be replaced. The air bag module and pre-tensioner seat belt system should be replaced by a NISSAN dealer. The air bag module and pre-tensioner seat belt system cannot be repaired.
2 Instruments and controls Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-3 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Engine coolant temperature gauge . . . . . . . . . . . . . . . 2-4 Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cargo net (if so equipped). . . . . . . . . . . . . . . . . . . . . . 2-40 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41 Power windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41 Sunroof (if so equipped). . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44 Automatic sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44 Interior light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. LIC1055 1. 2. 3. Driver, center and passenger ventilators (P. 4-9) Headlight/fog light (if so equipped)/turn signal switch (P. 2-26) Steering wheel switch for audio control (if so equipped) (P. 4-43) 4. 5. 6. Meters and gauges (P. 2-3) Driver supplemental air bag/horn (P. 1-35, 2-32) Cruise control main/set switch (if so equipped) (P. 5-17) 19. 20. Windshield wiper/washer switch (P. 2-25) Push Button Ignition (P.
METERS AND GAUGES LIC1057 SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h). LIC1056 1. 2. 3. 4. 5. Tachometer Speedometer Fuel gauge Engine coolant temperature gauge Odometer/twin trip odometer/trip computer 6. Vehicle Information Display Odometer/Twin trip odometer The odometer/twin trip odometer is displayed when the ignition key is in the ON position.
WIC1067 LIC1058 Changing the display: TACHOMETER For vehicles equipped with trip computer, pushing the change button changes the display as follows: The tachometer indicates engine speed in revolutions per minute (rpm). Do not rev engine into 1 . the red zone s Trip → Trip → Trip For vehicles with navigation system, refer to “How to use the ’trip’ button” in the “Display screen, heater, air conditioner and audio systems” section later in this manual.
indicates that the fuel-filler door is The located on the driver’s side of the vehicle. CAUTION If the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” in the “In case of emergency” section for immediate action required.
COMPASS DISPLAY (if so equipped) This unit measures terrestrial magnetism and indicates the direction of the vehicle’s heading. You can also calibrate the compass by driving your vehicle on your everyday route. The compass will be calibrated once it has tracked three complete circles. With the ignition switch in the ON position, press the button as described in the chart below to activate various features of the automatic antiglare rearview mirror.
Once the desired zone number is displayed, stop pressing the MODE button and the display will show compass direction within a few seconds. NOTE: Use zone number 5 for Hawaii.
● If a magnet is located near the compass or the vehicle is driven where the terrestrial magnetism is disturbed, the compass display may not indicate the correct direction. to the correct compass point when the vehicle moves to an area where the geomagnetism is stabilized.) ● In places where the terrestrial magnetism is disturbed, the correction of the direction starts automatically. ● Do not install a ski rack, antenna, etc., which are attached to the vehicle by means of a magnet.
WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS or Anti-lock Braking System (ABS) warning light (if so equipped) Slip indicator light (if so equipped) Automatic transmission check warning light (if so equipped) Seat belt warning light and chime or Supplemental air bag warning light Brake warning light Security indicator light Traction control system off indicator light (if so equipped) Charge warning light Continuously Variable Transmission (CVT) position indicator light (if so equipped) Turn sig
If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock function is turned off. The brake system then operates normally, but without anti-lock assistance. See 9Brake system9 in the 9Starting and driving9 section.
dipstick to check the oil level. See “Engine oil” in the “Maintenance and do-it-yourself” section of this manual. CAUTION Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not covered by warranty. Turn off the engine as soon as it is safe to do so.
● If the light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF.
Unless checked and repaired, the supplemental restraint system (air bag system) and/or the pretensioner seat belts may not function properly. For additional details see “Supplemental restraint system” in the “Safety—Seats, seat belts and supplemental restraint system” section of this manual.
● Malfunction indicator light blinking — An engine misfire has been detected which may damage the emission control system. To reduce or avoid emission control system damage: – do not drive at speeds above 45 MPH (72 km/h). – avoid hard acceleration or deceleration. – avoid steep uphill grades. – if possible, reduce the amount of cargo being hauled or towed. The malfunction indicator light may stop blinking and come on steady. Have the vehicle inspected by a NISSAN dealer.
VEHICLE INFORMATION DISPLAY 2 seconds if the system is operational. If the light stays on or comes on along with the SLIP indicator light while you are driving, have the vehicle dynamic control system checked by a NISSAN dealer. While the vehicle dynamic control system is operating, you might feel slight vibration or hear the system working when starting the vehicle or accelerating, but this is normal.
For more information about this indicator see the “Vehicle Information Display indicator lights and warnings” section later in this chapter. LIC1103 HOW TO USE THE VEHICLE INFORMATION DISPLAY When the button, located on the instrument panel just behind the steering wheel is pressed, the following modes will display on the screen.
LIC1044 LIC1046 LIC1045 Alert mode Reset mode Maintenance mode The alert mode allows you to set alerts notifying of time to rest or icy conditions. The reset mode can be selected in any screen that allows for preferences to be programmed. Once the screen is selected, you have the option to reset their selected distances or time to a new setting.
LIC1047 LIC1098 LIC1093 Display mode Warning mode Fuel Economy mode The LANGUAGE/UNIT screen will appear when selecting the “Language/Unit” key and pressing . The warning mode can be selected to view any warnings that may be present. Once the screen is selected you have the option of skipping the warning or viewing it in detail. The fuel economy mode can be selected to display the average fuel economy since the last reset.
LIC1097 LIC1095 LIC1096 Average speed mode Range mode Exterior Temperature mode The average speed mode can be selected how to display the average miles per gallon and miles per hour since the last reset. The range mode can be selected to give you an estimation of the distance that can be driven before refueling. The range is constantly calculated based on the amount of fuel in the fuel tank and the actual fuel consumption.
LIC1042 Vehicle Information Display indicator lights and warnings 4. Low windshield washer fluid warning 8. Cruise main switch indicator 5. No key warning 9. Cruise set switch indicator 1. Door ajar warning 6. Parking brake indicator 2. Lock warning 7. Shift “P” warning 10. Engine start operation indicator (automatic transmission) 3.
11. Engine start operation indicator (manual transmission) 12. Intelligent key insertion indicator 13. Intelligent key removal indicator 14. Intelligent key battery discharge indicator 15. Steering lock release malfunction indicator 16. Engine off indicator Low fuel warning light This light comes on when the fuel level in the fuel tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty).
main switch is pushed again. When the cruise main switch indicator light comes on, the cruise control system is operational. This indicator means that the engine will start by pushing the push-button ignition switch with the clutch and the brake pedal depressed. Cruise set switch indicator light Intelligent Key insertion indicator The light comes on while the vehicle speed is controlled by the cruise control system.
SECURITY SYSTEMS The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.
Vehicle security system activation The vehicle security system will give the following alarm: ● The headlights blink and the horn sounds intermittently. ● The alarm automatically turns off after approximately 50 seconds. However, the alarm reactivates if the vehicle is tampered with again. The alarm can be shut off by unlocking the driver’s door or trunk lid with the key, or by pressing the button on the intelligent key.
WINDSHIELD WIPER AND WASHER SWITCH 2 s 3 s Low — continuous low speed operation High — continuous high speed operation 4 to have one sweep operaPush the lever up s tion of the wiper. 5 to operate the Pull the lever toward you s washer. The wiper will also operate several times. ● Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank.
REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH HEADLIGHT AND TURN SIGNAL SWITCH NOTE: The top few rows of wires on the rear window are not part of the rear window defroster system. These wires make up the antenna for the audio system. XENON HEADLIGHTS (if so equipped) WARNING cHIGH VOLTAGE ● When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer.
(for example, when the vehicle stops at a traffic signal). Even when the daytime running lights are active (Canada only), the xenon headlights do not turn on. This way the life of the xenon headlights is not reduced. ● If the xenon headlight bulb is close to burning out, the brightness will drastically decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above signs appear, contact a NISSAN dealer.
NOTE: Autolight activation sensitivity and the time delay for autolight shutoff is adjustable for vehicles with navigation system. See “Vehicle electronic systems” in the “Display screen, heater, air conditioner and audio systems” section later in this manual. To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi1 . tion s 2. Turn the ignition key to ON.
CAUTION Even though the battery saver feature automatically turns off the headlights after a period of time, you should turn the headlight switch to the OFF position when the engine is not running to avoid discharging the vehicle battery. DAYTIME RUNNING LIGHT SYSTEM (Canada only) LIC1068 Be sure you do not put anything on top of 1 located on the top the autolight sensor s side of the instrument panel.
WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others. LIC1066 LIC1088 INSTRUMENT BRIGHTNESS CONTROL TURN SIGNAL SWITCH The instrument cluster illuminates when the ignition switch is in ON position. 1 s The instrument brightness control operates when the headlight control switch is in the AUTO, or position.
HAZARD WARNING FLASHER SWITCH The headlights must be on and the low beams selected for the fog lights to operate. The fog lights automatically turn off when the high beam headlights are selected. LIC1089 FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the position.
HORN HEATED SEAT (if so equipped) ● Turn signals do not work when the hazard warning flasher lights are on. The flashers will operate with the ignition switch in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving. LIC1069 LIC0136 To sound the horn, push the center pad area of the steering wheel. The front seats are warmed by built-in heaters (if so equipped). The switches are located on the center console. WARNING Do not disassemble the horn.
TRACTION CONTROL SYSTEM (TCS) OFF SWITCH (if so equipped) 3. When the seat is warmed or before you leave the vehicle, be sure to turn the switch off. ● The battery could run down if the seat heater is operated while the engine is not running. CAUTION ● Do not use the seat heater for extended periods or when no one is using the seat. ● Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped) POWER OUTLET LIC1070 WIC0534 The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driving conditions. If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off.
STORAGE ● When not in use, be sure to close the cap. Do not allow water to contact the outlet. ● Do not leave devices plugged in the outlet for an extended period of time because the constant supply of power will drain the battery WIC1119 Console LIC1073 MAP POCKETS ● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on. ● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF. ● Push the plug in as far as it will go.
CAUTION ● Do not use for anything other than sunglasses. ● Do not leave sunglasses in the sunglasses holder while parking in direct sunlight. The heat may damage the sunglasses. LIC0016 LIC1074 SEATBACK POCKETS SUNGLASSES HOLDER The seatback pockets are located on the back of the driver’s and passenger’s seats. The pockets can be used to store maps. To open the sunglasses holder, push and release. Only store one pair of sunglasses in the holder.
LIC1075 Front - Type A CUP HOLDERS To open the front cup holders, push the cup holder lid. To close, lower the cup holder lid and push down until it clicks in place. The plastic insert may be removed to accommodate a larger cup size or for cleaning. The rear cup holders are located in the fold-down armrest in the rear seat back. LIC1105 Front - Type B WRS0167 Rear CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink.
To route a phone cord to the power outlet: 1. Open the upper half of the console box. 2. Remove the felt mat, and then remove the cutout area from the mat. 3. Remove the access hole cover. 4. Install the felt mat. 5. Route the phone cord through the access hole and plug into the power outlet. WIC1076 WIC1120 GLOVE BOX CONSOLE BOX Open the glove box by pulling the handle. When 1 or unlocking s 2 the glove box, use the locking s master key.
LIC1090 WIC1121 Lower half Pull up on the passenger’s side latch to open the lower half of the console box. A power outlet is located inside the console box and there is storage for compact discs. Type A LIC1078 Type B COVERED STORAGE BOX Push the center of the lid to open.
LIC0748 GROCERY HOOKS (if so equipped) The grocery hooks are located in the trunk and can be used to hang a standard size plastic grocery bag. CAUTION Do not apply a total load of more than 20 lbs (9 kg) to a single grocery hook. LIC1079 CARGO NET (if so equipped) WARNING The cargo net helps keep packages in the cargo area from moving around while the vehicle is in motion. ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting.
WINDOWS POWER WINDOWS WARNING ● Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. LIC0802 To install the cargo net, attach the net to the retainers. To remove the cargo net, detach the net from the cargo net retainers. ● Do not leave children unattended inside the vehicle. They could unknowingly activate switches or controls and become trapped in a window.
Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close all of the windows. To open a window, push the switch to the first detent and continue to hold down until the desired window position is reached. To close a window, pull the switch to the first detent and continue to hold down until the desired window position is reached. WIC1092 Front passenger’s power window switch The passenger’s window switch operates only the corresponding passenger’s window.
Auto-reverse function 1. Push the ignition switch to the ON position. If the control unit detects something caught in the window as it is closing, the window will be immediately lowered. 2. Open the window more than halfway by operating the power window switch. The auto-reverse function can be activated when the window is closed by automatic operation when the ignition switch is in the ON position or for 45 seconds after the ignition switch is turned to the OFF position.
SUNROOF (if so equipped) To open or close the sunroof part way, push the switch in any direction while the sunroof is sliding to stop it in the desired position. Tilting the sunroof Close the sunroof by pushing the switch 2 . Release the switch, then push toward s 2 again to tilt the sunthe switch toward s roof up. To tilt the sunroof down, push the switch 1 . toward s WARNING LIC1082 AUTOMATIC SUNROOF The sunroof will only operate when the ignition switch is in the ON position.
INTERIOR LIGHT 5. Within 5 seconds of completing step 4, . After a press and continuously hold delay of 5 seconds, the panel will move from the tilt position to the open position and back to the close position. The lights will go off when the ignition switch is in the ON position, or the driver’s door is closed and locked. 6. Release . Do not disconnect the power for at least 2 seconds. The sunroof is now restarted.
MAP LIGHTS TRUNK LIGHT The light illuminates when the trunk lid is opened. When the trunk lid is closed, the light goes off. The light will go off after about 30 minutes if the trunk lid is left open, unless the ignition switch is in the ACC or ON position. For bulb replacement procedures, refer to “Exterior and interior lights” in the “Maintenance and do-it-yourself” section of this manual. LIC1080 Front map lamps To turn the map lights on, press the light lens. To turn them off, press the lens again.
HOMELINKT UNIVERSAL TRANSCEIVER (if so equipped) The HomeLinkT Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems. ● Is powered by your vehicle’s battery. No separate batteries are required.
4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, press and hold the programmed HomeLinkT button — releasing when the device begins to activate. WIC0987 3.
PROGRAMMING HOMELINKT FOR CANADIAN CUSTOMERS PROGRAMMING TROUBLEDIAGNOSIS CLEARING THE PROGRAMMED INFORMATION Prior to 1992, D.O.C. regulations required handheld transmitters to stop transmitting after 2 seconds.
1. Locate the training button on the garage door opener motor unit. Exact location and color of the button may vary by garage door opener brand. If there is difficulty locating the training button, reference the garage door opener Owner’s Manual. 2. Press the training button on the garage door opener motor unit (which may activate a training light). NOTE: Following step 2, there are 30 seconds in which to initiate step 3. 3.
3 Pre-driving checks and adjustments Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Intelligent Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Locking with inside lock knob . . . . . . . . . . . . . . . . . . . .
KEYS WPD0363 1. 2. 3. Two Intelligent Keys Mechanical keys (inside Intelligent Keys) Key number plate INTELLIGENT KEYS Your vehicle can only be driven with the Intelligent Keys which are registered to your vehicle’s Intelligent Key system components and NISSAN Vehicle Immobilizer System components. As many as 4 Intelligent Keys can be registered and used with one vehicle.
DOORS CAUTION Always carry the mechanical key installed in the Intelligent Key slot. Valet hand-off When you have to leave a key with a valet, give them the Intelligent Key itself and keep the mechanical key with you to protect your belongings. To prevent the glove box and the trunk from being opened during valet hand-off, follow the procedures below. SPA1951 Mechanical key The Intelligent Key contains the mechanical key.
Opening and closing windows (if so equipped) The driver’s door key operation allows you to open and close windows equipped with automatic operation at the same time. ● To open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. ● To close the windows, turn the driver’s door key toward the front of the vehicle for longer than 1 second after the door is locked.
Lockout protection When the power door lock switch (driver’s or front passenger’s side) is moved to the lock position with the Intelligent Key in the port and any door open, all doors will lock and unlock automatically. With the Intelligent Key left in the vehicle (not in the Intelligent Key port) and any door open, all doors will unlock automatically and a chime will sound after the door is closed.
INTELLIGENT KEY SYSTEM WARNING Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use. The Intelligent Key system can operate all the door locks using the remote controller function or pushing the request switch on the vehicle without taking the key out from a pocket or purse. The operating environment and/or conditions may affect the Intelligent Key system operation.
CAUTION ● Do not allow the Intelligent Key, which contains electrical components, to come into contact with water or salt water. This could affect the system function. If an Intelligent Key is lost or stolen, NISSAN recommends erasing the ID code of that Intelligent Key from the vehicle. This may prevent the unauthorized use of the Intelligent Key to operate the vehicle. For information regarding the erasing procedure, contact a NISSAN dealer. ● Do not drop the Intelligent Key.
SPA2038 OPERATING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified 1 . operating range from the request switch s When the Intelligent Key battery is discharged or strong radio waves are present near the operating location, the Intelligent Key system’s operating range becomes narrower, and the Intelligent Key may not function properly. The operating range is within 31.50 in (80 cm) 1 .
● Do not pull the door handle before pushing the door handle request switch. The door will be unlocked but will not open. Release the door handle once and pull it again to open the door. WPD0376 INTELLIGENT KEY OPERATION You can lock or unlock the doors without taking the key out of your pocket or bag. When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch within the range of operation. WPD0377 Locking doors 1.
CAUTION ● After locking the doors using the request switch, make sure that the doors have been securely locked by operating the door handles or the trunk opener switch. ● When locking the doors using the request switch, make sure to have the Intelligent Key in your possession before operating the request switch to prevent the Intelligent Key from being left in the vehicle. WPD0369 NOTE: ● Doors lock with the door handle request switch while the ignition switch is not in the LOCK position.
● Locking the doors with the remote controller. ● Switching the room light switch to the OFF position. WPD0377 Unlocking doors 1. Carry the Intelligent Key. 1 . 2. Push the door handle request switch s 3. The hazard warning lights flash once and the outside buzzer sounds once. 1 4. Push the door handle request switch s again within 5 seconds to unlock all doors. If a door handle is pulled while unlocking the doors, that door may not be unlocked.
When all doors are locked and the trunk lid is closed with the Intelligent Key inside the trunk, the outside buzzer will sound and the trunk will open. HOW TO USE THE REMOTE KEYLESS ENTRY FUNCTION The remote keyless entry function can operate all door locks using the remote keyless function of the Intelligent Key. The remote keyless function can operate at a distance of 33 ft (10 m) away from the vehicle. The operating distance depends upon the conditions around the vehicle.
The interior light illuminates for 30 seconds when a door is unlocked and the room light switch is in the DOOR position. CAUTION After locking the doors using the Intelligent Key, be sure that the doors have been securely locked by operating the door handles. The light can be turned off without waiting for 30 seconds by performing one of the following operations. ● Placing the ignition switch in the ON position. ● Locking the doors with the remote controller.
WPD0364 WPD0361 WPD0362 Releasing the trunk lid Using the panic alarm Silencing the horn beep feature Push the button for longer than 0.5 second to open the trunk lid. The trunk release button will not operate when the ignition switch is in the ON position or when the trunk cancel switch is in the OFF position. See “Cancel switch” in the “Pre-driving checks and adjustments” section.
The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. stolen, a chime or buzzer sounds from inside and outside the vehicle and a warning is displayed in the instrument panel. Deactivating the horn beep feature does not silence the horn if the alarm is triggered. When a chime or beep sounds or a warning is displayed, be sure to check the vehicle and the Intelligent Key.
Symptom When pushing the ignition switch to stop the engine The SHIFT P warning appears on the display and the inside warning chime sounds continuously. When opening the driver’s door to get out of the vehicle The inside warning chime sounds continuously.
HOOD TRUNK LID WPD0393 s 1 Pull the hood lock release handle located below the driver’s side instrument panel; the hood springs up slightly. 2 s Lift the lever at the front of the hood with your fingertips and raise the hood. 3 s 4 s Remove the support rod from the clamp. Insert the support rod into the hole on the passenger’s side of the hood. WARNING ● Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident.
● Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked, with the rear seatback and trunk lid securely latched when not in use, and prevent children’s access to car keys. To open the trunk lid, push the opener lever down. To close the trunk lid, lower and push the trunk lid down securely. NOTE: You can open the trunk lid with the Intelligent Key.
FUEL-FILLER DOOR To open the trunk from the inside, pull the illuminated release handle until the lock releases and push up on the trunk lid. The release handle is made of a material that glows in the dark after a brief exposure to ambient light. The handle is located inside the trunk compartment on the interior of the trunk lid. LPD0397 LPD0263 OPENER OPERATION FUEL-FILLER CAP The fuel-filler door release is located on the floor to the left of the driver’s seat.
WARNING ● Gasoline is extremely flammable and highly explosive under certain conditions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling. ● Fuel may be under pressure. Turn the cap a third of a turn, and wait for any “hissing” sound to stop to prevent fuel from spraying out and possibly causing personal injury. Then remove the cap.
TILTING TELESCOPIC STEERING COLUMN SUN VISORS TELESCOPIC OPERATION 1 all the way towards you and Pull the lever s adjust the steering wheel forward or backward in 3 , to the desired position. Release the direction s lever after the desired telescopic position is achieved. WARNING LPD0398 TILT OPERATION 1 all the way towards you and Pull the lever s adjust the steering wheel up or down in direction 2 to the desired position. Release the lever after s the desired tilt position is achieved.
MIRRORS 3 s Slide the extension sun visor (if so equipped) in or out as needed. CAUTION Do not store the sun visor before returning the extension to its original position. LPD0400 WPD0126 VANITY MIRRORS REARVIEW MIRROR (if so equipped) To access the vanity mirror, pull the sun visor down and flip open the mirror cover. Some vanity mirrors are illuminated and turn on when the mirror cover is open. 1 reduces glare from the The night position s headlights of vehicles behind you at night.
To turn on the automatic anti-glare feature, press button again. The indicator light will the turn on. ● Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident. For information on HomeLinkT Universal Transceiver operation, see “HomeLinkT Universal Transceiver” in the “Instrument and controls” section of this manual.
LPD0346 WPD0170 Electric control type (if so equipped) Manual control type (if so equipped) The outside mirror remote control only operates when the ignition switch is in the ACC or ON position. The outside mirror can be moved in any direction for a better rear view. Rotate the control lever to select the right or left mirror. Adjust the mirror to the desired position by moving the control lever. WPD0056 Manual folding outside mirrors (if so equipped) Push the mirrors backward to fold them.
MEMO Pre-driving checks and adjustments 3-25
4 Monitor, climate, audio, phone and voice recognition systems Control panel buttons (if so equipped) . . . . . . . . . . . . . . . 4-2 Setting up the start-up screen . . . . . . . . . . . . . . . . . . . 4-3 How to use the SETUP button . . . . . . . . . . . . . . . . . . . 4-3 button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Rearview monitor (if so equipped) . . . . . . . . . . . . . . . . . . . 4-7 How to read the displayed lines . . . . . . . . . . . . . . . . . .
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . 4-58 BluetoothT Hands-Free Phone System with Navigation System (if so equipped) . . . . . . . . . . . . . . . . . 4-59 Pairing procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61 Phone download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62 Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63 Receiving a call . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTROL PANEL BUTTONS (if so equipped) WARNING ● Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock.
When you use this system, make sure the engine is running. To proceed to the next step, refer to the separate Navigation System Owner’s Manual. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. Reference symbols: SETUP button — This is a button on the control panel. “Display” key — This is a select key on the touchscreen. By touching this key you can proceed to the next function.
button. The message “Re● Press the suming display” will appear and the Display “ON” key will be automatically turned on, the amber indicator will illuminate. LHA0748 LHA0749 Display settings Display off: Touch the “Display” key. The display screen will appear. Touch the Display “ON” key. The indicator of the display turns off; touch the “Back” key to accept the change. The message above will be displayed briefly.
Clock Format: key or the key to choose Touch the either the 12-hour clock display or the 24-hour clock display. Clock Adjusting the time: The following display will appear when pressing the SETUP button, then touching the “Clock” key. On-screen Clock: When this item is turned on, a clock is always displayed in the upper right corner of the screen. This clock will indicate the time almost exactly because it is always adjusted by the GPS system.
BUTTON Unit: US — mile, °F, MPG Metric: — km, °C, L/100 km The settings are automatically saved when you exit the menu by touching the “Back” key. Phone settings For information on the phone settings, see “BluetoothT Hands-Free Phone System with Navigation (if so equipped)” later in this section. To change the display brightness, press the button. Pressing the button again will change the display to the day or the night display. Then, adjust the brightness by touching the key or the key.
REARVIEW MONITOR (if so equipped) When the selector lever is shifted into the R (Reverse) position, the monitor display shows view directly to the rear of the vehicle. WARNING ● The system is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground. ● The rearview camera is a convenience but it is not a substitute for proper backing.
ADJUSTING THE SCREEN To adjust the quality of the screen, press the SETUP button. ● To adjust the Brightness, Tint, Contrast, Display ON/OFF and Color of the rearview monitor, press the SETUP button with the rearview monitor on, then touch the “–” or “+” key on the item and adjust the level. ● Do not adjust the Brightness, Contrast, Tint and Color of the rearview monitor while the vehicle is moving.
VENTILATORS WHA0736 Right and Left Adjust air flow direction by moving the ventilator slides. WHA0737 Center WHA0688 Rear (if so equipped) Open or close the ventilators by using the dial. Move the dial toward the to open the ventilators or toward the to close them.
HEATER AND AIR CONDITIONER (manual) WARNING ● The air conditioner cooling function operates only when the engine is running. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
— Air flows from center and side ventilators. — Air flows from center and side ventilators and foot outlets. — Air flows mainly from foot outlets. — Air flows from defroster outlets and foot outlets. — Air flows mainly from defroster outlets. Temperature control dial WHA0739 Type B 1. 2. 3. 4. 5. 6. 7. 8.
● for maximum cooling when using the air conditioner. HEATER OPERATION Heating Defrosting or defogging Off position (Indicator light off): Outside air is drawn into the passenger compartment and distributed through the selected outlet. This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets. Use the off position for normal heater or air conditioner operation. 1. Press the button to the OFF position for normal heating.
Bi-level heating The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets. 1. Press the button to the OFF position. 2. Press the air flow control button. 3. Turn the fan control dial to the desired position. 4. Turn the temperature control dial to the desired position. Heating and defogging This mode heats the interior and defogs the windshield. 1. Press the air flow control button. 2. Turn the fan control dial to the desired position. 3.
1. Press the air flow control button. 2. Turn the fan control dial to the desired position. 3. Press the comes on. button. The indicator light When the or are selected, the air conditioner automatically turns on (however, the indicator light will not illuminate) if the outside temperature is more than 36°F (2°C). The air conditioning system will continue to operate until the fan control is turned to OFF or the vehicle is shut off, even if an air flow control button other than is selected.
WHA0741 WHA0742 Monitor, climate, audio, phone and voice recognition systems 4-15 Z REVIEW COPY—2007 Altima (alt) Owners Manual—USA_English (nna) 10/26/06—debbie X
WHA0743 WHA0744 4-16 Monitor, climate, audio, phone and voice recognition systems Z REVIEW COPY—2007 Altima (alt) Owners Manual—USA_English (nna) 10/26/06—debbie X
WHA0745 Monitor, climate, audio, phone and voice recognition systems 4-17 Z REVIEW COPY—2007 Altima (alt) Owners Manual—USA_English (nna) 10/26/06—debbie X
HEATER AND AIR CONDITIONER (automatic) (if so equipped) ● Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up. Start the engine and operate the controls to activate the air conditioner. AUTOMATIC OPERATION Cooling or heating (auto) WHA0774 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
● The temperature of the passenger compartment will be maintained automatically. Air flow distribution, fan speed and A/C on/off are also controlled automatically. ● A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly. This does not indicate a malfunction. Dehumidified defrosting or defogging 1. Push the defroster control button to turn the system on. The indicator light in the button will illuminate.
SERVICING AIR CONDITIONER AUDIO SYSTEM The air conditioner system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. RADIO This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system.
Reception conditions will constantly change because of vehicle movement. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception. FM RADIO RECEPTION Range: FM range is normally limited to 25 – 30 miles (40 – 48 km), with monaural (single channel) FM having slightly more range than stereo FM.
Compact disc (CD) player CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player. ● Trying to load a CD with the CD door closed could damage the CD and/or CD changer. AUDIO OPERATION PRECAUTIONS ● CDs that are in poor condition or are dirty, scratched or covered with fingerprints may not work properly. ● The following CDs may not work properly: ● Copy control compact discs (CCCD) ● Only one CD can be loaded into the CD player at a time.
1. MP3 or WMA file not supported → “UNPLAYABLE TRACK” → Go to next track 2. CD ROM → “No Audio Track” → Eject disc and go to the last mode (CD player only) / Go to next disc (CD changer only) 3. TEMP/MECH ERROR → “PRESS EJECT” 4. READ/FOCUS ERROR → “CHECK DISC” CHECK DISC: ● Confirm that the CD is inserted correctly (the label side is facing up, etc.). ● Confirm that the CD is not bent or warped and it is free of scratches. PRESS EJECT: This is an error due to excessive temperature inside the player.
● If there is a file in the top level of the disc, “Root Folder” is displayed. ● The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order. WHA0773 Playback order chart Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. ● The names of folders not containing MP3 or WMA files are not shown in the display.
Specification chart: Supported media CD, CD-R, CD-RW Supported file systems MP3 Supported versions*1 WMA ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. Version MPEG1, MPEG2, MPEG2.5 Sampling frequency 8 kHz - 48 kHz Bit rate 8 kbps - 320 kbps, VBR Version WMA7, WMA8, WMA9 Sampling frequency 32 kHz - 48 kHz Bit rate 48 kbps - 192 kbps, VBR Tag information ID3 tag VER1.0, VER1.1, VER2.2, VER2.
Troubleshooting guide: Symptom Cause and Countermeasure Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. Cannot play If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature. Files with extensions other than “.MP3”, “.mp3” or “.wma” cannot be played.
12. 13. 14. 15. 16. 17. RADIO button CD button DISP button PRESET A·B·C button Station select (1 - 6) buttons pause/mute button FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) Audio main operation PWR/VOL control knob Place the ignition switch in the ACC or ON position, then press the PWR/VOL control knob. If you listen to the radio with the engine not running, place the ignition in the ACC position.
AUDIO button (Bass, Treble, Fade and Balance) Press the AUDIO button to change the mode as follows: Bass → Treble → Fade → Balance → Beep ON/OFF → Audio or off → Bass To adjust Bass, Treble, Fade and Balance press the AUDIO button until the desired mode appears in the display. Press the TUNE/FF·REW or to adjust Bass and Treble to the desired level. You can also use the TUNE/FF·REW button to adjust Fade and Balance mode.
When the RADIO button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. blinks in the display. Pressing the SCAN button again during this 5 second period stops scan tuning and the radio remains tuned to that station. If a compact disc is playing when the RADIO button is pressed, the compact disc will automatically be turned off and the last radio station played will come on.
vances 1 additional track. The track number appears in the display window. (When the last track on the compact disc is skipped, the first track is played.) When is pressed, the track being played returns to the beginning. Press several times to skip back several tracks. Each time the button is pressed the CD moves back 1 track. CD EJECT: When the button is pressed with a compact disc loaded, the compact disc will be ejected.
9. 10. 11. 12. 13. 14. 15. 16. 17. RDM/RPT button PWR/VOL control knob AUX button RADIO* button CD button DISP button PRESET A·B·C button Station and CD select (1 - 6) buttons CD load button *No satellite radio reception is available unless there is an active XMT or SIRIUS™ satellite radio service subscription. Satellite radio is not available in Alaska, Hawaii and Guam. If satellite radio is not operational then pressing the RADIO button will switch between FM and AM bands. LHA0729 Type A 1. 2. 3. 4.
Audio main operation PWR/VOL control knob Place the ignition switch in the ACC or ON position, and then press the PWR/VOL control knob while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off. To turn the system off, press the PWR/VOL control knob. Turn the PWR/VOL control knob to adjust the volume. This vehicle may be equipped with Speed Sensitive Volume (SSV) for audio. The audio volume changes as the driving speed changes.
● Track time displays the amount of time the track has played. Satellite radio equipped) ● Album title displays the title of the CD being played. To change the text displayed when listening to satellite radio (if so equipped) press the DISP button. The DISP button will scroll through the broadcast information as follows: Channel number → Category name → Channel name → Artist name → Song title. ● Song title displays the title of the selected CD track.
SCAN (tuning) button: Press the SCAN button. SCAN illuminates in the display window. Scan tuning begins from low to high frequencies. Scan tuning stops for 5 seconds at each broadcasting station that has sufficient signal strength. When scanning, SCAN blinks in the display. Pressing the SCAN button again during this 5 second period stops scan tuning and the radio remains tuned to that station.
TUNE/FF·REW (fast forward, rewind) button: When the TUNE/FF·REW button or button is pressed while the compact disc is playing, the compact disc plays at an increased speed while fast forwarding or rewinding. When the button is released, the CD returns to normal play speed. MP3 TUNE/FF·REW button: While playing an MP3, press the TUNE/FF·REW button or to scan forward or backward through available folders. To fast forward or rewind through an MP3 audio track, press the TUNE/FF·REW button or for more than 1.
SCAN button: 1 Disc, All Tracks While listening to a CD, press the SCAN button to preview the first 10 seconds of each track on the CD playing. Pressing the SCAN button again during this 10 second period stops the scan and the CD remains on that track. All Discs, 1 Track While listening to a CD with other CDs loaded into the CD changer, press and hold the SCAN button for approximately 2 seconds, to preview the first 10 seconds of the first track on the CDs loaded.
1. 2. RADIO* button Touch-screen keys (vary depending on what function is selected) 3. SEEK/TRACK button 4. TUNE·FOLDER and AUDIO control knob (BASS, TREBLE, BALANCE, FADE and SSV (if so equipped)) 5. Station and CD select (1 - 6) buttons 6. CD insert slot 7. CD changer select (1 - 6) buttons 8. CD eject button 9. AUX jack 10. A·B·C button 11. ON·OFF/VOL control knob 12. CD/AUX button *No satellite radio reception is available unless there is an active XMT satellite radio service subscription.
FM/AM/SAT RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) No satellite radio reception is available unless there is an active XMT satellite radio service subscription. Satellite radio is not available in Alaska, Hawaii and Guam. If satellite radio is not operational then pressing the RADIO button will switch between FM and AM bands. Reference symbols: RADIO button — This is a button on the radio. By pressing this button you can select the item or perform this action.
CD display mode While listening to a CD or an MP3/WMA CD certain text might be displayed (when CD encoded with text is being used). ● Category name displays the category name of the selected satellite radio station. ● Channel name displays the channel name of the selected satellite radio station.
Station memory operations: 18 stations can be set for the FM, AM or SAT (Satellite if so equipped) radio to the A, B and C preset button in any combination of FM, AM or SAT stations. 1. Press the A·B·C button or the “Preset” key to select preset channel A, B or C. 2. Press the RADIO button to select the desired FM, AM or SAT station band. 3. Tune to the desired station using manual tuning, seek tuning or scan tuning.
When the CD/AUX button is pressed with the compact disc loaded but the radio playing, the radio will automatically be turned off and the compact disc will start to play. TUNE·FOLDER knob: While playing an MP3 CD to skip through folders turn the TUNE·FOLDER knob right or left to skip forward or backward through the available folders. This function will only operate on an MP3 CD with multiple folders. “Folder” key: While playing an MP3 CD you can select a track inside a folder.
“Random” key: When the “Random” key is touched while a compact disc is played, the play pattern can be changed as follows: CD: ALL DISC RDM → 1 DISC RDM MP3 CD: ALL DISC RDM → 1 DISC RDM → 1 FOLDER RDM ALL DISC RDM: Tracks from all discs will be played randomly. 1 DISC RDM: Tracks from the disc that is currently playing will be played randomly. 1 FOLDER RDM: Folders from that disc that is currently playing will be played randomly. CD EJECT: Current/Selected disc: button.
● A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated. STEERING WHEEL SWITCH FOR AUDIO CONTROL (if so equipped) LHA0752 LHA0753 Type A 1. 2. 3. Type B Source select and Power on switch Tuning switch Volume control switch 1. 2. 3.
*This mode is only available when a CD is loaded. Change disc (CD) (if so equipped): **This mode is only available when a compatible auxiliary device is plugged into the AUX jack. or for more Push the tuning switch than 1.5 seconds to change the playing disc up or down. While in one of the preset radio station banks (A, or to B or C), use the tuning switch select one of the preset radio stations (1 – 6). Volume control switch Push the volume control switch to increase or decrease the volume.
CAR PHONE OR CB RADIO When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following precautions, otherwise the new equipment may adversely affect the engine control system and other electronic parts. WARNING ● A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular telephones while driving.
module when the ignition switch is turned to the ON position with the paired cellular phone turned on and carried in the vehicle. You can register up to 5 different BluetoothT cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. Before using the BluetoothT Hands-Free Phone System, refer to the following notes. ● Set up the wireless connection between a cellular phone and the in-vehicle phone module before using the hands-free phone system.
– Your cellular phone is locked to prevent it from being dialed. When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person’s voice during a call. Do not place the cellular phone in an area surrounded by metal or far away from the in-vehicle phone module to prevent tone quality degradation and wireless connection disruption.
The command given is picked up by the microphone, and voice feedback is given when the command is accepted. ● If you need to hear the available commands for the current menu again, say “Help” and the system will repeat them. ● If a command is not recognized, the system announces, “Command not recognized. Please try again.” Repeat the command in a clear voice. ● If you want to go back to the previous command, you can say “Go back” or “Correction” any time the system is waiting for a response.
PHONE/END button to cancel a VR Press the session or end a call. GETTING STARTED The following procedures will help you get started using the BluetoothT Hands-Free Phone System with NISSAN Voice Recognition. For additional command options, refer to “List of voice commands” later in this section. Choosing a language LHA0757 CONTROL BUTTONS The control buttons for the BluetoothT HandsFree Phone System are located on the steering wheel.
Pairing procedure NOTE: The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Main Menu A “Setup” s B “Pair Phone” s C “New Phone” s D Initiate from handset s E Name phone s F Assign priority s G Choose ringtone s 1. Press the button on the steering wheel. The system announces the available commands. A . The system acknowledges 2.
B . For 3. Say the number you wish to call s example, 555-1212 can be said as “five five five one two one two.” See “How to say numbers” earlier in this section for more information. 4. When you have finished speaking the phone number, the system repeats it back and announces the available commands. C . The system acknowledges 5. Say: “Dial” s the command and makes the call.
When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name. If there are multiple locations associated with the name, the system asks you to choose the location. Once you have confirmed the name and location, the system begins the call. B Number (speak digits) s When prompted by the system, say the number you wish to call. Refer to “How to say numbers” and “Making a call by entering a phone number” earlier in this section for more details.
“Phone book” NOTE: When prompted by the system, say the name you would like to give the new entry. For example, say: “Mary.” Phone book commands are not available when the vehicle is moving. Main Menu “Phone Book” A “New Entry” s B “Edit” s C “Delete” s D 9List Names” s If the name is too long or too short, the system tells you, then prompts you for a name again. Also, if the name sounds too much like a name already stored, the system tells you, then prompts you for a name again.
The system acknowledges the location. C “Delete” s The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone’s memory. Use the Delete command to erase one entry from the phone book, all entries from the phone book, the current redial number or the current call back number. Enter a phone number by voice command: For example, say: “five five five one two one two. ” See “How to say numbers” earlier in this section for more information.
B “Play” s The system plays back all the memos in the order of newest to oldest. The system ends the VR session. If there are no memos recorded, the system announces “No messages to play.” The system ends the VR session. C “Delete” s The Delete command erases all memos. The system asks you to confirm this action before deleting all memos. “Setup” Main Menu “Setup” A “Pair Phone” s B “List Phone” s Use the Setup command to change options associated with the BluetoothT Hands-Free Phone System.
D “Change priority” s Use the Change Priority command to change the priority level of the active phone. The priority level determines which phone is active when more than one paired BluetoothT phone is in the vehicle. The system states the priority level of the active phone and asks for a new priority level (1, 2, 3, 4, 5). If the new priority level is already being used for another phone, the two phones will swap priority levels.
Training procedure The procedure for training a voice is as follows. 1. Position the vehicle in a reasonably quiet outdoor location. 2. Sit in the driver’s seat with the engine running, the parking brake on, and the transmission in P (Park) (AT and CVT models) or N (Neutral) (MT models). 3. Press and hold the than 5 seconds. button for more 4.
● call star two zero nine five ● Correction ● call five six two eight zero ● delete phone ● setup change ring tone ● dial six six four three seven ● dial eight three zero five one ● dial seven four oh one eight TROUBLESHOOTING GUIDE ● Home ● setup main menu ● four three pause two nine pause zero ● Delete ● delete redial number ● dial nine seven two six six The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions.
BLUETOOTHT HANDS-FREE PHONE SYSTEM WITH NAVIGATION SYSTEM (if so equipped) WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. ● If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so. CAUTION To avoid draining the vehicle battery, use a phone after starting the engine.
module when the ignition switch is turned to the ON position with the paired cellular phone turned on and carried in the vehicle. You can register up to 5 different BluetoothT cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. NISSAN Voice Recognition system supports the phone commands, so dialing a phone number using your voice is possible. For more details, see NISSAN Voice Recognition System later in this section.
WHA0788 PAIRING PROCEDURE 1. Press the SETUP button, then touch the “Phone” key. LHA0760 LHA0761 5. When the pairing is completed, the screen will return to the BluetoothT setup display. 2. Scroll to the bottom of the list and touch the “Bluetooth Setup” key. 3. Touch the “Pair Phone” key, then touch one of the “None (Add New)” keys. 4. When a PIN code appears on the screen, operate the BluetoothT cellular phone to enter the PIN code.
LHA0762 LHA0763 LHA0764 5. Operate the cellular phone to send a person’s name and phone number from the memory of the cellular phone. The memory sending procedure from the cellular phone varies according to each cellular phone manufacturer. See the cellular phone Owner’s Manual for more details. 3. Touch one of the “None (Add New)” keys from the name list of the phonebook. 6. If you want to add a voice tag, touch the “Yes” key on the Add a voice tag? screen.
There are different methods to input a phone number. Select one of the following options instead of the “Bluetooth” key in step 4 above. b. Press and hold the phone steering wheel switches. button on the There are different methods to make a call. Select one of the following options instead of the “Phonebook” key in step 2 above. Enter Data by Keypad: Input the name and phone number manually. Redial: Dial the previously dialed number again.
Hold Call: Continue to hold call. Reject Call: Reject an incoming call. To finish the call, follow the three procedures listed below. a. Touch the “Reject Call” key on the display. button on the b. Press and hold the phone steering wheel switches. LHA0766 LHA0767 RECEIVING A CALL DURING A CALL When you hear a phone ring, the display will change to phone mode. To receive a call, follow the two procedures listed below. There are some options available during a call.
● Delete Downloaded Phonebook: Delete all of the downloaded phonebook entries. Enter Digit : Brings up a keypad, enter digits when needed. For example, entering your PIN number for voicemail. ● Delete an Entry of Downloaded Phonebook: Delete a single entry from the downloaded phonebook. Touch the corresponding letter key, then touch on the name key you wish to delete. Touch the “Yes” key to delete the entry. Cancel Mute: This will appear after the “Mute” key is touched. Mute will be cancelled.
NISSAN VOICE RECOGNITION SYSTEM (if so equipped) ● Bluetooth Hands-Free: If this item is turned off, the connection between the cellular phone and the in-vehicle phone module will be canceled. The NISSAN Voice Recognition system allows hands-free operation of the systems equipped on this vehicle, such as the phone and navigation systems. ● Paired Phone List: Up to 5 registered cellular phones are shown on the list. To operate NISSAN Voice Recognition, press the button located on the steering wheel.
● If you want to cancel the command, press button for 2 seconds and hold the during feedback. The system will announce: “Voice canceled.” ● If you want to adjust the volume of the voice feedback, press the volume control buttons (2 or +) on the steering wheel while being provided with the feedback. Operating tips To get the best performance out of NISSAN Voice Recognition, observe the following: ● Keep the interior of the vehicle as quiet as possible.
How to say commands Example: “[PHONE] DIAL/CALL ” stands for the following possible commands. DIAL<1 to 32 phone number digits> CALL <1 to 32 phone number digits> PHONE DIAL <1 to 32 phone number digits> Help commands ● “COMMAND LIST”, “VOICE HELP” or “HELP” Gives spoken information about NISSAN Voice Recognition and displays the list of help commands. Phone commands ● “[PHONE] DIAL ” or “CALL ” Dials the phone number given in the command.
Symptom/error message Displays “COMMAND NOT RECOGNIZED” or he system fails to interpret the command correctly. Solution 1. Ensure that the command format is valid, see Command list in this section. 2. Speak clearly without pausing between words and at a level appropriate to the ambient noise level. 3. Ensure that the ambient noise level is not excessive, for example, windows open or defrost on. NOTE: If it is too noisy to use the phone, it is likely that voice commands will not be recognized. 4.
MEMO 4-70 Monitor, climate, audio, phone and voice recognition systems
5 Starting and driving Precautions when starting and driving. . . . . . . . . . . . . . . . 5-2 Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . 5-2 Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 5-3 Avoiding collision and rollover . . . . . . . . . . . . . . . . . . . . 5-5 Drinking alcohol/drugs and driving. . . . . . . . . . . . . . . . 5-5 Push-Button Ignition Switch . . . . . . . . . . . . . .
PRECAUTIONS WHEN STARTING AND DRIVING WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunctions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating conditions are detected.
● The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving). ● The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light.
FCC Notice: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.
PUSH-BUTTON IGNITION SWITCH the selector lever is moved to the P (Park) position (CVT) or N (Neutral) position (MT). WARNING ● Do not operate the push-button ignition switch while driving the vehicle except in an emergency. (The engine will stop when the ignition switch is pushed 3 consecutive times or the ignition switch is pushed and held for more than 2 seconds.) If the engine stops while the vehicle is being driven, this could lead to a crash and serious injury.
Some indicators and warnings for operation are displayed on the vehicle information display. See “Vehicle information display” in the “Instruments and controls” section. PUSH-BUTTON IGNITION SWITCH POSITIONS LOCK (Normal parking position): CAUTION Do not leave the vehicle with the ignition switch in ACC or ON positions when the engine is not running for an extended period. This can discharge the battery. INTELLIGENT KEY BATTERY DISCHARGE The ignition switch can only be locked in this position.
BEFORE STARTING THE ENGINE NOTE: The Intelligent Key port does not charge the Intelligent Key battery. If you see the low battery indicator, replace the battery as soon as possible. See “Intelligent Key battery replacement” in the “Maintenance and do-it-yourself” section. CAUTION ● Never place anything except the Intelligent Key in the Intelligent Key port. Doing so may cause damage to the equipment.
STARTING THE ENGINE 1. Apply the parking brake. 2. Continuously Variable Transmission (CVT) model: Move the shift selector lever to P (Park) or N (Neutral). P (Park) is recommended. The starter is designed not to operate if the shift selector lever is in any of the driving positions. Manual transmission: Move the shift lever to N (Neutral). Depress the clutch pedal to the floor. The starter is designed not to operate unless the clutch pedal is fully depressed. 3. Push the ignition switch to the ON position.
DRIVING THE VEHICLE CONTINUOUSLY VARIABLE TRANSMISSION (CVT) (if so equipped) WARNING ● Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), D (Drive) or manual shift mode. Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident. ● Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up.
WARNING Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage. LSD0182 To move the selector lever: If the ignition switch is pushed to the OFF or ACC position for any reason while the vehicle is in N (Neutral), or any drive position, the shift selector lever cannot be moved to P (Park).
6 (Sixth): Use this position for all normal forward driving at highway speeds. 5 (Fifth): For driving up or down long slopes where engine braking would be advantageous. 4 (fourth), 3 (Third) and 2 (Second): Use for hill climbing or engine braking on downhill grades. M1 (First): LSD0182 Manual shift mode When the selector lever is shifted from D to the manual shift gate with the vehicle stopped or while driving, the transmission enters the manual shift mode. Shift ranges can be selected manually.
To move the shift selector lever, complete the following procedure: 1. Push the ignition switch to the LOCK position. 2. Apply the parking brake. 3. Remove the shift lock release cover as shown. 4. Insert a small screwdriver in the shift lock release slot and push down. LSD0183 Shift lock release If the battery charge is low or discharged, the shift selector lever may not be moved from the P (Park) position even with the brake pedal depressed and the selector lever button pushed.
tion. This will occur even if all electrical circuits are functioning properly. In this case, push the ignition switch to the OFF position and wait for 10 seconds. Then push the switch back to the ON position. The vehicle should return to its normal operating condition. If it does not return to its normal operating condition, have a NISSAN dealer check the transmission and repair if necessary.
1 and To back up, lift up on the shift lever ring s then move it to the R (Reverse) position after stopping the vehicle completely. The shift lever ring returns to its original position when the shift lever is moved to the N (Neutral) position. If it is difficult to move the shift lever into R (Reverse) or 1 (1st), shift into N (Neutral), then release the clutch pedal. Depress the clutch pedal again and shift into R (Reverse) or 1 (1st).
PARKING BRAKE Suggested maximum speed in each gear Downshift to a lower gear if the engine is not running smoothly, or if you need to accelerate. Do not exceed the maximum suggested speed (shown below) in any gear. For level road driving, use the highest gear suggested for that speed. Always observe posted speed limits, and drive according to the road conditions, which will ensure safe operation.
CRUISE CONTROL ● The SET indicator light may blink when the cruise control switch is turned ON while pushing the ACCEL/RES, COAST/SET, or CANCEL switch. To properly set the cruise control system, use the following procedures. WARNING Do not use the cruise control when driving under the following conditions: ● When it is not possible to keep the vehicle at a set speed. WSD0169 Type B 3. Type A, firmly depress the parking brake pedal and it will release.
To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the instrument panel comes on. Take your foot off the accelerator pedal. Your vehicle maintains the set speed. ● To pass another vehicle, depress the accelerator pedal. When you release the pedal, the vehicle returns to the previously set speed. ● The vehicle may not maintain the set speed when going up or down steep hills.
BREAK-IN SCHEDULE CAUTION During the first 1,200 miles (2,000 km), follow these recommendations to obtain maximum engine performance and ensure the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in shortened engine life and reduced engine performance. ● Avoid driving for long periods at constant speed, either fast or slow, and do not run the engine over 4,000 rpm. ● Do not accelerate at full throttle in any gear. ● Avoid quick starts.
PARKING/PARKING ON HILLS Continuously Variable Transmission (CVT) models: Move the shift selector lever to the P (Park) position. 3. To help prevent the vehicle from rolling into traffic when parked on an incline, it is a good practice to turn the wheels as illustrated. 1 ● HEADED DOWNHILL WITH CURB: s Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb.
POWER STEERING BRAKE SYSTEM The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.
To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function correctly. ANTI-LOCK BRAKING SYSTEM (ABS) (if so equipped) WARNING ● The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving techniques.
TRACTION CONTROL SYSTEM (TCS) (if so equipped) Normal operation The ABS operates at speeds above 3 - 6 MPH (5 - 10 km/h). When the ABS senses that one or more wheels are close to locking up, the actuator rapidly applies and releases hydraulic pressure. This action is similar to pumping the brakes very quickly. You may feel a pulsation in the brake pedal and hear a noise from under the hood or feel a vibration from the actuator when it is operating.
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM (if so equipped) ● When driving on extremely inclined surfaces such as higher banked corners, the traction control system may not opindicator erate properly and the light may come on. Do not drive on these types of roads. ● If wheels or tires other than the recommended ones are used, the traction control system may not operate properly and the indicator light may come on.
COLD WEATHER DRIVING ● If brake related parts such as brake pads, rotors and calipers are not standard equipment or are extremely deteriorated, the vehicle dynamic control system may not operate properly and the vehicle dynamic control off indicator light may come on. ● Do not modify the vehicle’s suspension.
DRAINING OF COOLANT WATER If the vehicle is to be left outside without antifreeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see “Changing engine coolant” in the “Maintenance and do-it-yourself” section of this manual. TIRE EQUIPMENT 1. SUMMER tires have a tread designed to provide superior performance on dry pavement. However, the performance of these tires will be substantially reduced in snowy and icy conditions.
ENGINE BLOCK HEATER (if so equipped) Engine block heaters are available through NISSAN dealers to assist in cold temperature starting. The engine block heater should be used when the outside temperature is 20° F (-7° C) or lower. To use the engine block heater: 1. Turn the engine off. 2. Open the hood and unwrap the engine block heater cord. 3. Plug the engine block heater cord into a grounded 3-wire, 3-pronged extension cord. 4.
MEMO 5-28 Starting and driving
6 In case of emergency Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 6-2 Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Push starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 If your vehicle overheats . . . . . . . . . . . . . . . .
FLAT TIRE TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. If the vehicle is being driven with low tire pressure, the TPMS will activate and warn you of it by the low tire pressure warning light.
WARNING ● Make sure the parking brake is securely applied and the manual transmission is shifted into R (Reverse), or the CVT is shifted into P (Park). ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. ● Never change tires if oncoming traffic is close to your vehicle. Wait for professional road assistance.
● Use the correct jack-up points. Never use any other part of the vehicle for jack support. ● Never jack up the vehicle more than necessary. ● Never use blocks on or under the jack. ● Do not start or vehicle is on the vehicle to move. for vehicles differentials. SAI0484 Removing the bolt-on wheel cover (if so equipped) CAUTION Do not use your hands to pry off wheel caps or wheel covers. Doing so could result in personal injury. The wheel covers are held on by the wheel nuts.
LCE0020 Always refer to the proper illustrations for the correct placement and jack-up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instructions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nuts until the tire is off the ground. 2.
JUMP STARTING 4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely A,s B,s C,s D, in the sequence illustrated (s E ). Lower the vehicle completely. s WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident. ● Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.
● Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting. ● Do not attempt to jump start a frozen battery. It could explode and cause serious injury. ● Your vehicle has an automatic engine cooling fan. It could come on at any time. Keep hands and other objects away from it. WCE0054 WARNING Always follow the instructions below.
PUSH STARTING CAUTION ● Always connect positive (1) to positive (1) and negative (2) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) — not to the battery. ● Make sure the jumper cables do not touch moving parts in the engine compartment and that the cable clamps do not contact any other metal. 5. Start the engine of the booster vehicle and let it run for a few minutes. 6.
IF YOUR VEHICLE OVERHEATS If your vehicle is overheating (indicated by an extremely high temperature gauge reading), or if you feel a lack of engine power, detect abnormal noise, etc. take the following steps. WARNING ● Do not continue to drive if your vehicle overheats. Doing so could cause engine damage or a vehicle fire. ● To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot.
TOWING YOUR VEHICLE When towing your vehicle, all State (Provincial in Canada) and local regulations for towing must be followed. Incorrect towing equipment could damage your vehicle. Towing instructions are available from a NISSAN dealer. Local service operators are generally familiar with the applicable laws and procedures for towing. To assure proper towing and to prevent accidental damage to your vehicle, NISSAN recommends having a service operator tow your vehicle.
CAUTION ● Never tow Continuously Variable Transmission (CVT) models with the front wheels on the ground or four wheels on the ground (forward or backward), as this may cause serious and expensive damage to the transmission. If it is necessary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels.
CAUTION ● Tow chains or cables must be attached only to the main structural members of the vehicle or the towing hooks (if so equipped). Otherwise, the vehicle body will be damaged. ● Do not use the vehicle tie downs to free a vehicle stuck in sand, snow, mud, etc. Never tow the vehicle using the vehicle tie downs or recovery hooks. LCE0138 VEHICLE RECOVERY (freeing a stuck vehicle) Front or Rear Do not use the hook to tow the vehicle. WARNING ● Stand clear of a stuck vehicle.
7 Appearance and care Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Glass . . . . . . . . . . . . . . . . . . . . . . .
CLEANING EXTERIOR In order to maintain the appearance of your vehicle, it is important to take proper care of it. To protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads. ● when contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface. ● when dust or mud builds up on the surface.
REMOVING SPOTS Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film. Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store.
CLEANING INTERIOR ● Do not apply wheel cleaners to the wheels when they are hot. The wheel temperature should be the same as ambient temperature. ● Apply a light coat of tire dressing to help prevent it from entering the tire tread/grooves (where it would be difficult to remove). ● Rinse the wheel to completely remove the cleaner within 15 minutes after the cleaner is applied. ● Wipe off excess tire dressing using a dry towel. Make sure the tire dressing is completely removed from the tire tread/grooves.
SEAT BELTS ● Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly. Do not use saddle soap, car waxes, polishes, oils, cleaning fluids, solvents, detergents or ammonia-based cleaners as they may damage the leather’s natural finish. The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them.
CORROSION PROTECTION MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION ● The accumulation of moisture-retaining dirt and debris in body panel sections, cavities, and other areas. ● Damage to paint and other protective coatings caused by gravel and stone chips or minor traffic accidents. ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION Moisture Accumulation of sand, dirt and water on the vehicle body underside can accelerate corrosion.
8 Maintenance and do-it-yourself Maintenance requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Explanation of general maintenance items . . . . . . . . . 8-2 Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Engine compartment check locations . . . . . . . . . . . . . . . . 8-6 Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE REQUIREMENTS Your new NISSAN has been designed to have minimum maintenance requirements with longer service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.
When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary.
and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. Engine coolant level* Check the coolant level when the engine is cold. Steering wheel Check for changes in the steering system, such as excessive freeplay, hard steering or strange noises. Engine drive belts* Make sure the drive belts are not frayed, worn, cracked or oily. Warning lights and chimes Make sure all warning lights and chimes are operating properly.
MAINTENANCE PRECAUTIONS When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. WARNING ● Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. For manual transmission models, move the shift lever to N (Neutral).
ENGINE COMPARTMENT CHECK LOCATIONS QR25DE engine 1. 2. 3. Power steering fluid reservoir Engine oil filler cap Brake fluid reservoir/Clutch fluid reservoir (M/T model) 4. Air cleaner 5. Fuse block 6. Battery 7. Fuse/Fusible link box 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Engine coolant reservoir 12.
VQ35DE engine 1. 2. 3. Power steering fluid reservoir Engine oil filler cap Brake fluid reservoir/Clutch fluid reservoir (M/T model) 4. Air cleaner 5. Fuse block 6. Battery 7. Fuse/Fusible link box 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Engine coolant reservoir 12.
ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with Genuine NISSAN Long Life Antifreeze/Coolant to provide year-round antifreeze and coolant protection. The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary. WARNING ● Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down.
ENGINE OIL CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheating. WARNING ● To avoid the danger of being scalded, never change the coolant when the engine is hot. ● Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pressure fluid escaping from the radiator. ● Avoid direct skin contact with used coolant.
WDI0492 WDI0214 CAUTION Oil level should be checked regularly. Operating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. QR25DE CHANGING ENGINE OIL 1. Park the vehicle on a level surface and apply the parking brake. 2. Start the engine and let it idle until it reaches operating temperature, then turn it off. A cap by turning it 3. Remove the oil filler s counterclockwise. 4. Place a large drain pan under the drain plug B.
● Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. ● Keep used engine oil out of reach of children. CAUTION Be careful not to burn yourself. The engine oil may be hot. The drain and refill capacity depends on the oil temperature and drain time. Use these specifications for reference only. Always use the dipstick to determine when the proper amount of oil is in the engine. 8. Start the engine.
CONTINUOUSLY VARIABLE TRANSMISSION (CVT) FLUID 7. Screw on the oil filter until a slight resistance is felt, then tighten an additional 2/3 turn. 8. Start the engine and check for leakage around the oil filter. Correct as required. 9. Turn the engine off and wait more than 10 minutes. Check the oil level. Add engine oil if necessary. WARNING ● Use only Genuine NISSAN CVT Fluid NS-2. Do not mix with other fluids.
POWER STEERING FLUID BRAKE AND CLUTCH FLUID For further brake and clutch fluid specification information, refer to “Capacities and recommended fuel/lubricants” in the “Technical and consumer information” section of this manual. WARNING ● Use only new fluid from a sealed container. Old, inferior or contaminated fluid may damage the brake and clutch systems. The use of improper fluids can damage the brake system and affect the vehicle’s stopping ability.
WINDOW WASHER FLUID Refill the reservoir more frequently when driving conditions require an increased amount of window washer fluid. Recommended fluid is Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent. CAUTION ● Do not substitute engine anti-freeze coolant for window washer solution. This may result in damage to the paint. LDI0558 CLUTCH FLUID Check the clutch fluid level in the reservoir (manual transmissions only).
BATTERY ● Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water. ● When working on or near a battery, always wear suitable eye protection and remove all jewelry. ● Make certain the terminal connections are clean and securely tightened. ● Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.
DRIVE BELTS Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer. LDI0565 QR25DE engine 1. 2. 3. 4. 5. LDI0302 2. Check the fluid level in each cell.
SPARK PLUGS 1. Visually inspect the belt(s) for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer. 2. Have the belts checked regularly for condition and tension in accordance with the maintenance schedule found in the “NISSAN Service and Maintenance Guide”. LDI0564 VQ35DE engine 1. 2. 3. 4.
AIR CLEANER WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. CAUTION CAUTION Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs. If replacement is required, see your NISSAN dealer for assistance. Be sure to use the correct socket to remove the spark plugs. An incorrect socket can damage the spark plugs.
WINDSHIELD WIPER BLADES ● Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed. Doing so could result in serious injury. IN-CABIN MICROFILTER The in-cabin microfilter restricts the entry of airborne dust and pollen particles and reduces some objectionable outside odors. The filter is located behind the glove box. Refer to the “NISSAN Service and Maintenance Guide” for change intervals.
CAUTION ● After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened. ● Make sure the wiper blades contact the glass; otherwise the arms may be damaged from wind pressure. WDI0594 REPLACING Replace the wiper blades if they are worn. 1. Lift the wiper arm away from the windshield. 2 s Push the release tab, then move the wiper blade down the wiper arm to remove. 3 s Remove the wiper blade. 4.
BRAKES FUSES If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. SELF-ADJUSTING BRAKES Your vehicle is equipped with self-adjusting brakes. Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate maintenance schedule information in the “NISSAN Service and Maintenance Guide”. The front and rear disc-type brakes self-adjust every time the brake pedal is applied.
3. Remove the fuse box cover by pushing the tab and lifting the cover up. 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. LDI0457 If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration. This will not affect the performance of the fuse. Make sure the fuse is installed in the fuse box securely.
WDI0452 A , replace it with a new 5. If the fuse is open s B. fuse s 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts. WDI0402 PASSENGER COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover.
BATTERY REPLACEMENT WDI0452 Type A LDI0456 Type B A , replace it with an 4. If the fuse is open s B. equivalent good fuse s 5. Push the fuse box cover to install. 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.
INTELLIGENT KEY BATTERY Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Replace the battery in the Intelligent Key as follows: 1. Remove the mechanical key from the Intelligent Key. A into the slit s B 2. Insert a small screwdriver s of the corner and twist it to separate the upper part from the lower part.
LIGHTS HEADLIGHTS Replacing the xenon headlight bulb (if so equipped) WARNING cHIGH VOLTAGE When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer. For additional information, see “Headlight and turn signal switch” in the “Instruments and controls” section.
EXTERIOR AND INTERIOR LIGHTS Item Wattage (W) Bulb No.* Headlight assembly Low (Halogen) Low (Xenon) High 55 H11 (special) D2R 65 H9 27/8 1157NA Front fog light 55 H11 Step light — 158 Park/Turn Rear combination light Tail/Stop 8/27 3157KX Turn 27 3156 Backup (reversing) 13 912 Sidemarker 5 168 License plate light 5 W5W 18 921 High-mounted stop light Inside Spoiler (if so equipped) See a NISSAN dealer for assistance.
1. 2. 3. 4. 5. 6. 7. 8. Rear map light Front map light Step light Headlamp assembly Fog light (if so equipped) High-mount stoplight (if so equipped) Trunk light Spoiler mounted stoplight (if so equipped) 9. Rear combination light 10.
WDI0234 Step light LDI0571 Front map light WDI0263 Replacement procedures All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens, lamp and/or cover.
LDI0572 Rear map light WDI0320 High-mounted stop light (rear window) WDI0343 Trunk light 8-30 Maintenance and do-it-yourself Z REVIEW COPY—2007 Altima (alt) Owners Manual—USA_English (nna) 10/27/06—debbie X
WHEELS AND TIRES If you have a flat tire, see the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h).
● Before taking a long trip, or whenever you heavily load your vehicle, use a tire pressure gauge to ensure that the tire pressures are at the specified level. ● Do not drive your vehicle over 85 MPH (137 km/h) unless it is equipped with high speed rated tires. Driving faster than 85 MPH (137 km/h) may result in tire failure, loss of control and possible injury.
6 s 4. Read the tire pressure on the gauge stem and compare to the specification shown on the Tire and Loading Information label. Spare tire size (if so equipped). 5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. 6. Install the valve stem cap. LDI0393 Checking tire pressure 7. Check the pressure of all other tires, including the spare. 1.
Size Front Original Tire Rear Original Tire Spare Tire P215/60/R16 P215/55R17 P215/60R16 P215/55R17 T135/70R16 T135/90R16 Cold Tire Inflation Pressure 220 kPa, 32 PSI 230 kPa, 33 PSI 220 kPa, 32 PSI 230 kPa, 33 PSI 420 kPa, 60 PSI WDI0394 Example TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires.
7. H: Tire speed rating. You should not drive the vehicle faster than the tire speed rating. WDI0395 Example 1 Tire size (example: P215/65R15 95H) s 1. P: The 9P9 indicates the tire is designed for passenger vehicles (not all tires have this information). 2. Three-digit number (215): This number gives the width in millimeters of the tire from sidewall edge to sidewall edge. 3. Two-digit number (65): This number, known as the aspect ratio, gives the tire’s ratio of height to width. 4.
3 Tire ply composition and material s The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 4 Maximum permissible inflation press sure WDI0396 Example 2 TIN (Tire Identification Number) for a s new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Department Of Transportation.
7 The word “radial” s The word “radial” is shown if the tire has radial structure. 8 Manufacturer or brand name s Manufacturer or brand name is shown.
studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS CAUTION Only certain SAE class “S” tire chains can be used on this vehicle. Using the wrong Class “S” chains on this vehicle will cause damage to the vehicle. If you plan to use tire chains/cables, you should use a tire chain that meets the minimum clearances for your vehicle. LDI0574 Use of tire chains may be prohibited according to location.
Wheel nut tightening torque: 83 ft-lb (112 N·m) The wheel nuts must be kept tightened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. WARNING ● After rotating the tires, check and adjust the tire pressure. WDI0258 CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km). See “Flat tire” in the “In case of emergency” section of this manual for tire replacing procedures.
● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced. ● Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be obvious. Replace the tires as necessary to prevent tire failure and possible personal injury. ● Improper service of the spare tire may result in serious personal injury.
● Do not install a deformed wheel or tire even if it has been repaired. Such wheels or tires could have structural damage and could fail without warning. ● The use of retread recommended. tires is not ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet. Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance.
● Tire tread of the TEMPORARY USE ONLY spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear. ● Do not use the spare tire on other vehicles. ● Do not use more than one spare tire at the same time. ● Do not tow a trailer when the TEMPORARY USE ONLY spare tire is installed. CAUTION ● Do not use tire chains on a TEMPORARY USE ONLY spare tire. Tire chains will not fit properly and may cause damage to the vehicle.
9 Technical and consumer information Capacities and recommended fuel/lubricants . . . . . . . . . 9-2 Fuel recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Engine oil and oil filter recommendations . . . . . . . . . . 9-5 Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 Engine . . . . . . . . . . . . . . . . . . . . . .
CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Fuel Engine oil *7 Drain and Refill With oil filter change Without oil filter change Cooling system With reservoir Capacity (Approximate) US measure Imp measure 20 gal 16-5/8 gal Liter 75.
FUEL RECOMMENDATION Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). ● Do not use E-85 fuel in your vehicle. Your vehicle is not designed to run on E-85 fuel. Using E-85 fuel can damage the fuel system components and is not covered by the NISSAN new vehicle limited warranty. For 3.
If any driveability problems such as engine stalling and difficult hot-starting are experienced after using oxygenate-blend fuels, immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refueling. Gasoline containing oxygenates can cause paint damage. E–85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel Vehicle (FFV). Do not use E-85 in your vehicle. U.S.
Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be operated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage.
Your engine was filled with a high-quality engine oil when it was built. You do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle.
SPECIFICATIONS ENGINE Model QR25DE VQ35DE Type Gasoline, 4-cycle, DOHC Gasoline, 4-cycle, DOHC Cylinder arrangement 4-cylinder in-line 6-cylinder, V-block, Slanted at 60° Bore x Stroke Displacement Firing order in (mm) 3.5 x 3.9 (89.0 x 100.0) cu in (cm3) 151.82 (2,488) 1–3–4–2 3.760 x 3.205 (95.5 x 81.4) 213.45 (3,498) 1–2–3–4–5–6 Idle speed M/T CVT (in “N” position) No adjustment is necessary. Ignition timing (degree B.T.D.C.
WHEELS AND TIRES Wheel type DIMENSIONS AND WEIGHTS Size Offset Overall length in (mm) Aluminum/Steel 16 x 7JJ 1.77 (45) Overall width in (mm) 70.7(1,795) Aluminum/Steel 17 x 7 1/2JJ 1.77 (45) Overall height in (mm) 57.9(1,471) T type (Spare) 16 x 4T 1.57 (40) Front tread in (mm) 61.0(1,549) P215/60R16 Rear tread in (mm) 61.0(1,549) P215/55R17 Wheelbase in (mm) 109.
WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY VEHICLE IDENTIFICATION When planning to drive your NISSAN vehicle in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available.
WTI0096 QR25DE ENGINE SERIAL NUMBER The number is stamped on the engine as shown. WTI0049 VQ35DE STI0349 F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification label is affixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.
WTI0173 WTI0174 WTI0178 EMISSION CONTROL INFORMATION LABEL TIRE AND LOADING INFORMATION LABEL AIR CONDITIONER SPECIFICATION LABEL The emission control information label is attached to the underside of the hood as shown. The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. The air conditioner specification label is affixed to the underside of the hood as shown.
INSTALLING FRONT LICENSE PLATE VEHICLE LOADING INFORMATION Use the following steps to mount the front license plate: 1 s Make a shallow hole in each plastic finisher at the location mark (small dimple) using a 0.31 in (8 mm) drill. To avoid damaging the threads behind the finisher, apply only light pressure to the drill. 2 s Mount the license plate bracket using two 8 mm slotted hex head screws. WARNING ● It is extremely dangerous to ride in a cargo area inside a vehicle.
INSTALLING FRONT LICENSE PLATE ● GVW (Gross Vehicle Weight) - curb weight plus the combined weight of passengers and cargo. ● GVWR (Gross Vehicle Weight Rating) - maximum total combined weight of the unloaded vehicle, passengers, luggage, hitch, trailer tongue load and any other optional equipment. This information is located on the F.M.V.S.S./C.M.V.S.S. label. ● GAWR (Gross Axle Weight Rating) maximum weight (load) limit specified for the front or rear axle. This information is located on the F.M.V.S.S./C.
INSTALLING FRONT LICENSE PLATE Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity.
INSTALLING FRONT LICENSE PLATE 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
TOWING A TRAILER WARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and performance and may lead to accidents. CAUTION ● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km). Your engine, axle or other parts could be damaged. ● For the first 500 miles (800 km) that you tow a trailer, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.
Temperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automatically decrease engine power. Vehicle speed may decrease under high load. Plan your trip carefully to account for trailer and vehicle load, weather and road conditions.
Towing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load. To determine the Gross Trailer Weight, weigh your trailer on a scale with all equipment and cargo, that are normally in the trailer when it is towed.
TOWING LOAD/SPECIFICATION TOWING LOAD / SPECIFICATION UNIT: lb (kg) MAXIMUM TOWING LOAD MAXIMUM TONGUE LOAD 1,000 (454) 100 (45) TOWING SAFETY Trailer hitch Choose a proper hitch for your vehicle and trailer. A genuine NISSAN trailer hitch is available from your NISSAN dealer (Canada only). Make sure the trailer hitch is securely attached to the vehicle, to help avoid personal injury or property damage due to sway caused by crosswinds, rough road surfaces or passing trucks.
Safety chains Always use suitable safety chains between your vehicle and the trailer. The safety chains should be crossed and should be attached to the hitch, not to the vehicle bumper or axle. Be sure to leave enough slack in the chains to permit turning corners. Trailer lights Trailer lights should comply with federal and/or local regulations. For assistance in hooking up trailer lights, contact a NISSAN dealer or reputable trailer dealer.
● Avoid abrupt starts, acceleration or stops. 5. Shift the transmission into P (Park). ● Avoid sharp turns or lane changes. 6. Turn off the engine. ● Always drive your vehicle at a moderate speed. ● When backing up, hold the bottom of the steering wheel with one hand. Move your hand in the direction in which you want the trailer to go. Make small corrections and back up slowly. If possible, have someone guide you when you are backing up. Always block the wheels on both vehicle and trailer when parking.
Do the following if the trailer begins to sway: 1. Take your foot off the accelerator pedal to allow the vehicle to coast and steer as straight ahead as the road conditions allow. This combination will help stabilize the vehicle - Do not correct trailer sway by steering or applying the brakes. 2. When the trailer sway stops, gently apply the brakes and pull to the side of the road in a safe area. 3. Try to rearrange the trailer load so it is balanced as described earlier in this section.
UNIFORM TIRE QUALITY GRADING Continuously Variable Transmission To tow a vehicle equipped with a continuously variable transmission, an appropriate vehicle dolly MUST be placed under the towed vehicle’s drive wheels. Always follow the dolly manufacturer’s recommendations when using their product. Manual Transmission ● Always tow with the manual transmission in Neutral. ● After towing 500 miles (805 km), start and idle the engine with the transmission in Neutral for two minutes.
WARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat build-up and possible tire failure.
READINESS FOR INSPECTION/ MAINTENANCE (I/M) TEST Due to legal requirements in some states and Canadian Provinces, your vehicle may be required to be in what is called the “ready condition” for an Inspection/Maintenance (I/M) test of the emission control system. The vehicle is set to the “ready condition” when it is driven through certain driving patterns. Usually, the ready condition can be obtained by ordinary usage of the vehicle.
EVENT DATA RECORDERS OWNER’S MANUAL/SERVICE MANUAL ORDER INFORMATION Your vehicle is equipped with a variety of computers that monitor and control a number of systems to optimize performance and help service technicians with diagnosis and repair. Some of the computers monitor emission control systems, braking systems, engine systems, transmission systems, tire pressure systems, and airbag systems. Some data about vehicle operation may be stored in the computers for use during servicing.
Insist on the use of genuine NISSAN collision parts! If you want your vehicle to be restored using parts made to NISSAN’s original exacting specifications – if you want to help it to last and hold its resale value, the solution is simple. Tell your insurance agent and your repair shop to only use Genuine NISSAN Collision Parts. NISSAN does not warrant non-NISSAN parts, nor does NISSAN’s warranty apply to damage caused by a non-genuine part.
MEMO 9-28 Technical and consumer information
10 Index A Active head restraint . . . . . . . . . . . . . . .1-8 Air bag (See supplemental restraint system) . .1-35 Air bag system Front (See supplemental front impact air bag system) . . . . . . . . . . . . . . .1-42 Air bag warning light. . . . . . . . . . .1-50, 2-12 Air cleaner housing filter . . . . . . . . . . . .8-18 Air conditioner Air conditioner operation . . . . . . . . . .4-13 Air conditioner service . . . . . . . . . . .4-20 Air conditioner specification label . . . . .
Cold weather driving . . . . . . . . . . . . . .5-25 Compact disc (CD) player . . . . . . . . . . .4-29 Compass display . . . . . . . . . . . . . . . . .2-6 Console box . . . . . . . . . . . . . . . . . . .2-38 Continuously Variable Transmission (CVT) . .5-10 Continuously Variable Transmission (CVT) fluid . . . . . . . . . . . . . . . . . . . . .8-12 Driving with Continuously Variable Transmission (CVT) . . . . . . . . . . . . .5-10 Control panel buttons Brightness/contrast button . . . . . . . . .
G Garage door opener, HomeLinkT Universal Transceiver . . . . . . . . . . . . . . . . . . Gas cap . . . . . . . . . . . . . . . . . . . . Gauge Engine coolant temperature gauge . . . Fuel gauge . . . . . . . . . . . . . . . . Odometer . . . . . . . . . . . . . . . . . Speedometer . . . . . . . . . . . . . . . Tachometer . . . . . . . . . . . . . . . . Trip odometer . . . . . . . . . . . . . . . General maintenance . . . . . . . . . . . . Glove box . . . . . . . . . . . . . . . . . . . Glove box lock . . . .
Low tire pressure warning light . . . . . .2-11 Low washer fluid warning light . . . . . . .2-21 Passenger air bag and status light. . . . .1-44 Spotlights (See map light) . . . . . . . . .2-46 Trunk light . . . . . . . . . . . . . . . . . .2-46 Warning/indicator lights and audible reminders . . . . . . . . . . . . . . . . . . .2-9 Lights Map lights . . . . . . . . . . . . . . . . . .2-46 Lock Child safety rear door lock . . . . . . . . . .3-5 Door locks . . . . . . . . . . . . . . . . . .
Readiness for inspection maintenance (I/M) test. . . . . . . . . . . . . . . . . . . . Rear power windows . . . . . . . . . . . . . Rear seat . . . . . . . . . . . . . . . . . . . Rear view monitor . . . . . . . . . . . . . . Rear window and outside mirror defroster switch . . . . . . . . . . . . . . . . . . . . . Recorders Event data . . . . . . . . . . . . . . . . . Refrigerant recommendation . . . . . . . . Registering your vehicle in another country. Reporting safety defects (US only) . . . . . .9-25 .
Theft (NISSAN vehicle immobilizer system), engine start . . . . . . . . . . . . . . . . . . .2-24 Three-way catalyst . . . . . . . . . . . . . . . .5-2 Tire Flat tire . . . . . . . . . . . . . . . . . . . .6-2 Spare tire. . . . . . . . . . . . . . . .6-3, 8-41 Tire chains . . . . . . . . . . . . . . . . . .8-38 Tire placard . . . . . . . . . . . . . . . . .9-11 Tire pressure . . . . . . . . . . . . . . . .8-31 Tire rotation . . . . . . . . . . . . . . . . .8-39 Types of tires . . . . . . . . . . . . . . . .
MEMO
MEMO
MEMO
MEMO
MEMO
MEMO
GAS STATION INFORMATION RECOMMENDED FUEL: For 2.5L engine Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). For 3.5L engine NISSAN recommends the use of premium unleaded gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96).
QUICK REFERENCE 1. Engine coolant 8-8 2. Window washer fluid 8-14 3. Engine oil 8-9 4. Passenger supplemental front impact air bag 1-35 5. Audio system 4-20; Air conditioner 4-10, 4-18 6. Supplemental side-impact air bag 1-35 7. Front seats 1-2 8. Spare tire 6-2 9. Fuel recommendation 9-3 10. Keys 3-2 11. Supplemental side-impact air bag 1-35 12. Seat belts 1-9 13. Fuel-filler door release 3-19 14. Supplemental curtain side-impact air bag 1-35 15.