2008 Armada Owner's Manual (Click here to view this publication.) In addition to the Owner's Manual, a Voice Recognition system supplement publication may pertain to your vehicle. Compare the VIN (vehicle identification number) information found on your vehicle's VIN plate to the VIN information below to determine applicability. The VIN plate is located on top of the instrument panel, on the driver's side of your vehicle.
FOREWORD READ FIRST—THEN DRIVE SAFELY Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. Before driving your vehicle please read this Owner’s Manual carefully. This will ensure familiarity with controls and maintenance requirements, assisting you in the safe operation of your vehicle.
WHEN READING THE MANUAL MODIFICATION OF YOUR VEHICLE This vehicle should not be modified. Modification could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from modifications may not be covered under NISSAN warranties. This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle.
CALIFORNIA PROPOSITION 65 WARNING WARNING Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
NISSAN CUSTOMER CARE PROGRAM NISSAN CARES . . . Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs.
Table of Contents Illustrated table of contents 0 Safety—Seats, seat belts and supplemental restraint system 1 Instruments and controls 2 Pre-driving checks and adjustments 3 Monitor, climate, audio, phone and voice recognition systems 4 Starting and driving 5 In case of emergency 6 Appearance and care 7 Maintenance and do-it-yourself 8 Technical and consumer information 9 Index 10
0 Illustrated table of contents Airbags, seat belts and child restraints . . . . . . . . . . . . . . . 0-2 Exterior front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-3 Exterior rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-4 Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5 Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-6 Engine compartment check locations . . . .
AIRBAGS, SEAT BELTS AND CHILD RESTRAINTS 1. 2. 3. 3rd row bench seat belts (P. 1-16) 2nd row seat belts (P. 1-16) Roof-mounted curtain side-impact and rollover supplemental air bags (P. 1-48) 4. Front seat belts (P. 1-16) 5. Supplemental front-impact air bags (P.1-48) 6. Seats (P. 1-2) 7. Occupant classification sensor (pressure sensor) (P.1-55) 8. Seat belts with pretensioners (P. 1-62) 9. Front seat-mounted side-impact supplemental air bags (if so equipped) (P. 1-48) 10.
EXTERIOR FRONT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Engine hood (P. 3-20) Windshield wiper and washer switch (P. 2-30) Windshield (P. 8-19) Power windows (P. 2-53) Door locks, keyfob, keys (P. 3-4, 3-6, 3-2) Mirrors (P. 3-29) Tire pressure (P. 9-12) Flat tire (P. 6-2) Tire chains (P. 8-40) Replacing bulbs (P. 8-31) Headlight and turn signal switch (P. 2-32) Fog light switch (P. 2-35) Tow hooks (if so equipped) (P. 6-14) See the page number indicated in parentheses for operating details.
EXTERIOR REAR 1. 2. 3. 4. 5. 6. 7. Roof rack (P. 2-52) Vehicle loading (P. 9-13) Glass hatch (P. 3-25) Rear window washer (P.2-31) Glass hatch release (P.3-25) Lift gate release (P. 3-23) Rearview monitor (if so equipped) (P.4-34) 8. Replacing bulbs (P. 8-31) 9. Fuel-filler cap, fuel recommendation (P. 3-25, P. 9-3, 9-4) 10. Fuel-filler door (P. 3-25) 11. Child safety rear door locks See the page number indicated in parentheses for operating details.
PASSENGER COMPARTMENT 1. 2. 3. Rear ventilators (P. 4-37) Storage (P. 2-42) DVD entertainment system (if so equipped) (P. 4-78) 4. Sunroof (if so equipped) (P. 2-56) 5. Map lights (P. 2-59) 6. Sun visors (P. 3-28) 7. HomeLinkT (P. 2-60) 8. Glove box (P. 2-42) 9. Seats (P. 1-2) 10. Cup holders (P. 2-46) 11. Luggage storage (P. 2-50) See the page number indicated in parentheses for operating details.
INSTRUMENT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. WIC1256 14. 15. Vents (P. 4-37) Headlight/fog light (if so equipped)/turn signal switch (P. 2-32) Instrument brightness control (P. 2-35) Steering wheel switch for audio control/hands-free bluetoothT phone (P. 4-75) Driver supplemental air bag/horn (P. 1-48, P. 2-36) Meters, gauges and warning/indicator lights (P. 2-4, 2-13) Cruise control main/set switches (P. 5-17) Windshield wiper/washer switch and rear window wiper/washer switch (P. 2-30, P.
16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. Climate controls (P. 4-38) Power outlet/cigarette lighter (accessory) (P. 2-40/P. 2-41) Heated seat switch (if so equipped) (P. 2-37) Vehicle dynamic control (VDC) off switch (P. 2-38) Tow mode switch (P. 2-40) Shift selector lever (P. 5-12) Heated steering wheel (if so equipped) (P. 2-37) Center stack storage (P. 2-42) Power outlet (P. 2-40) Front passenger air bag status light (P. 1-57) Auxiliary jack (P.
ENGINE COMPARTMENT CHECK LOCATIONS 1. 2. 3. 4. 5. 6. Battery (P. 8-13) Fuse/fusible link box (P. 8-22) Transmission dipstick (P. 8-11) Engine oil filler cap (P. 8-8) Brake fluid reservoir (P. 8-12) Windshield washer fluid reservoir (P. 8-12) 7. Air cleaner (P. 8-17) 8. Drive belt location (P.8-15) 9. Radiator cap (P. 8-7) 10. Power steering fluid reservoir (P. 8-11) 11. Engine oil dipstick (P. 8-8) 12. Engine coolant reservoir (P. 8-7) See the page number indicated in parentheses for operating details.
WARNING/INDICATOR LIGHTS Warning light or Name Page Anti-lock Braking System (ABS) warning light 2-14 Automatic transmission check warning light 2-14 Automatic transmission park warning light ( model) 2-14 Brake warning light 2-14 or Charge warning light 2-15 Check suspension warning light (if so equipped) 2-15 Warning light Name Page Engine oil pressure low/engine coolant temperature high warning light 2-15 4WD warning light ( model) 2-16 Low fuel warning light 2-16 Low tire pres
MEMO 0-10 Illustrated table of contents
1 Safety—Seats, seat belts and supplemental restraint system Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front manual seat adjustment — passenger’s side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front power seat adjustment (for driver’s seat and if so equipped for passenger’s seat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 2nd row captain’s chair adjustment (if so equipped) . . . . . .
SEATS FRONT MANUAL SEAT ADJUSTMENT — PASSENGER’S SIDE ARS1152 WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. ● For the most effective protection when the vehicle is in motion, the seat should be upright.
LRS0244 LRS0245 Forward and backward Reclining Pull the lever up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. To recline the seatback, pull the lever up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position.
The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit (see “Precautions on seat belt usage” later in this section). Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the transmission is in P (Park).
LRS0634 LRS0635 Seat lifter (driver’s seat) Lumbar support (driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion. The lumbar support feature provides lower back support to the driver. Move the lever up or down to adjust the seat lumbar area. WRS0369 2ND ROW CAPTAIN’S CHAIR ADJUSTMENT (if so equipped) Reclining To recline the seatback, pull up on the lever and lean back.
WRS0415 Tip up for easy entry to the 3rd row The 2nd row captain’s chairs can be tipped forward for easy entry or exit from the 3rd row bench 1 raise the armrest so seat. To enter the 3rd row s it is parallel to the seatback and in the stowed position, then lift up on the latch located on the upper corner of the seatback on the 2nd row captain’s chair and fold the seatback forward at an angle over the seat base. This will release the back of the seat so it may be tipped forward.
WARNING ● After adjustment, gently rock in the seat to make sure it is securely locked. ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. You could also slide under the lap belt and receive serious internal injuries. ● For the most effective protection when the vehicle is in motion, the seat should be upright.
WARNING Head restraints should be adjusted properly as they may provide significant protection against injury in an accident. Do not remove them. Check the adjustment after someone else uses the seat. LRS0286 HEAD RESTRAINT ADJUSTMENT To raise the head restraint, pull it up. To lower, push and hold the lock knob and push the head restraint down. WRS0134 Adjust the head restraint so the center is level with the center of your ears. The head restraints on the 2nd and 3rd row seats are removable.
● Do not attach anything to the head restraint stalks. Doing so could impair Active Head Restraint function. The Active Head Restraint moves forward utilizing the force that the seatback receives from the occupant in a rear-end collision. The movement of the head restraint helps support the occupant’s head by reducing its backward movement and helping absorb some of the forces that may lead to whiplash type injuries.
FLEXIBLE SEATING WARNING ● Never allow anyone to ride in the cargo area or on the rear seats when they are in the fold-down position. In a collision, people riding in these areas without proper restraints are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly.
WARNING ● If you fold the front passenger’s seatback flat forward to carry longer objects, be sure this cargo is properly secured and not near an air bag. In a crash, an inflating air bag might force that object toward a person. This could cause severe injury or even death. Secure objects away from the area in which an air bag would inflate. See “Precautions on supplemental restraint system” later in this section.
LRS0333 s 3 Then lift up on the recline lever to fold the seatback flat forward. LRS0334 s 4 There is a carpet panel flap that can be folded toward the back of the vehicle. LRS0641 s 5 The carpet panel flaps provide a level cargo floor when the 3rd row seats are also folded flat. Reverse this process to return the 2nd row captain’s chairs to a seating position. Make sure to properly raise the seatback to an upright position and push the seat cushion down into place.
LRS0336 Folding the 2nd row bench seat (if so equipped) To fold the 2nd row bench seat flat for maximum cargo hauling: 1 s Pull the strap forward, located in the center of each seat cushion, and fold each seat cushion toward the front of the vehicle. LRS0337 s 2 Then lift up on the recline lever on the side of the outboard seats to fold the outboard seatbacks flat.
To return the 3rd row split bench seat to a seating position unfold the seatback and push it back until it latches into position. WARNING ● When returning the seatbacks, be sure to attach the rear center seat belt connector. ● Do not unfasten the rear center seat belt connector except when folding down the rear seat. LRS0636 s 4 The carpet panel flap provides a level cargo floor when the 3rd row seats are also folded flat. 5.
● Disconnect and secure the center seatbelt and tongues into the retractor base. See “Stowing the 3rd row center seatbelt” later in this section. – Always reconnect the center seatbelt when the seat is returned to the upright position ● Make sure that there are no objects on the seatback cushion.
SEAT BELTS If the ignition is off, the power folding seats are always operational. If the ignition is on, the power folding seats are only operational when the transmission is in P (Park) or N (Neutral). If the engine is started during operation, the seat(s) will temporarily pause. NOTE: Operating the power folding seats can discharge the vehicle battery if the vehicle is not running.
SSS0134 WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained in the rear seat and, if appropriate, in a child restraint. SSS0016 WARNING ● The seat belt should be properly adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident. Serious injury or death can occur if the seat belt is not worn properly.
● Be sure the seat belt tongue is securely fastened to the proper buckle. ● Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness. ● Do not allow more than one person to use the same seat belt. ● Never carry more people in the vehicle than there are seat belts. SSS0014 WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never run the belt behind your back, under your arm or across your neck.
There are three basic types of child restraint systems: ● Rear facing child restraint ● Front facing child restraint ● Booster seat The proper restraint depends on the child’s size. Generally, infants up to about 1 year and less than 20 pounds (9 kg) should be placed in rear facing child restraints. Front facing child restraints are available for children who outgrow rear facing child restraints and are at least 1 year old.
have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards. Once the child has grown so the shoulder belt is no longer on or near the face and neck, use the shoulder belt without the booster seat. WARNING Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving. The child could be seriously injured or killed in an accident or sudden stop.
Once retracted, the seat belt is in the Emergency Locking Retractor (ELR) mode. See “Child restraints” later in this section for more information. The ALR should be used only for child restraint installation. During normal seat belt use by a passenger, the locking mode should not be activated. If it is activated it may cause uncomfortable seat belt tension. It can also change the operation of the front passenger air bag. See “Front passenger air bag and status light” later in this section.
● Grasp the shoulder belt and pull forward quickly. The retractor should lock and restrict further belt movement. If the retractor does not lock during this check or if you have any questions about seat belt operation, see a NISSAN dealer. WRS0139 SSS0240 Unfastening the seat belts Center of the 3rd row bench seat s The 3rd row center seat belt has a connector 1 and a seat belt tongue s 2 .
Stowing the 3rd row center seat belt When folding down the 3rd row seat, the 3rd row center seat belt can be retracted into a stowed position as follows: 1 s 2 s 3 s SSS0241 WARNING ● Always fasten the connector tongue and the seat belt in the order shown. Hold the connector tongue so that the seat belt does not retract suddenly when the tongue is released from the connector buckle. Release the connector tongue by inserting a suitable tool such as a key into the A.
Attaching the 3rd row center seat belt ● If the rear center seat belt connector and the seatbacks are not secured in the correct position, serious personal injury may result in an accident or sudden stop. Always be sure the 3rd row center seat belt connector tongue and connector buckle are attached. Disconnect only when folding down the rear seat. To connect the buckle: 1 s Pull out the connector tongue from the retractor base. 2 s Pull out the seat belt tongue from the fabric sleeve.
● When attaching the rear center seat belt connector, be certain that the seatbacks are completely secured in the latched position and the rear center seat belt connector is completely secured. WARNING ● After adjustment, release the adjustment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position. ● The shoulder belt anchor height should be adjusted to the position best for you.
CHILD RESTRAINTS SEAT BELT EXTENDERS If, because of body size or driving position, it is not possible to properly fit the lap-shoulder belt and fasten it, an extender is available which is compatible with the installed seat belts. The extender adds approximately 8 inches (200 mm) of length and may be used for either the driver or front passenger seating position. See a NISSAN dealer for assistance if an extender is required.
● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An inflating supplemental front air bag could seriously injure or kill your child. A rearfacing child restraint must only be used in the rear seat. WRS0256 WARNING ● Infants and small children should always be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can result in serious injury or death.
● When your child restraint is not in use, keep it secured with the LATCH System or a seat belt to prevent it from being thrown around in case of a sudden stop or accident. CAUTION Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint. This vehicle is equipped with a universal child restraint lower anchor system, referred to as the Lower Anchors and Tethers for CHildren System or LATCH.
WRS0416 LATCH system anchor locations – bench seat ● 2nd row bench seat outboard positions only (if so equipped). LRS0344 LATCH label locations 2nd row captain’s chairs (if so equipped) LATCH lower anchor point locations The LATCH anchors are located at the rear of the seat cushion near the seatback. A label is attached to the seatback to help you locate the LATCH anchors.
LRS0748 LRS0661 LATCH lower anchor location LATCH webbing-mounted attachment ● Child restraint anchor points are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstance are they to be used for adult seat belts or harnesses. Installing child restraint LATCH anchor attachments LATCH compatible child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle.
TOP TETHER STRAP CHILD RESTRAINT If the manufacturer of your child restraint requires the use of a top tether strap, it must be secured to the anchor point. WARNING ● 3rd row bench seat on the floor of the cargo area behind the center seat position as shown. If you have any questions when installing a top tether strap child restraint on the rear seat, consult your NISSAN dealer for details.
LRS0340 2nd row captain’s chairs (if so equipped) 2nd row captain’s chairs or bench seat (if so equipped) 1. Top tether strap 2. Anchor point For the 2nd row captain’s chairs or bench seat (if so equipped), install the top tether strap as follows: 1. Raise the head restraint. LRS0361 2nd row bench seat (if so equipped) 3. Secure the tether strap to the tether anchor point on the seat directly behind the child restraint. 4.
The center position of the 3rd row bench seat is the seating position that can use a top tether strap. For the 3rd row bench seat, install the top tether strap as follows: 1. Position the top tether strap over the top of the center seating position seatback. 2. Secure the tether strap to the tether anchor point on floor behind the child restraint. 3. Tighten the tether strap according to the manufacturer’s instructions to remove any slack.
LRS0663 Front facing web-mounted – step 3 3. Secure the child restraint anchor attachments to the LATCH lower anchors. LRS0664 Front facing rigid-mounted – step 3 with the proper child restraint fit, try another seating position or a different child restraint. 4. Return the seatback to its normal upright and locked position. The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit.
8. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 4 through 7. Rear-facing Follow these steps to install a rear-facing child restraint in the 2nd row seats using LATCH: 1. Recline the seatback if the seatback is adjustable to assist in attaching the child restraint to the lower anchors. WRS0697 Front facing – step 7 7.
LRS0666 LRS0673 Rear facing rigid-mounted – step 3 Rear facing – step 5 5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attachments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments. 6.
● NISSAN recommends that child restraints be installed in the rear seat. However, if you must install a forward facing child restraint in the front passenger seat, move the passenger seat to the rearmost position. Also, be sure the front passenger air bag status light is illuminated to indicate the passenger air bag is OFF. See “Front passenger air bag and status light” later in this section for details.
2. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. See “Head restraint adjustment” in this section. WRS0699 Front-facing (front passenger seat) – step 1 If the head restraint is removed, store it in a secure place.
LRS0667 Front facing – step 4 4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor mode (child restraint mode). It reverts to emergency locking retractor mode when the seat belt is fully retracted. LRS0668 Front facing – step 5 5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0681 Front facing – step 6 6.
8. Before placing the child in the child restraint, hold the child restraint near the seat belt path and use force to push the child restraint from side to side, and tug it forward to make sure that it is securely held in place. It should not move more than 1 in (25 mm). If it does move more than 1 in (25 mm), pull again on the shoulder belt to further tighten the child restraint.
WRS0256 Rear-facing – step 1 Rear-facing Follow these steps to install a rear-facing child restraint using the vehicle seat belt in the rear seats: 1. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat. Position the child restraint on the seat. Always follow the restraint manufacturer’s instructions. WRS0761 Rear facing – step 2 2.
LRS0670 Rear facing – step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0762 Rear facing – step 5 5. Remove any additional slack from the child restraint; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seatback while pulling up on the seat belt. WRS0763 Rear facing – step 6 6.
BOOSTER SEATS 7. Check that the retractor is in the Automatic Locking Retractor mode by trying to pull more seat belt out of the retractor. If you cannot pull any more seat belt webbing out of the retractor, the retractor is in the Automatic Locking Retractor mode ● Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe accident. The child could be crushed between the adult and parts of the vehicle.
● Do not use towels, books, pillows or other items in place of a booster seat. Items such as these may move during normal driving or a collision and result in serious injury or death. Booster seats are designed to be used with a lap/shoulder belt. Booster seats are designed to properly route the lap and shoulder portions of the seat belt over the strongest portions of a child’s body to provide the maximum protection during a collision.
BOOSTER SEAT INSTALLATION WARNING NISSAN recommends that booster seats be installed in the rear seat. However, if you must install a booster seat in the front passenger seat, move the passenger’s seat to the rearmost position. CAUTION LRS0453 LRS0464 ● Make sure the child’s head will be properly supported by the booster seat or vehicle seat. The seat back must be at or above the center of the child’s ears.
WRS0534 WRS0699 1. If you must install a booster seat in the front seat, move the seat to the rearmost position. Rear center position 2. Position the booster seat on the seat. Only place it in a front facing direction. Always follow the booster seat manufacturer’s instructions. WRS0533 Rear outboard position 3. The booster seat should be positioned on the vehicle seat so that it is stable. If necessary, adjust or remove the head restraint to obtain the correct booster seat fit.
4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to follow the booster seat manufacturer’s instructions for adjusting the belt routing. 5. Pull the shoulder belt portion of the seat belt toward the retractor to take up extra slack. Be sure the shoulder belt is positioned across the top, middle portion of the child’s shoulder. Be sure to follow the booster seat manufacturer’s instructions for adjusting the belt routing. LRS0454 Front passenger position 6.
SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System (SRS) section contains important information concerning the driver and passenger supplemental front air bags (NISSAN Advanced Air Bag System), front seat-mounted side-impact supplemental air bags, roof-mounted curtain side-impact and rollover supplemental air bag and pretensioner seat belts.
the seatback and as far away as practical from the steering wheel or instrument panel. Always use the seat belts. ● The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The advanced air bag system monitors the severity of a collision and seat belt usage then inflates the air bags. Failure to properly wear seat belts can increase the risk or severity of injury in an accident.
ARS1133 ARS1041 WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.
ARS1042 ARS1043 ARS1044 WARNING ● Children may be severely injured or killed when the supplemental front air bags, front seat-mounted side-impact supplemental airbags and roofmounted curtain side-impact and rollover supplemental airbags inflate if they are not properly restrained. Preteens and children should be properly restrained in the rear seat, if possible.
ARS1045 WRS0431 WRS0256 WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An inflating supplemental front air bag could seriously injure or kill your child. See “Child restraints” earlier in this section for details. Do not lean against the door.
● The front seat-mounted side-impact supplemental air bags and roofmounted curtain side-impact and rollover supplemental air bags ordinarily will not inflate in the event of a frontal impact, rear impact, or lower severity side collision. Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents. WRS0365 Do not lean against doors or windows. SSS0162 Do not lean against doors or windows.
WARNING ● The seat belts, the front seat-mounted side-impact supplemental air bags and roof-mounted curtain side-impact and rollover supplemental air bags are most effective when you are sitting well back and upright in the seat. The front seatmounted side-impact supplemental air bags and roof-mounted curtain sideimpact and rollover supplemental air bags inflate with great force.
1. Roof-mounted curtain side-impact and rollover supplemental air bag modules 2. Roof-mounted curtain side-impact and rollover supplemental air bags 3. Air bag Control Unit (ACU) 4. Supplemental front air bag modules 5. Crash zone sensor 6. Occupant classification system control unit 7. Occupant classification sensor (pressure sensor) 8. Seat belt buckle switches 9. Pretensioner 10. Satellite sensors 11.
The driver supplemental front air bag is located in the center of the steering wheel. The passenger supplemental front air bag is mounted in the dashboard above the glove box. The supplemental front air bags are designed to inflate in higher severity frontal collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions.
Status light is The front passenger air bag status light located under the climate controls. The light operates as follows: ● Unoccupied passenger’s seat: The is OFF and the front passenger air bag is OFF and will not inflate in a crash. ● Passenger’s seat occupied by a small adult, child or child restraint as outlined in this illuminates to indicate section: The that the front passenger air bag is OFF and will not inflate in a crash.
Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes his/her weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position), this could cause the sensor to turn the air bag OFF.
Other supplemental front air bag precautions WARNING ● Do not place any objects on the steering wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel. Such objects may become dangerous projectiles and cause injury if the supplemental front air bag inflates. ● Immediately after inflation, several front air bag system components will be hot. Do not touch them; you may severely burn yourself.
The front seat-mounted side-impact supplemental air bags and roof-mounted curtain sideimpact and rollover supplemental air bags are designed to inflate in higher severity side collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions.
occupant is too close to, or is against, these air bag modules during inflation. The front seatmounted side-impact supplemental air bag will deflate quickly after the collision is over. The roof-mounted curtain side-impact and rollover supplemental air bag will remain inflated for a short time. The front seat-mounted side-impact supplemental air bags and roof-mounted curtain side-impact and rollover supplemental air bags operate only when the ignition switch is in the ON or START positions.
* The SRS wiring harness or connectors are yellow or orange for easy identification. When selling your vehicle, we request that you inform the buyer about the front seat-mounted side-impact supplemental air bags and roofmounted curtain side-impact and rollover supplemental air bag system and guide the buyer to the appropriate sections in this Owner’s Manual. Seat belts with pretensioners (Front seats) WARNING ● The seat belts with pretensioners cannot be reused after activation.
SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental front air bags, front seat-mounted side-impact supplemental air bags and roof-mounted curtain sideimpact and rollover supplemental air bag systems are placed in the vehicle as shown in the illustration. LRS0397 1. SRS Air bag warning labels The warning labels are located on the surface of the sun visor. 2.
When the ignition key is in the ON or START position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the supplemental front air bag, front seat-mounted side-impact supplemental air bags, roofmounted curtain side-impact, rollover supplemental air bag and pretensioner seat belt systems need servicing: ● The supplemental air bag warning light remains on after approximately 7 seconds.
● If you need to dispose of the supplemental air bag, seat belts with pretensioners or scrap the vehicle, contact a NISSAN dealer. Correct supplemental air bag and seat belts with pretensioners disposal procedures are set forth in the appropriate NISSAN Service Manual. Incorrect disposal procedures could cause personal injury.
2 Instruments and controls Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-5 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Engine coolant temperature gauge . . . . . . . . . . . . . . . 2-6 Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44 Sunglasses holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-44 Map pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45 Seatback pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45 Overhead console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45 Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. WIC1256 14. 15. Vents (P. 4-37) Headlight/fog light (if so equipped)/turn signal switch (P. 2-32) Instrument brightness control (P. 2-35) Steering wheel switch for audio control/hands-free bluetoothT phone (P. 4-75) Driver supplemental air bag/horn (P. 1-48, P. 2-36) Meters, gauges and warning/indicator lights (P. 2-4, 2-13) Cruise control main/set switches (P. 5-17) Windshield wiper/washer switch and rear window wiper/washer switch (P. 2-30, P.
16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. Climate controls (P. 4-38) Power outlet/cigarette lighter (accessory) (P. 2-40/P. 2-41) Heated seat switch (if so equipped) (P. 2-37) Vehicle dynamic control (VDC) off switch (P. 2-38) Tow mode switch (P. 2-40) Shift selector lever (P. 5-12) Heated steering wheel (if so equipped) (P. 2-37) Center stack storage (P. 2-42) Power outlet (P. 2-40) Front passenger air bag status light (P. 1-57) Auxiliary jack (P.
METERS AND GAUGES WIC1243 1. 2. 3. 4. 5. 6. Warning/indicator lights Tachometer Engine coolant temperature gauge Voltmeter Fuel gauge Speedometer 7. 8. 9.
WIC1244 1. 2. 3. Speedometer Odometer/twin trip display Change button SPEEDOMETER AND ODOMETER The odometer records the total distance the vehicle has been driven. The twin trip odometer records the distance of individual trips. WIC1245 Changing the display: Pushing the change button changes the display as follows: Trip → Trip → Odometer only Speedometer Resetting the trip odometer: The speedometer indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h).
CAUTION If the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” in the “In case of emergency” section for immediate action required. WIC1246 TACHOMETER The tachometer indicates engine speed in revolutions per minute (rpm).
indicates that the fuel-filler door is The located on the driver’s side of the vehicle. CAUTION ● If the vehicle runs out of fuel, malfunction indicator light the (MIL) may come on. Refuel as soon as possible. After a few driving trips, the light should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer. LIC1199 FUEL GAUGE The gauge indicates the approximate fuel level in the tank.
● If the gauge needle does not move with the proper amount of engine oil, have the vehicle checked by a NISSAN dealer. Continued vehicle operation in such a condition could cause serious damage to the engine. LIC1136 VOLTMETER When the ignition key is turned to the ON position, the voltmeter indicates the battery voltage. When the engine is running, it indicates the generator voltage. While cranking the engine, the volts drop below the normal range.
COMPASS AND OUTSIDE TEMPERATURE DISPLAY CAUTION ● This gauge is not designed to indicate low automatic transmission fluid level. Use the dipstick to check the fluid level. (See “5-speed automatic transmission fluid” in the “Maintenance and do-ityourself” section.) ● If the gauge indicates automatic transmission fluid temperature over the normal range, stop the vehicle as soon as safely possible. Have the vehicle checked by a NISSAN dealer.
● When the outside temperature is between 140°F (60°C) and 194°F (90°C), the display will read 140°F (60°C). When the temperature is above 194°F (90°C), the display will read “SC”. ● When the outside temperature is between -40°F (-40°C) and -60°F (-51°C), the display will read -40°F (-40°C). When the temperature is below -60°F (-51°C), the display will read “OC”.
Zone variation change procedure The difference between magnetic north and geographical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens: 1. Press and hold the button for about 8 seconds. The current zone number will appear in the display. Release the button. 2. Find your current location on the zone map. Refer to the illustration. 3.
2. Calibrate the compass by driving the vehicle one and a half circles at a maximum speed of 6 MPH (10 km/h). 3. After completing the circles, the display should return to normal. ● If the compass deviates from the correct indication soon after repeated adjustment, have the compass checked at an authorized NISSAN dealer. ● When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner.
WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS or Anti-lock Braking System (ABS) warning light 4WD warning light ( Automatic transmission check warning light High beam indicator light (Blue) Low fuel warning light Malfunction indicator light (MIL) Automatic transmission park warning light model) ( Low tire pressure warning light Security indicator light or Master warning light Slip indicator light Charge warning light Seat belt warning light and chime Turn signal/hazard indicator lights Che
or Anti-lock Braking System (ABS) warning light When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational. If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock function is turned off.
2. If the brake fluid level is correct, have the warning system checked by a NISSAN dealer. WARNING ● Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous.
● If the gauge indicates engine coolant temperature over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” in the “In case of emergency” section for immediate action required. 4WD warning light ( model) The 4WD warning light comes on when the key switch is turned to ON. It turns off soon after the engine is started.
TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure. For additional information, see “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” section and in the “In case of emergency” section. TPMS malfunction: If the TPMS is not functioning properly, the low tire pressure warning light will flash for approximately 1 minute when the ignition switch is placed in the ON position. The light will remain on after the 1 minute.
The seat belt warning light may also illuminate if the front passenger’s seat belt is not fastened when the front passenger’s seat is occupied . For 7 seconds after the ignition switch is in the ON position, the system does not activate the warning light for the front passenger. Refer to “Seat belts” in the “Safety—Seats, seat belts and supplemental restraint system” section for precautions on seat belt usage.
and that the vehicle has at least 3 gallons (11.4 liters) of fuel in the fuel tank. After a few driving trips, the light should turn off if no other potential emission control system malfunction exists. If this indicator light comes on steady for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/maintenance test.
VEHICLE INFORMATION DISPLAY Vehicle dynamic control off indicator light AUDIBLE REMINDERS Brake pad wear warning This indicator light comes on when the vehicle dynamic control off switch is pushed to OFF, the transfer case is in the 4LO position ( model), or when the vehicle dynamic control system is not functioning properly. This indicates the vehicle dynamic control system is not operating. The disc brake pads have audible wear warnings.
The icons at the bottom of the display screen show the options available: ENTER — Press the INFO button to select a highlighted option. NEXT — Rotate the INFO button to highlight an option. WIC1249 HOW TO USE THE VEHICLE INFORMATION DISPLAY Press the vehicle information display INFO but1 located on the instrument panel to toggle ton s through the following modes (if so equipped).
LIC1097 WIC1266 LIC1095 Average speed mode (If so equipped) Time/Miles (km) mode (if so equipped) Range mode (If so equipped) The average speed mode can be selected display the average miles per gallon and miles per hour since the last reset. The time/miles (km) mode can be selected to show the time and distance driven since the last reset. The range mode can be selected to give you an estimation of the distance that can be driven before refueling.
LIC1162 WIC1163 WIC1164 Setting mode (If so equipped) Reset mode (If so equipped) Maintenance mode (If so equipped) The setting mode allows you to set reminders or preferences for maintenance intervals or language displays. The reset mode can be selected in any screen that allows for preferences to be programmed. Once the screen is selected, you have the option to reset their selected distances or time to a new setting.
WIC1165 WIC1166 Display mode (If so equipped) Warning mode The LANGUAGE/UNIT screen will appear when selecting the “Language/Unit” key and pressing the INFO button. The warning mode can be selected to view any warnings that may be present. Once the screen is selected you have the option of skipping the warning or viewing it in detail. Language: English or French Unit: US — mile, °F, MPG Metric — km, °C, L/100 km You can select the language and unit by rotating, then pressing the INFO button.
WIC1185 Vehicle information display warnings and indicators 4. Low windshield washer fluid warning 9. Cruise set switch indicator 5. No key warning 10. Intelligent Key battery discharge indicator 1. Door and liftgate open warning 6. Parking brake warning 11. 4LO indicator ( 2. Lock warning 7. Shift P warning 12. 4WD indicator ( 8. Cruise main switch indicator 13. Automatic transmission position indicator 3.
Door and liftgate open warning No key warning SHIFT P warning This warning illuminates when a door, the liftgate or the liftgate glass has been opened when the engine is running. This warning illuminates following two conditions: This warning illuminates when the ignition switch is in the ACC or OFF position and the shift selector lever is in any position other than (Park) position. Also, a chime sounds when the ignition switch is in the OFF position.
SECURITY SYSTEMS Intelligent Key battery discharge indicator This indicator illuminates when the Intelligent Key battery is running out of power. The indicator may blink while shifting from one drive mode to the other. 4WD indicator ( model) If this indicator illuminates, replace the battery with a new one. See “Intelligent Key battery” in the “Maintenance and do-it-yourself” section. While the engine is running, the 4WD shift indicator will illuminate the position selected by the 4WD shift switch.
brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible. Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment.
The alarm is activated by: ● opening a door without using the key, a request switch, keyfob or Intelligent Key (even if the door is unlocked by using the inside lock knob or the power door lock switch). How to stop an activated alarm The alarm stops only by unlocking the driver’s door with the key, pressing the button on the keyfob or Intelligent Key, or by unlocking all doors with any request switch (Intelligent Key models).
WINDSHIELD WIPER AND WASHER SWITCH NOTE: You can turn on or turn off the driving speed dependent intermittent wiper function (if so equipped). Refer to “Comfort & convenience settings” in the “Display screen, heater, air conditioner and audio systems” section later in this manual. 2 s 3 s LIC0965 SWITCH OPERATION The windshield wiper and washer operates when the ignition switch is in the ON position.
REAR WINDOW WIPER AND WASHER SWITCH REAR WINDOW AND OUTSIDE MIRROR DEFROSTER SWITCH WARNING In freezing temperatures the washer solution may freeze on the window and obscure your vision. Warm the rear window with the defroster before you wash the rear window. CAUTION ● Do not operate the washer continuously for more than 30 seconds. ● Do not operate the washer if the reservoir tank is empty. LIC0966 The rear window wiper and washer operate when the ignition switch is in the ON position.
HEADLIGHT AND TURN SIGNAL SWITCH HEADLIGHT CONTROL SWITCH Lighting 1 s When turning the switch to the position, the front parking, tail, license plate and instrument panel lights come on. 2 s When turning the switch to the position, the headlights come on and all the other lights remain on. CAUTION WIC1186 Type A WIC1250 Use the headlights with the engine running to avoid discharging the vehicle battery.
NOTE: Autolight activation sensitivity and the time delay for autolight shutoff can be adjusted. See “Comfort and convenience settings” in the “Monitor, climate, audio, phone and voice recognition systems(section later in this manual. To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi1 . tion s 2. Turn the ignition key to ON. WIC1251 Autolight system The autolight system allows the headlights to be set so they turn on and off automatically.
After the headlights automatically turn off with the or position, headlight switch in the the headlights will illuminate again for 5 minutes if the headlight switch is moved to the OFF position and then turned to the or position. CAUTION WARNING When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
LIC1159 WIC1253 WIC1254 INSTRUMENT BRIGHTNESS CONTROL TURN SIGNAL SWITCH FOG LIGHT SWITCH (if so equipped) The instrument brightness control operates when the headlight control switch is in the , or AUTO position (with autolights activated). Turn signal 1 s To turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the position. Turn the control to adjust the brightness of instrument panel lights when driving at night.
HAZARD WARNING FLASHER SWITCH HORN ● Turn signals do not work when the hazard warning flasher lights are on. The flashers will operate with the ignition switch in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving. LIC0394 LIC0604 Push the switch on to warn other drivers when you must stop or park under emergency conditions. All turn signal lights flash. To sound the horn, push the center pad area of the steering wheel.
HEATED SEAT (if so equipped) HEATED STEERING WHEEL (if so equipped) CAUTION ● Do not use the seat heater for extended periods or when no one is using the seat. ● Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated. ● Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater. LIC0690 The front seats are warmed by built-in heaters (if so equipped).
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH REAR SONAR SYSTEM OFF SWITCH Push the switch again to turn the heated steering wheel off manually. The indicator light will go off. NOTE: The heated steering wheel switch is equipped with a 30 minute timer. After the switch has been activate for 30 minutes, the system will automatically turn off.If the surface temperature of the steering wheel is above 68°F (20°C) when the switch is turned on, the system will not heat the steering wheel. This is not a malfunction.
FRONT SONAR SYSTEM OFF SWITCH (If so equipped) the indicator light on the switch will illuminate. Push the switch again to enable the system. The indicator light will go off. The system will automatically reset the next time the ignition switch is turned on. See “Front sonar system” in the “Starting and driving” section. The system will automatically reset the next time the ignition switch is turned on. See “Rear sonar system” in the “Starting and driving” section.
TOW MODE SWITCH POWER OUTLET LIC1193 LIC0594 Tow mode should be used when pulling a heavy trailer or hauling a heavy load. Using tow mode at other times may cause unnecessary transmission shifting and reduced fuel economy. Press the tow mode switch to activate tow mode. The indicator light on the tow mode switch illuminates when tow mode is selected. Press the tow mode switch again to turn tow mode OFF. Tow mode is automatically canceled when the key is turned OFF.
CIGARETTE LIGHTER ● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open. ● When not in use, be sure to close the cap. Do not allow water to contact the outlet. LIC0551 Luggage area ● Use power outlets with the engine running to avoid discharging the vehicle battery. ● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on.
STORAGE CONSOLE BOX ● Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory. ● Use power outlets with the engine running to avoid discharging the vehicle battery. ● Avoid using power outlets when the air conditioner, headlights or rear window defroster is on. ● Before inserting or disconnecting a plug, be sure the electrical accessory being used is turned OFF. ● Push the plug in as far as it will go.
WIC1213 Console box storage trays WIC1214 LIC0591 Console box storage Console box lock 1 to open the console box lid Pull up on the lever s 2 . s 1 or unlock s 2 the Use the master key to lock s console box.
CAUTION ● Do not use for anything other than sunglasses. ● Do not leave sunglasses in the sunglasses holder while parking in direct sunlight. The heat may damage the sunglasses. LIC1176 WIC0673 GLOVE BOX SUNGLASSES HOLDER Open the glove box by pulling the handle. Use the 1 or unlocking s 2 the master key when locking s glove box. To open the sunglasses holder, push and release. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
LIC1195 MAP POCKETS LIC0568 LIC0575 Small bin SEATBACK POCKET The seatback pocket is located on the back of the driver seat. The pocket can be used to store maps.
CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. ● Use only soft cups in the cup holder. Hard objects can injure you in an accident. LIC0569 WIC1196 Medium bin Storage bins Front CUP HOLDERS WARNING Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. To open the front cup holders, push the cup holder lid. To close, lower the lid.
LIC0553 Adjustable Position the arm on the adjustable cup holder so that the cup is held securely. LIC0554 2nd row (rear of front console) To open the 2nd row cup holders (rear of the front console), lower the lid. To close, raise the lid.
LIC0556 2nd row bench (if so equipped) LIC0557 3rd row WIC1197 Bottle holder CAUTION ● Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. ● Do not use bottle holder for open liquid containers.
To reinstall the 2nd row center console box: 1. Slide the console box over the base toward the rear of the vehicle. 2. Push down to lock the console box in place. 3. Replace the cup holder tray. LIC0576 LIC0577 2ND ROW CENTER CONSOLE (if so equipped) Removing the 2nd row center console box Pull up on the lever to open the console box lid. To remove the 2nd row center console box: 1 s 2 s Lift out the cup holder tray. 3 s Move the console box toward the front of the vehicle and lift it out.
WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. ● Use suitable ropes and hooks to secure cargo. LIC0571 CARGO AREA STORAGE BIN To open the cargo area storage bin, pull down on the tab and pull the lid off.
LTI0089 LTI0090 Side finisher Floor hooks When hooking on ropes, do not apply a load of A hook or 44 more than 55 lb (245 N) to a single s B hook. lb (196 N) to a single s Do not apply a load of more than 110 lb (490 N) to a single hook.
WARNING ● Drive extra carefully when the vehicle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack. ● Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sudden or abnormal handling maneuvers. ● Roof rack load should be evenly distributed. ● Do not exceed maximum roof rack load weight capacity.
WINDOWS POWER WINDOWS Always distribute the luggage evenly on the roof rack. Do not load more than 200 lbs (91 kg) on entire roof rack. Be sure load is evenly distributed across both crossbars. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. label (located on the driver’s door pillar).
LIC1181 1. 2. 3. 4. 5. 6. Window lock button Power door lock switch Front passenger side automatic switch Right rear passenger window switch Left rear passenger window switch Driver side automatic switch Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close the front and rear passenger windows. To open a window, push the switch and hold it down. To close a window, pull the switch and hold it up.
Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window occurs. WARNING There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.
SUNROOF (if so equipped) The power vent windows operate when the ignition key is in the ON position, or for about 45 seconds after the ignition key is turned to the OFF position. If the driver’s or passenger’s door is opened during this 45 second period, power to the vent windows is cancelled. LIC0524 MANUAL VENT WINDOWS (if so equipped) To open a manual vent window, pull the latch handle toward you until it releases. To lock the window in the open position, push the latch handle rearward until it locks.
To open or close the sunroof part way, push the 5 while the roof is sliding switch in any direction s open or closed to stop it in the desired position. Tilting the sunroof To tilt the sunroof up, push the tilt switch toward 1 . When the sunroof is open, it the up position s will automatically close and then tilt up. To tilt the sunroof down, push the tilt switch 2 .
INTERIOR LIGHT are closed and the ignition switch is in the OFF position. ● The driver’s door is opened and then closed while the key is removed from the ignition switch. ● The key is removed from the ignition switch while all doors are closed. The lights will turn off while the 30 second timer is activated when: ● The driver’s door is locked by the keyfob, a key, or the power door lock switch. LIC0585 The interior light has a three-position switch and operates regardless of ignition switch position.
PERSONAL LIGHTS MAP LIGHTS LIC0587 LIC0588 LIC0586 1 will turn on whenever the The console light s parking lights or headlights are illuminated. The personal lights on the overhead console can be swiveled 360 degrees. To turn on the light, press the button. Press the button again to turn off the light. To turn the map lights on, press the switches. To turn them off, press the switches again. CONSOLE LIGHT The console light brightness can be adjusted with the illumination brightness control.
CARGO LIGHT HOMELINKT UNIVERSAL TRANSCEIVER The HomeLinkT Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLinkT Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems. LIC0590 The cargo light on the overhead trim has a threeposition switch.
4. Hold down both buttons until the indicator light on the HomeLinkT flashes, changing from a “slow blink” to a “rapidly flashing blink”. This could take up to 90 seconds. When the indicator light flashes rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, press and hold the programmed HomeLinkT button — releasing when the device begins to activate. WIC0986 PROGRAMMING HOMELINKT 1.
NOTE: Once you have pressed and released the program button on the garage door opener’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. Use the help of a second person for convenience to assist when performing this step. 7. Within 30 seconds of pressing and releasing the garage door opener program button, quickly and firmly press and release the HomeLinkT button you’ve just programmed. Press and release the HomeLinkT button up to 3 times to complete the training. 8.
CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared. However, to clear all programming, press and hold the two outside buttons and release when the indicator light begins to flash (approximately 20 seconds). REPROGRAMMING A SINGLE HOMELINKT BUTTON To reprogram a HomeLinkT Universal Transceiver button, complete the following. 1. Press and hold the desired HomeLinkT button. Do not release the button until step 4 has been completed. 2.
MEMO 2-64 Instruments and controls
3 Pre-driving checks and adjustments Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Intelligent keys (if so equipped) . . . . . . . . . . . . . . . . . . 3-2 NISSAN vehicle immobilizer system keys . . . . . . . . . . 3-3 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Locking with inside lock knob . . . . . . . . . . . . .
KEYS A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. WPD0128 1. 2. 3. 4. Two master keys (black) with transponder chip and chrome NISSAN brand symbol on one side Valet key (black) with transponder chip Key number plate Transponder chip A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle.
istration process requires erasing all memory in the Intelligent Key components when registering new keys, be sure to take all Intelligent Keys that you have to the NISSAN dealer. CAUTION Always carry the mechanical key installed in the Intelligent Key slot. Valet hand-off CAUTION When you have to leave a key with a valet, give them the Intelligent Key itself and keep the mechanical key with you to protect your belongings.
DOORS The master key can be used for all the locks. The valet key cannot be used for the console box lock. To protect belongings when you leave a key with someone, give them the valet key only. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can duplicate your existing key. As many as five NISSAN Vehicle Immobilizer System keys can be used with one vehicle.
Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with automatic operation at the same time. ● To open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. ● To close the windows, turn the driver’s door key to the front of the vehicle for longer than 1 second after the door is locked. Windows stop when the key cylinder is released.
REMOTE KEYLESS ENTRY SYSTEM Lockout protection It is possible to lock/unlock all doors, turn on the interior lights and puddle lamps (if so equipped), and activate the panic alarm by using the keyfob from outside the vehicle. When the power door lock switch (driver’s or front passenger’s side) is moved to the lock position with the key in the ignition and any door open, all doors will lock and then unlock automatically. This helps to prevent the keys from being accidently locked inside the vehicle.
button is pushed with all ● When the doors locked, the hazard warning lights flash twice and the horn beeps once as a reminder that the doors are already locked. The panic alarm will not activate when the key is in the ignition switch. CAUTION ● If a door is open and you push the button, the doors will lock but the horn will not beep and the hazard warning lights will not flash. Listed below are conditions or occurrences which will damage the keyfob: ● Do not allow the keyfob to become wet.
Push the 5 seconds. button on the keyfob again within ● All doors unlock. ● The hazard warning lights flash once if all doors are completely closed. The interior lights can be turned off without waiting 30 seconds by inserting the key into the ignition and turning to the ON or START position, locking the doors with the keyfob or pushing the interior light switch to the off position. Auto relock LPD0210 Unlocking doors Push the button on the keyfob once.
LPD0243 Operating the power lift gate (if so equipped) Push and hold the button on the keyfob for about 0.5 second to open or close the lift gate. The hazard warning lights flash and a chime sounds to indicate the power open or power close sequence has started. The lift gate will reverse direction immediately during power open or power close if the keyfob button is pressed. A chime will sound to announce the reversal. For more information, see “Lift gate” later in this section.
INTELLIGENT KEY SYSTEM (if so equipped) The hazard warning lights will flash three times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the and buttons for at least 2 seconds once more. The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not silence the horn if the alarm is triggered.
Since the Intelligent Key is continuously receiving radio waves, if the key is left near equipment which transmits strong radio waves, such as signals from a TV and personal computer, the battery life may become shorter. For information regarding replacement of a battery, see “Battery” in the “Maintenance and do-ityourself” section.
SPA2038 OPERATING RANGE The Intelligent Key functions can only be used when the Intelligent Key is within the specified 1 . operating range from the request switch s When the Intelligent Key battery is discharged or strong radio waves are present near the operating location, the Intelligent Key system’s operating range becomes narrower, and the Intelligent Key may not function properly. The operating range is within 31.50 in (80 cm) 1 .
● Do not pull the door handle before pushing the door handle request switch. The door will be unlocked but will not open. Release the door handle once and pull it again to open the door. WPD0411 INTELLIGENT KEY OPERATION You can lock or unlock the doors without taking the key out of your pocket or bag. When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch within the range of operation. WPD0412 Locking doors 1.
CAUTION ● After locking the doors using the request switch, make sure that the doors have been securely locked by operating the door handles or the rear liftgate opener switch. ● When locking the doors using the request switch, make sure to have the Intelligent Key in your possession before operating the request switch to prevent the Intelligent Key from being left in the vehicle. WPD0413 NOTE: ● Doors lock with the door handle request switch while the ignition switch is not in the LOCK position.
The interior light timer illuminates for 30 seconds when a door is unlocked and the room light switch is in the DOOR position. The interior light can be turned off without waiting for 30 seconds by performing one of the following operations. ● Placing the ignition switch in the ON position. ● Locking the doors with the remote controller. ● Switching the room light switch to the OFF position. WPD0412 Unlocking doors 1. Carry the Intelligent Key. 2. Push the door handle request switch. 3.
HOW TO USE THE REMOTE KEYLESS ENTRY FUNCTION CAUTION After locking the doors using the Intelligent Key, be sure that the doors have been securely locked by operating the door handles. The remote keyless entry function can operate all door locks using the remote keyless function of the Intelligent Key. The remote keyless function can operate at a distance of 33 ft (10 m) away from the vehicle. The operating distance depends upon the conditions around the vehicle.
The interior light illuminates for 30 seconds when a door is unlocked and the room light switch is in the DOOR position. The light can be turned off without waiting for 30 seconds by performing one of the following operations. ● Placing the ignition switch in the ON position. ● Locking the doors with the remote controller. ● Switching the room light switch to the OFF position. WPD0360 Unlocking doors 1. Push the button on the Intelligent Key. 2. The hazard warning lights flash once. 3.
The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not silence the horn if the alarm is triggered. WARNING SIGNALS To help prevent the vehicle from moving unexpectedly by erroneous operation of the Intelligent Key or to help prevent the vehicle from being stolen, a chime or buzzer sounds from inside and outside the vehicle and a warning is displayed in the instrument panel.
Symptom Possible Cause When pushing the ignition switch to stop the engine The SHIFT P warning appears on the display and the inside warning chime sounds continuously. The selector lever is not in the P (Park) position. When opening the driver’s door to get out of the vehicle The inside warning chime sounds continuously. The ignition switch is in the ACC position.
HOOD LIFT GATE WARNING ● Always be sure the lift gate has been closed securely to prevent it from opening while driving. ● Do not drive with the lift gate open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driving” section of this manual. LPD0244 s 1 2 s Pull the hood lock release handle located below the driver side instrument panel. The hood will spring up slightly.
LPD0247 LPD0245 OPERATING THE MANUAL LIFT GATE The power door lock system allows you to lock or unlock all doors including the lift gate simultaneously. To open the lift gate, pull up on the handle. To close, lower and push the lift gate down securely. Rear pillar switch OPERATING THE POWER LIFT GATE (if so equipped) NOTE: To open, close or reverse the power lift gate, the shift selector lever must be in P (Park). Also, the power lift gate will not operate if battery voltage is low.
● The keyfob button must be held for 0.5 second before the lift gate opens. ● The lift gate must be unlocked to open it with the outside opener handle. ● The switch on the rear pillar cannot be used to open the lift gate. A warning chime will sound if the shift selector lever is moved out of P (Park) during a power open operation. Power Close: The power lift gate automatically moves from the fully open position to the secondary position.
CAUTION ● If the power lift gate does not stay open or if the lift gate unexpectedly closes at any time while a continuous warning chime sounds, do not operate the lift gate. There may be a pressure loss in one or both of the lift gate gas stays. Have the lift gate inspected by a NISSAN dealer. ● Do not activate the power lift gate if one or both of the lift gate gas stays are removed. Damage to the lift gate or power lift gate mechanisms may occur.
● Do not drive with the lift gate open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driving” section of this manual. CAUTION ● If the power lift gate does not stay open or if the lift gate unexpectedly closes at any time while a continuous warning chime sounds, do not operate the lift gate. There may be a pressure loss in one or both of the lift gate gas stays. Have the lift gate inspected by a NISSAN dealer.
GLASS HATCH FUEL-FILLER DOOR NOTE: The lift gate must be unlocked in order to open the glass hatch. WARNING Do not drive with the glass hatch open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Exhaust gas” in the “Starting and driving” section of this manual. LPD0246 To open, pull up on the smaller outside handle to release the glass hatch, then pull up on the glass hatch. To close, lower and push the glass hatch down securely.
WARNING ● Gasoline is extremely flammable and highly explosive under certain conditions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling. ● Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.
STEERING WHEEL PEDAL POSITION ADJUSTMENT CAUTION Do not adjust the pedal position with your foot on the pedal. WPD0428 TILT OPERATION WARNING Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident. Pull the lock lever forward and hold it to adjust the steering wheel up or down to the desired position. Release the lock lever to lock the steering wheel in place. WPD0429 The accelerator and brake pedals can be adjusted for driving comfort.
SUN VISORS 1 s To block glare from the front, swing down the main sun visor. 2 s To block glare from the side, remove the main sun visor from the center mount and swing the visor to the side. 3 s To block glare from the side and front, swing down the sub-sun visor. 4 s Slide the extension sun visor in or out as needed. CAUTION ● Do not store the sun visor before returning the extension to its original position. ● Do not pull the extension sun visor forcedly downward.
MIRRORS NOTE: Do not hang any objects over the sensors 2 or apply glass cleaner to the sensors. s Doing so will reduce the sensitivity of the sensors, resulting in improper operation. WPD0331 AUTOMATIC ANTI-GLARE REARVIEW MIRROR The inside mirror is designed so that it automatically dims according to the intensity of the headlights of the vehicle following you. The automatic anti-glare feature operates only when the ignition switch is in the ON position.
WARNING ● Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use the inside mirror or glance over your shoulder to properly judge distances to other objects. ● Do not adjust the mirrors while driving. You could lose control of your vehicle and cause an accident. LPD0259 Manual folding outside mirrors (if so equipped) Push the mirrors backward to fold them.
AUTOMATIC DRIVE POSITIONER (if so equipped) Automatic anti-glare outside mirrors (if so equipped) The outside mirrors will automatically dim during nighttime conditions to reduce the glare from the headlights of trailing vehicles. The automatic antiglare feature operates only when the ignition switch is in the ON position. The automatic drive positioner system has two features: ● Memory storage function ● Entry/exit function The automatic anti-glare feature will be on when starting the vehicle.
3. Adjust the driver’s seat, accelerator and brake pedals, and outside mirrors to the desired positions by manually operating each adjusting switch. For additional information, see “Seats” in the “Safety—Seats, seat belts and supplemental restraint system” section and “Pedal position adjustment” and “Outside mirrors” earlier in this section. During this step, do not turn the ignition to any position other than ON. 4.
ENTRY/EXIT FUNCTION This system is designed so that the driver’s seat will automatically move when the automatic transmission selector lever is in the P (Park) position. This allows the driver to get into and out of the driver’s seat more easily. tems” section of this manual. For vehicles without navigation system, see your NISSAN dealer. Restarting the entry/exit function ● When the key is removed from the ignition switch and the driver’s door is opened.
4 Monitor, climate, audio, phone and voice recognition systems Control panel buttons — color screen without Navigation System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 How to use the NISSAN controller . . . . . . . . . . . . . . . 4-3 How to select menus on the screen . . . . . . . . . . . . . . 4-4 How to use the STATUS button . . . . . . . . . . . . . . . . . . 4-4 How to use the INFO button . . . . . . . . . . . . . . . . . . . . . 4-4 How to use the SETTING button . . . . . .
Rear audio controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-77 Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-77 NISSAN mobile entertainment system (MES) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-78 Digital video disc (DVD) player controls . . . . . . . . . . 4-79 Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-80 Flip-down screen . . . . . . . . . . . . . . . . . . . . . . .
CONTROL PANEL BUTTONS — COLOR SCREEN WITHOUT NAVIGATION SYSTEM WARNING ● Positioning of the heating or air conditioning controls and display controls should not be done while driving in order that full attention may be given to the driving operation. ● Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound.
● Finish setup. When you use this system, make sure the engine is running. 4 In some screens pressing the BACK button s accepts the changes made during setup. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. Reference symbols: ENTER button — This is a button on the control panel. “Display” key — This is a select key on the screen. By selecting this key you can proceed to the next function.
3. UP/DOWN Movement Indicator: Shows that the NISSAN controller may be used to move UP/DOWN on the screen and select more options. 4. Screen Count: Shows the number of menu selections available for that screen (for example, 5/6). 5. Footer/Information Line: Provides more information (if available) about the menu selection currently highlighted (for example, Enhances stereo imaging and sound). LHA0914 HOW TO SELECT MENUS ON THE SCREEN Vehicle functions are viewed on the center display screen in menus.
NOTE: ● If the amount of fuel added while the ignition switch is OFF is small, the display just before the ignition switch is turned OFF may continue to be displayed. ● When driving uphill or rounding curves, the fuel in the tank shifts, which may momentarily change the display.
Tire pressure rises and falls depending on the heat caused by the vehicle’s traveling condition and the temperature. In case of low tire pressure, a message is displayed on the screen: LOW PRESSURE — Check All Tires. WARNING LHA0923 Tire pressure information To display tire pressure information, press the INFO button, then select the “Tire Pressure” key using the NISSAN controller and press the ENTER button. Pressure indication in ** psi on the screen indicates that the pressure is being measured.
Resetting the drive computer Each item in the drive computer can be reset to 0. Select the “Reset” key on the item that needs to be reset using the NISSAN controller and press the ENTER button. To reset all of the items in the drive computer select the “Reset ALL” key and press the ENTER button. A confirmation screen will appear. Select the “Yes” key and press the ENTER button.
● The ignition key is turned ON the next time the vehicle will be driven. Resetting the maintenance interval To reset the reminder schedule (distance) to 0 miles (km), select the “Reset Distance” key using the NISSAN controller and press the ENTER button. To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button. The MAINTENANCE NOTICE screen displays each time the key is turned ON until one of the following conditions are met: ● The “Reset” key is selected.
LHA0927 Type A HOW TO USE THE SETTING BUTTON WHA0937 Type B LHA0929 Display settings Select the “Display” key and press the ENTER button. The Display settings screen will appear. When the SETTING button is pressed, the SETTINGS screen will appear on the display. You can select and/or adjust several functions, features and modes that are available for your vehicle. Use the NISSAN controller to select each item to be set and press the ENTER button.
To turn the screen on: ● Press the SETTING button and select the “Display” key and then select the “Display ON” key. Then set the screen to on by pressing the ENTER button, or ● Hold the OFF button for approximately 2 seconds and the message “resuming display” will appear and the “Display ON” key will be automatically turned on (no amber indicator).
Daylight Savings Time: When this item is enabled (indicator light illuminated), daylight savings time is on. To turn off the daylight savings time, touch the “ON” key; the amber indicator light will disappear. LHA0931 LHA0932 Beeps settings Clock Select the “Beeps” key and press the ENTER button. The Beeps settings screen will appear. The following display will appear after pressing the SETTING button, then selecting the “Clock” key using the NISSAN controller and pressing the ENTER button.
● Atlantic ● Newfoundland ● Aleutian ● Hawaii ● Alaska LHA0933 LHA0943 Time Zone: Clock Adjust: Select the “Time Zone” key; the Time Zone screen will appear. Adjust the time by manually inputting the correct time. Select one of the following zones, depending on the current location, by selecting the correct time zone key and pressing the ENTER button to enable that time zone (indicator light will illuminate for that location). ● 0 – 9: Select to change the number in the display.
● OK: Select to accept the changes made and return to the clock setting display. After selection/settings, press the BACK button or any other mode button to accept the changes. LHA0938 Comfort & Convenience settings (if so equipped) LHA0939 Indicator light is not illuminated — OFF Select the “Comfort & Conv.” key by using the NISSAN controller and pressing the ENTER button. The comfort and convenience option screen will be displayed.
Auto interior illumination: Select to turn on or turn off the illumination of the interior lights when any door is unlocked. Auto headlights sensitivity: Select to adjust the sensitivity of the automatic headlights higher (right) or lower (left). Auto headlights off delay: Select to change the duration of the automatic headlight off timer from 0, 30, 45, 60, 90, 120, 150 and 180 second periods.
Select to turn off all sounds made when a door handle request switch is pushed, by selecting the “OFF” key. Slide driver seat back on exit: Select to turn on or turn off the driver’s seat moving backwards for easy exit when the ignition switch is in the OFF position and the driver’s door is opened. After getting into the vehicle and pushing the ignition switch to the ACC position, the driver’s seat moves to the previous position.
OFF BUTTON To change the display brightness, press the OFF button. Pressing the button again will change the display to the day or the night display. Then, adjust the brightness by using the NISSAN controller. The display brightness can also be adjusted using the + (brighter) button or the 2 (dimmer) button. If no operation is done within 10 seconds, the display will return to the previous display.
CONTROL PANEL BUTTONS — COLOR SCREEN WITH NAVIGATION SYSTEM (if so equipped) 9. BACK (previous) button (P. 4-18) 10. ROUTE button* 11. ZOOM IN button* 12. MAP button* 13. ZOOM OUT button* *For Navigation system control buttons, refer to the separate Navigation System Owner’s Manual. **For information on the PHONE button, see “BluetoothT Hands-Free Phone System with Navigation System” later in this section. When you use this system, make sure the engine is running.
4 during setup, If you press the BACK button s the setup will be canceled and/or the display will return to the previous screen. ● Finish setup. 4 In some screens pressing the BACK button s accepts the changes made during setup. To help ensure safe driving, some functions cannot be operated while driving. 5 functions, refer to the For the VOICE button s separate Navigation System Owner’s Manual. The on-screen functions that are not available while driving will be “grayed out” or muted.
WHA0885 Touch screen operation With this system, the same operations as those for the NISSAN controller are possible using the touch screen operation. Selecting the item: Touch an item to select. To select the “Audio” key, 1 on the screen. Touch touch the “Audio” key s 2 to return to the previous the “BACK” key s screen. WHA0887 WHA0889 Adjusting the item: Inputting characters: 1 or the “2” key s 2 to adjust Touch the “+” key s 3 to scroll up to the settings.
● Symbols: Shows symbols such as the question mark (?). 2. Menu Selections: Shows the options to choose within that menu screen (for example, Auto Interior Illumination, etc.). ● Delete: Deletes the last character that has been input with one touch. Touch and hold the “Delete” key to delete all of the characters. 3. UP/DOWN Movement Indicator: Shows that the NISSAN controller may be used to move UP/DOWN on the screen and select more options. ● OK: Completes the character input. 4.
HOW TO USE THE STATUS BUTTON To display the status of the audio, climate control system, fuel consumption and navigation system, press the STATUS button.
NOTE: ● If the amount of fuel added while the ignition switch is OFF is small, the display just before the ignition switch is turned OFF may continue to be displayed. ● When driving uphill or rounding curves, the fuel in the tank shifts, which may momentarily change the display. Average fuel economy (MPG or L/100 km) The Average Fuel Economy is calculated based on fuel consumption since the last reset. The display is updated every 30 seconds and 1/3 mile (500 m).
Tire pressure rises and falls depending on the heat caused by the vehicle’s traveling condition and the temperature. Resetting the drive computer Each item in the drive computer can be reset to 0. Select the “Reset” key on the item that needs to be reset using the NISSAN controller and press the ENTER button. In case of low tire pressure, a message is displayed on the screen: LOW PRESSURE — Check All Tires.
Resetting the maintenance interval To reset the reminder schedule (distance) to 0 miles (km), select the “Reset Distance” key using the NISSAN controller and press the ENTER button. LHA0897 LHA0898 Maintenance items Changing the maintenance interval Press the INFO button and select the “Maintenance” key using the NISSAN controller and press the ENTER button; the maintenance information will be displayed on the screen.
● The ignition key is turned ON the next time the vehicle will be driven. To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button. The MAINTENANCE NOTICE screen displays each time the key is turned ON until one of the following conditions are met: ● The “Reset” key is selected. ● The “Interval Reminder ON” key is set to OFF (indicator light not illuminated).
Navigation version Refer to the separate Navigation System Owner’s Manual for information regarding this item. Traffic Info. Refer to the separate Navigation System Owner’s Manual for information regarding this item. Where am I? Refer to the separate Navigation System Owner’s Manual for information regarding this item. GPS Satellite Info. LHA0899 Voice recognition Refer to the separate Navigation System Owner’s Manual for information regarding this item.
LHA0901 LHA0902 WHA0823 Display settings Brightness/contrast: Display off: Select the “Display” key and press the ENTER button. The Display settings screen will appear. Select the “Brightness” key or the “Contrast” key to adjust the brightness or contrast of the map background. Use the NISSAN controller to adjust the brightness to darker or brighter and the contrast to lower or higher. Select the “Display ON” key.
To turn the screen on: Clock Format: ● Press the SETTING button and select the “Display” key and then select the “Display ON” key. Then set the screen to on by pressing the ENTER button, or Choose either the 12h (12 hour) clock display or the 24h (24 hour) clock display. Offset Adjust: Adjust the time by increasing or decreasing per minute.
● Atlantic ● Newfoundland ● Hawaii ● Alaska After selection/settings, press the BACK button or any other mode button to accept the changes. LHA0905 WHA0891 Time Zone: Comfort & Convenience settings Select the “Time Zone” key; the Time Zone screen will appear. Select the “Comfort & Conv.” key by using the NISSAN controller and pressing the ENTER button. The comfort and convenience option screen will be displayed.
Remote key response horn: Select to turn on or turn off the horn chirp mode used when the LOCK button on the keyfob is pressed. NOTE: If you change the horn beep or the lamp flash feature with the keyfob, the mode will not be changed with the display. Use the keyfob to return to the previous mode and re-enable the display control.
only the corresponding door is unlocked first. All the doors can be unlocked if the door unlock operation is performed again within 5 seconds. When this item is turned to off, all the doors will be unlocked after the door unlock operation is performed once. switch to the ACC position, the driver’s seat moves to the previous position. Reset all settings to default: Select to change all the comfort and convenience systems to their default settings.
Recognition system learn the user’s voice. The system can memorize the voices of up to three persons. For the details of this function, refer to “NISSAN Voice Recognition system” later in this section. ● User Guide Select this item to learn the operation flow of the NISSAN Voice Recognition system with the help of a step-by-step guide.
Volume and beeps settings Navigation volume For navigation volume settings refer to the separate Navigation System Owner’s Manual for information regarding these settings. Phone volume For phone volume settings refer to “BluetoothT Hands-Free Phone System With Navigation System” later in this section. LHA0912 LHA0913 Select Language: Select Units: Select the “English” key or the “Français” key to change the language shown on the display.
REARVIEW MONITOR (if so equipped) OFF BUTTON To change the display brightness, press the OFF button. Pressing the button again will change the display to the day or the night display. Then, adjust the brightness by using the NISSAN controller. If no operation is done within 10 seconds, the display will return to the previous display. Press and hold the OFF button for more than 2 seconds to turn the display off. Press the button again to turn the display on.
● When washing the vehicle with highpressure water, be sure not to spray it around the camera. Otherwise, water may enter the camera unit causing water condensation on the lens, a malfunction, fire or an electric shock. ● Do not strike the camera. It is a precision instrument. Otherwise, it may malfunction or cause damage resulting in a fire or an electric shock. CAUTION There is a plastic cover over the camera. Do not scratch the cover when cleaning dirt or snow from the cover.
OPERATING TIPS ● When the selector lever is shifted to R (Reverse), the monitor screen automatically changes to the rearview monitor mode. However, the radio can be heard. ● It may take some time until the rearview monitor is displayed after the selector lever has been shifted to R (Reverse). Objects may be distorted momentarily until the rearview monitor screen is displayed completely. When the selector lever is returned to a position other than R (Reverse), it may take some time until the screen changes.
VENTS LHA1030 Adjust air flow direction for the driver and pas1 , center s 2 , and rear passenger senger side s 3 and s 4 vents by moving the vent slide and/or s vent assemblies. 1 , open or close For driver and passenger side s vents by using the dial. Move the dial toward the to open the vents or toward the to close them.
HEATER AND AIR CONDITIONER (automatic) ● Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up. Start the engine and operate the controls to activate the air conditioner. AUTOMATIC OPERATION Cooling or heating (auto) LHA0859 1. Driver temperature control dial/AUTO button 2. A/C ON/OFF button 3. Fan speed control (increase) 4. Front window defroster button 5. MODE button 6. Passenger temperature control dial/ DUAL button 7.
● The temperature of the passenger compartment will be maintained automatically. Air flow distribution, fan speed and A/C on/off are also controlled automatically. ● A visible mist may be seen coming from the ventilators in hot, humid conditions as the air is cooled rapidly. This does not indicate a malfunction. Dehumidified defrosting or defogging 1. Push the defroster control button to turn the system on. The display will show the defrost icon. 2.
REAR SEAT AIR CONDITIONER LIC0836 LHA0863 1 , located on the top center The sunload sensor s of the instrument panel, helps the system maintain a constant temperature. Do not put anything on or around this sensor. Rear seat temperature and fan speed can be controlled from both the front seat overhead conA or the rear seat overhead console controls s B. sole controls s LHA0861 1. 2. 3. Rear fan speed control dial. Rear airflow mode buttons Rear temperature control dial.
SERVICING AIR CONDITIONER AUDIO SYSTEM The air conditioner system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. RADIO This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system.
Reception conditions will constantly change because of vehicle movement. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception. FM RADIO RECEPTION Range: FM range is normally limited to 25 – 30 miles (40 – 48 km), with monaural (single channel) FM having slightly more range than stereo FM.
Compact disc (CD) player CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD changer/player. ● Trying to load a CD with the CD door closed could damage the CD and/or CD changer. ● Only one CD can be loaded into the CD player at a time. ● Only use high quality 4.7 inches (12 cm) round discs that have the “COMPACT disc DIGITAL AUDIO” logo on the disc or packaging. ● During cold weather or rainy days, the player may malfunction due to the humidity.
CHECK DISC: ● Confirm that the CD is inserted correctly (the label side is facing up, etc.). ● Confirm that the CD is not bent or warped and it is free of scratches. PRESS EJECT: This is an error due to excessive temperature inside the player. Remove the CD by pressing the EJECT button. After a short time, reinsert the CD. The CD can be played when the temperature of the player returns to normal. UNPLAYABLE: The file is unplayable in this audio system (only MP3 CD).
● If there is a file in the top level of the disc, “Root Folder” is displayed. CompactFlash™ is a trademark of the SanDiskT Corporation in the United States of America and/or other countries. ● The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order. WHA0773 Playback order chart Playback order: Music playback order of a CD/CF with MP3 or WMA files is as illustrated.
Specification chart: Supported media CD, CD-R, CD-RW, CF ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. Supported file systems MP3 Supported versions*1 WMA*2 CompactFlash card: FAT12, FAT16, FAT32 Version MPEG1, MPEG2, MPEG2.5 Sampling frequency 8 kHz - 48 kHz Bit rate 8 kbps - 320 kbps, VBR*4 Version WMA7, WMA8, WMA9 Sampling frequency 32 kHz - 48 kHz Bit rate Tag information 32 kbps - 192 kbps, VBR ID3 tag VER1.0, VER1.1, VER2.
Troubleshooting guide: Symptom Cause and Countermeasure Check if the CD/CF was inserted correctly. Check if the CD/CF is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the player will play correctly after it returns to the normal temperature. Cannot play Files with extensions other than “.MP3”, “.mp3” or “.wma” cannot be played.
LHA0944 1. 2. 3. 4. 5. 6. RADIO AM·FM button* PRESET A·B·C button RPT button speaker control button RDM button PAUSE·MUTE button 7. 8. 9. 10. 11. 12. REAR CTRL button SCAN button TRACK button SEEK/CAT button TUNE/FLDR and AUDIO control knob CD load button 13. Station and CD select (1 - 6) buttons CD eject button 14. 15. VOL/ON·OFF control knob 16.
*When the RADIO AM·FM button is pressed, the satellite radio mode will be skipped unless an optional satellite receiver and antenna are installed and an XMT satellite radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam. Turn the VOL/ON·OFF control knob to adjust the volume.
While in this screen you can also adjust the other audio settings by selecting the corresponding key. Once you have adjusted the sound quality to the desired level, press the BACK button. For information on how to use the NISSAN controller, see “How to use the NISSAN controller” earlier in this section. Clock set For setting the clock, see “Clock” earlier in this section. WHA0941 For information on how to use the NISSAN controller, see “How to use the NISSAN controller” earlier in this section.
PAUSE·MUTE button: To mute or pause the audio sound, press the PAUSE·MUTE button. Press the PAUSE·MUTE button again to resume the audio sound. FM/AM/SAT radio operation FM/AM/SAT band select: Pressing the RADIO AM·FM button will change the band as follows: AM ←→ FM or SAT* (satellite, if so equipped) WHA0946 CD/MP3 display mode While listening to a CD or an MP3/WMA CD certain text might be able to be displayed (when CD encoded with text is being used).
The FM stereo indicator ST will illuminate during FM stereo reception. When the stereo broadcast signal is weak, the radio will automatically change from stereo to monaural reception. TUNE/FLDR (Tuning) knob: To manually tune the radio, turn the TUNE/FLDR knob to the right or left. SEEK/CAT and TRACK tuning buttons: Press the SEEK/CAT button or the TRACK button for less than 1.5 seconds to tune from high to low or low to high frequencies and stop at the next broadcasting station.
The slot numbers (1 – 6) will illuminate on the display when CDs are loaded into the changer. The NISSAN controller can also be used to select tracks when a CD is being played. DISC·AUX button: SEEK/CAT and TRACK (Rewind·Fast Forward) buttons: When the DISC·AUX button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.
MP3/WMA CD: ALL DISC MIX → 1 DISC MIX → 1 FOLDER MIX → ALL DISC MIX ALL DISC MIX: All discs loaded will be played in a mixed order. 1 DISC MIX: The tracks on the disc that is currently playing will be played in a mixed order. 1 FOLDER MIX: The tracks in the folder that is currently being accessed will be played in a mixed order. SCAN button: While listening to a CD, press the SCAN button to preview the first 10 seconds of each track on the CD playing.
WHA0948 AUX jack (if so equipped) 1 is located below the air condiThe AUX jack s tioner controls. The AUX audio input jack accepts any standard analog audio input, such as from a portable cassette tape player, MP3 player or laptop computers. Press the DISC·AUX button to play a compatible device when it is plugged into the AUX jack.
WHA0945 1. 2. 3. 4. 5. 6. PRESET A·B·C button DISC/AUX button speaker control button REAR CTRL button SCAN·RPT button TRACK button 7. 8. 9. 10. 11. 12. SEEK/CAT button TUNE/FLDR and AUDIO control knob CompactFlash insert slot Station select (1 - 6) buttons CD eject button VOL/ON·OFF control knob 13. AM·FM/SAT button* 14.
*When the AM·FM/SAT button is pressed, the satellite radio mode will be skipped unless an optional satellite receiver and antenna are installed and an XMT satellite radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam. Turn the VOL/ON·OFF control knob to adjust the volume.
While in this screen you can also adjust the other audio settings by touching the corresponding key. Once you have adjusted the sound quality to the desired level, touch the “BACK” key. Clock set For setting the clock, see “Clock” earlier in this section. LHA0900 WHA0942 Precision phased audio (if so equipped): To turn on or off the precision phased audio, press the SETTING button. Then touch the “Audio” key; the audio settings screen will be displayed. Touch the “Precision Phased Audio ON” key.
FM/AM/SAT radio operation FM/AM/SAT band select: Pressing the RADIO AM·FM button will change the band as follows: AM ←→ FM or SAT* (satellite, if so equipped) When the RADIO AM·FM button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. The last station played will also come on when the VOL/ON·OFF control knob is pressed ON.
TUNE/FLDR (Tuning) knob: To manually tune the radio, turn the TUNE/FLDR knob to the right or left. SEEK/CAT and TRACK tuning buttons: Press the SEEK/CAT button or the TRACK button for less than 1.5 seconds to tune from high to low or low to high frequencies and stop at the next broadcasting station. SCAN·RPT (SCAN tuning) button: Press the SCAN·RPT button to initiate scan tuning. Scan tuning will stop at each broadcasting station for 5 seconds.
SEEK/CAT and TRACK buttons: When the SEEK/CAT button is pressed while a compact disc is playing, the track being played returns to its beginning. Press several times to skip back through tracks. The compact disc will go back the number of times the button is pressed. When the TRACK button is pressed while the compact disc is playing, the next track will start to play from its beginning. Press several times to skip through tracks. The compact disc will advance the number of times the button is pressed.
When button is pressed while the compact disc is being played, the compact disc will eject and the system will turn off. WHA0948 AUX jack (if so equipped) 1 is located below the air condiThe AUX jack s tioner controls. The AUX audio input jack accepts any standard analog audio input, such as from a portable cassette tape player, MP3 player or laptop computers. Press the DISC/AUX button to play a compatible device when it is plugged into the AUX jack.
DISC/AUX button: When the DISC/AUX button is pressed with the system off and the CF card inserted, the system will turn on. If another audio source is playing and a CF card is inserted, press the DISC/AUX button repeatedly until the center display changes to the CompactFlash™ mode. WHA0953 CF display mode While listening to CF certain text might be able to be displayed.
SEEK/CAT and TRACK buttons: SCAN·RPT button: Press the SEEK/CAT button or the TRACK button while the CF card is being played, the next track or the beginning of the current track on the CF will be played. Pressing the SCAN·RPT button while the CF card is playing, the play pattern can be changed as follows: Press and hold the SEEK/CAT (rewind) button or the TRACK (fast forward) button for more than approximately 1.5 seconds, the CF card will play while rewinding or fast forwarding.
● Compact Disc Digital Audio (CD-DA) specification in CD-Extras. ● First session of multisession disc. Extreme temperature conditions [below 24°F (220°C) and above 158°F (70°C)] could affect the performance of the hard disk. NOTE: If the hard disk needs to be replaced due to a malfunction, all stored music data will be erased. WHA0955 Recording songs 1. Operate the audio system to play a CD. For information on playing CDs, see “Compact Disc (CD) player operation” earlier in this section. 2.
● The number of albums reaches the maximum of 500. Stopping playback: The system stops playing when: ● The number of tracks reaches the maximum of 3,000. ● Another mode (radio, CD, CompactFlash™ or AUX) is selected. Automatic recording: ● The audio system is turned off. If the “Automatic Recording” function is turned to ON, recording starts when a CD is inserted. For more information, see “Music Box settings” later in this section. ● The ignition switch is turned to the OFF position.
SCAN·RPT button: Pressing the SCAN·RPT button while a track is playing, the play pattern can be changed as follows: ALL Playlist RPT → 1 Playlist RPT → 1 TRK RPT → ALL Playlist RDM → 1 Playlist RDM → ALL Playlist RPT ALL Playlist RPT: the entire playlist will be repeated. 1 Playlist RPT: the playlist currently being played will be repeated. 1 TRK RPT: the current track playing will be repeated. ALL Playlist RDM: all the tracks in the playlist will be played randomly.
● Search Song Details Set the conditions and touch the “Start Song Search” key to search for a desired song that is stored in the system. The conditions are as follows: ● Play by Category Plays music from one of the following categories: – My Favorites – Hit Songs – Music Tempo (All, Slow, Normal and Fast) – Kids’ Songs – Decade (All, ’70s, ’80s, ’90s, ’00s, ’10s and After) – Rarely Played ● Search Artists Displays a list of artists in alphabetical order.
● Music Box System Info. Displays the following information about the Music Box audio system: – Music Box Used / Free Space Information about Saved Album, Saved Track and Remaining Time is displayed. – Mood Categories Number of saved tracks and their categories Relaxing Music, Lively Music, Slow Music, Upbeat Music and Others are displayed. – Deleted Items Information about the deleted tracks is displayed.
● Edit Info. Edit the name of the track being played and its artist using the keypad displayed on the screen. For information, see “How to use the touch screen” earlier in this section. The category of the track can also be set to Rock, Pop, Latin, Jazz, R&B, Hip Hop, Club/Dance, Punk, Reggae, Folk, Blues, Country, Metal, Easy Listening, New Age, Soundtrack, Gospel & Religious, World, Classical, Children’s and Others. ● Remove Track Reset the mood setting of a track.
LHA0965 Music Box settings To set up the Music Box hard-disk drive audio system to your preferred settings, touch the “Menu” key during playback, then touch the “Music Box System Info.” key, and then the “Music Box Settings” key. ● Automatic Recording: When this item is turned to ON, the Music Box hard-disk audio system automatically starts recording when a CD is inserted.
GracenoteT NOTE: ● The information contained in the GracenoteT Database is not fully guaranteed. ● The service of the GracenoteT Database on the Internet may be stopped without prior notice for maintenance. End-User License Agreement USE OF THIS PRODUCT IMPLIES ACCEPTANCE OF THE TERMS BELOW. GracenoteT MusicID™ Terms of Use This device contains software from Gracenote, Inc. of Emeryville, California (“Gracenote”).
● Do not use a conventional record cleaner or alcohol intended for industrial use. Copyright: Music recognition technology and related data are provided by GracenoteT. Gracenote is the industry standard in music recognition technology and related content delivery. For more information visit www.gracenote.com. CD and music-related data from Gracenote, Inc., copyright © 2000-2006 Gracenote. Gracenote Software, copyright © 2000-2006 Gracenote.
● Do not store the cards in highly humid locations. ● Do not expose the cards to direct sunlight. ● Do not spill any liquids on the cards. Refer to the CompactFlash™ card Owner’s Manual for more details. WHA0611 LHA1002 Type A CF cards: 1. 2. 3. 4. CAUTION Do not force the CompactFlash™ card into the CompactFlash™ player slot. Forcing the CF card could damage the pins inside the CF player slot, especially if the CF card is upside down or backwards.
If you have the Type B switch, with the ignition key turned to the ACC or ON position push the MODE switch to turn the audio system on. MODE select switch Push the mode select switch to change the mode in the following sequence: PRESET A → PRESET B → PRESET C → Music Box** (if so equipped) → CD* → CompactFlash™* (if so equipped) → DVD* (if so equipped) → AUX***. *These modes are only available when compatible media storage is inserted into the device. WHA0612 Type B 1. 2. 3. 4.
Change disc (CD) (if so equipped): Push the tuning switch or for more than 1.5 seconds to change the playing disc up or down. LHA0322 1. 2. 3. 4. 5. 6. VOL (volume) control button MODE select button speaker control button NEXT button SEEK button Headphone jacks 7. Infrared headphone transmitter lens* *Red transmitters will be visible when infrared headphones are on.
REAR AUDIO CONTROLS Press the REAR CTRL button on the front radio control panel to turn the rear controls on. Press the button again to turn rear controls off. Press the button; the headphones symbol illuminates on the front display when the headphones are on. Two headphone jacks are provided so two rear seat passengers may listen to the audio system privately. One or two infrared headphones are included if the vehicle is equipped with the DVD entertainment system.
NISSAN MOBILE ENTERTAINMENT SYSTEM (MES) (if so equipped) ● Do not attempt to modify the system to display a movie on the front screen while the vehicle is being driven. Doing so may distract the driver and may cause a collision and serious personal injury or death. Movies will not be shown on the front display while the vehicle is in any drive position to reduce driver distraction. Audio is available when a movie is played.
3. Auxiliary input jack: For information, see “DVD auxiliary input jacks” later in this section. WHA0967 1. 2. 3. EJECT button DVD slot Auxiliary input jack DIGITAL VIDEO DISC (DVD) PLAYER CONTROLS 1. EJECT button: When the button is pressed with the DVD loaded, it will be ejected. The display will show the eject symbol in the upper left corner of the display for 4 seconds once the button is pressed. If the DVD is not loaded, the display will show “NO DISC”.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. DISPLAY button MODE button SUBTITLE button AUDIO button ANGLE button CLEAR button PAUSE button PLAY button FAST FORWARD/FAST REVERSE button MENU button NAVIGATION keys BACK button NUMERIC KEYPAD REMOTE CONTROL Refer to “Remote controller operation” later in this section for the function of each button. LHA0315 FLIP-DOWN SCREEN The flip-down screen has a wireless remote con1 located at the bottom of the trol receiver s screen.
● The screen rotates down to view and up into the housing to store when not in use. Ensure that the screen is latched securely into the housing when stored. SAA0720 SAA0721 Headphones NOTE: Power ON/OFF: For optimum infrared headphone performance, increase the volume on the rear seat controller to the maximum level and adjust the infrared headphone volume using the volume control on the headphones.
BEFORE OPERATING THE DVD MOBILE ENTERTAINMENT SYSTEM Precautions Start the engine when using the DVD entertainment system. WARNING The driver must not attempt to operate the DVD System or wear the headphones while the vehicle is in motion so that full attention may be given to vehicle operation. CAUTION ● Only operate the DVD while the vehicle engine is running. Operating the DVD for extended periods of time with the engine OFF can discharge the vehicle battery. ● Do not allow the system to get wet.
Rear display: To adjust the rear display mode, press the DISP (Display) button on the remote controller. To adjust the display brightness, tint, color and contrast, select each key using the joystick on the remote controller and tilt the joystick to right or left.
Pressing the button on the front controls turns the rear speakers on or off and enables or disables the wireless headphones . It is possible to operate the DVD player by remote control. Headphones are a wireless type and no cables are necessary. You can use them in almost all the ranges in the rear seat. (It is not possible to use the headphones in the front seat.) DISC/AUX button Park the vehicle in a safe location for the front seat occupants to operate the DVD drive while watching the images.
SKIP (rewind) key: Touch the “ ” SKIP key to skip the chapter(s) of the disc backward. The chapters will go back the number of times the “ ” SKIP key is touched. Touch and hold the “ ” SKIP key for more than 1.5 seconds to rewind the disc. When the “ ” SKIP key is released the disc will be played normally. To skip the chapter(s) backward, it is also possible to press the button on the keypad of the remote controller.
Switch to DVD-AUX: Angle: Switch the output source from the DVD drive to another device connected to the auxiliary input jacks located on the DVD player. If the DVD contains different angles (such as moving images), the current image angle can be switched to another one. For more information, see “DVD auxiliary input jacks” later in this section. Choose a different angle by touching the “–” key or the “+” key; the angle will change if available.
Skip” key is turned on. Note that some discs may not be played directly even if this item is turned on. DVD Language: Touch the “DVD Language” key to open the number entry screen. Input the number corresponding to the preferred language and touch the “OK” key. The DVD top menu language will be changed to the one specified. DRC: DRC (Dynamic Range Compression) allows you to tune the dynamic range of the sound recorded in the DolbyT Digital format. Touch the “–” key or the “+” key to tune the DRC.
The DVD system can also be controlled by using the remote controller in the rear seats. See the following items. The display will show the “AUX” in the upper left corner of the display for 4 seconds once the Mode is changed to AUX. PWR on/off button: To use the input jacks, refer to “Auxiliary input jacks” in this section. With the ignition switch turned to the ACC or ON position, press the PWR button to turn the DVD rear display on or off.
NEXT CHAPTER/ PREVIOUS CHAPTER: When the (NEXT CHAPTER) button is pressed while the DVD is being played, the program next to the present one will start to play from its beginning. Press several times to skip through programs. The DVD will advance the number of times the button is pressed. When the (PREVIOUS CHAPTER) button is pressed, the program being played returns to its beginning. Press several times to skip back through programs. The DVD will go back the number of times the button is pressed.
AUDIO: Press the AUDIO button to call up audio menu. Repeatedly press the AUDIO button to cycle through each available audio track. ANGLE: Press the ANGLE button to call up camera angle menu. Repeatedly press the ANGLE button to cycle through each available angle. CLEAR: Press the CLEAR button to clear all numeric inputs, if actuated prior to expiration of the 3-second timer.
● A new disc may be rough on its inner and outer edges. Remove the rough edges using the side of a pen or pencil as illustrated. ● Never attempt to use a DVD that has been cracked, deformed, or repaired using adhesive. Doing so may cause damage to the equipment. ● Handle the DVD carefully to avoid contamination or flaws. Otherwise, signals may not be read properly. LHA0049 HOW TO HANDLE THE DVD CAUTION ● Handle a DVD by its edges. Never touch the surface of the disc.
● DVDs with a region code other than A is displayed in “1”. The region code s a small symbol printed on the top of B the DVD s 5. If the disc cannot be ejected see your NISSAN dealer for further assistance. 6. Re-program the radio presets.
CAR PHONE OR CB RADIO ● When changing batteries, do not let dust or oil get on the remote control and headphones. FCC Notice: SAA0723 If the battery is removed for any reason other than replacement, close the lid securely. ● If you will not be using the remote control for long periods of time, remove the batteries. ● Replacement of the batteries is needed when the remote control only functions at extremely close distances to the DVD player or not at all.
BLUETOOTHT HANDS-FREE PHONE SYSTEM WITHOUT NAVIGATION SYSTEM (if so equipped) CAUTION ● Keep the antenna as far away as possible from the electronic control modules. ● Keep the antenna wire more than 8 in (20 cm) away from the electronic control system harnesses. Do not route the antenna wire next to any harness. ● Adjust the antenna standing-wave ratio as recommended by the manufacturer. ● Connect the ground wire from the CB radio chassis to the body. ● For details, consult a NISSAN dealer.
module when the ignition switch is placed in the ON position with the paired cellular phone turned on and carried in the vehicle. You can register up to 5 different BluetoothT cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. Before using the BluetoothT Hands-Free Phone System, refer to the following notes. ● Set up the wireless connection between a cellular phone and the in-vehicle phone module before using the hands-free phone system.
– Your cellular phone is locked to prevent it from being dialed. ● When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person’s voice during a call. ● Do not place the cellular phone in an area surrounded by metal or far away from the in-vehicle phone module to prevent tone quality degradation and wireless connection disruption.
● If a command is not recognized, the system announces, “Command not recognized. Please try again.” Repeat the command in a clear voice. ● If you want to go back to the previous command, you can say “Go back” or “Correction” any time the system is waiting for a response. ● You can cancel a command when the system is waiting for a response by saying, “Cancel” or “Quit.” The system announces “Cancel” and ends the VR session. You can also press the button on the steering wheel at any time.
PHONE/END button to cancel a VR Press the session or end a call. GETTING STARTED The following procedures will help you get started using the BluetoothT Hands-Free Phone System with NISSAN Voice Recognition. For additional command options, refer to “List of voice commands” later in this section. Choosing a language WHA0976 CONTROL BUTTONS The control buttons for the BluetoothT HandsFree Phone System are located on the steering wheel.
5. If you decide not to change the language, do not press either button. After 5 seconds, the VR session will end, and the language will not be changed. Pairing procedure NOTE: The pairing procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Main Menu A “Setup” s B “Pair phone” s C “New phone” s D Initiate from handset s E Name phone s F Assign priority s G Choose ringtone s 1.
B . For 3. Say the number you wish to call s example, 555-1212 can be said as “five five five one two one two.” See “How to say numbers” earlier in this section for more information. 4. When you have finished speaking the phone number, the system repeats it back and announces the available commands. C . The system acknowledges 5. Say: “Dial” s the command and makes the call.
When prompted by the system, say the name of the phone book entry you wish to call. The system acknowledges the name. If there are multiple locations associated with the name, the system asks you to choose the location. Once you have confirmed the name and location, the system begins the call. B Number (speak digits) s When prompted by the system, say the number you wish to call. Refer to “How to say numbers” and “Making a call by entering a phone number” earlier in this section for more details.
“Phone book” NOTE: When prompted by the system, say the name you would like to give the new entry. For example, say: “Mary.” Phone book commands are not available when the vehicle is moving. Main Menu “Phone Book” A “New Entry” s B “Edit” s C “Delete” s D 9List Names” s If the name is too long or too short, the system tells you, then prompts you for a name again. Also, if the name sounds too much like a name already stored, the system tells you, then prompts you for a name again.
The system acknowledges the location. C “Delete” s The system will ask you to say a phone number or to transfer a phone number stored in the cellular phone’s memory. Use the Delete command to erase one entry from the phone book, all entries from the phone book, the current redial number or the current call back number. Enter a phone number by voice command: For example, say: “five five five one two one two. ” See “How to say numbers” earlier in this section for more information.
B “Play” s The system plays back all the memos in the order of newest to oldest. The system ends the VR session. If there are no memos recorded, the system announces “No messages to play.” The system ends the VR session. C “Delete” s The Delete command erases all memos. The system asks you to confirm this action before deleting all memos. “Setup” Main Menu “Setup” A “Pair Phone” s B “List Phone” s Use the Setup command to change options associated with the BluetoothT Hands-Free Phone System.
D “Change priority” s Use the Change Priority command to change the priority level of the active phone. The priority level determines which phone is active when more than one paired BluetoothT phone is in the vehicle. The system states the priority level of the active phone and asks for a new priority level (1, 2, 3, 4, 5). If the new priority level is already being used for another phone, the two phones will swap priority levels.
Training procedure The procedure for training a voice is as follows. 8. The SA mode will be explained. Follow the instructions provided by the system. 1. Position the vehicle in a reasonably quiet outdoor location. 9. When training is finished, the system will tell you an adequate number of phrases have been recorded. 2. Sit in the driver’s seat with the engine running, the parking brake on, and the transmission in P (Park). 10. The system will ask you to say your name.
● dial eight three zero five one ● setup main menu TROUBLESHOOTING GUIDE ● Home ● Delete ● four three pause two nine pause zero ● dial nine seven two six six ● delete redial number ● memo pad delete The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions.
BLUETOOTHT HANDS-FREE PHONE SYSTEM WITH NAVIGATION SYSTEM (if so equipped) WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. ● If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle before doing so.
module when the ignition switch is turned to the ON position with the paired cellular phone turned on and carried in the vehicle. You can register up to 5 different BluetoothT cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. NISSAN Voice Recognition system supports the phone commands, so dialing a phone number using your voice is possible. For more details, see “NISSAN Voice Recognition System” later in this section.
VOICE COMMANDS You can use voice commands to operate various BluetoothT Hands-Free Phone System features using the NISSAN Voice Recognition system. For more details, see 9NISSAN Voice Recognition System9 later in this section. LHA0884 PAIRING PROCEDURE LHA0978 NOTE: 1. Press the SETTING button, then select the “Phone” key using the NISSAN controller and press the ENTER button. If pairing a phone for the first time, pressing the PHONE button twice will bring you to the pair phone list. 2.
LHA0979 LHA0980 LHA0981 Monitor, climate, audio, phone and voice recognition systems 4-111 Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X
LHA0982 LHA0978 LHA0983 Up to 40 phone numbers can be stored in the phonebook. 4. Select the “Transfer via Bluetooth” key in order to transfer a phonebook entry from your cellular phone to your phonebook in your car. PHONEBOOK 1. Press the SETTING button, then select the “Phone” key and press the ENTER button. 2. Select the “Phonebook” key and press the ENTER button. 3. Select one of the “None (Add New)” keys from the name list of the phonebook and press the ENTER button. 5.
Copy from Downloaded Phonebook: Copy a phonebook from the BluetoothT cellular phone. The availability of this function depends on each cellular phone. The copying procedure from the cellular phone also varies according to each cellular phone. See the cellular phone owner’s manual for more details. Copy from Outgoing Call Logs: Store the name and phone number from the outgoing call list. Copy from Incoming Call Logs: Store the name and phone number from the incoming call list. LHA0984 LHA0985 6.
c. Press the PHONE button on the instrument panel. There are different methods to make a call. Select one of the following options instead of the “Call (Phonebook)” key in step 2 above. Redial: Dial the previously dialed number again. Call (Call Logs): Select the name or phone number from the incoming or outgoing call logs. LHA0986 MAKING A CALL To make a call, follow the procedures below. 1. Press the PHONE button on the instrument panel.
Answer: Accept an incoming call to talk. Keypad: Brings up a keypad; enter digits when needed. For example, entering your PIN number for voicemail. On Hold: Put an incoming call on hold. Cancel Mute: This will appear after the “Mute” key is touched. Mute will be cancelled. Reject Call: Reject an incoming call. To finish the call, follow one of the procedures listed below.
● Delete an Entry of Downloaded Phonebook: Delete a single entry from the downloaded phonebook. Touch the corresponding letter key, then touch on the name key you wish to delete. Touch the “Yes” key to delete the entry. Automatic Hold: If this item is turned on, an incoming call will be placed on hold automatically after several rings. LHA0978 PHONE SETTING To set up the hands-free phone system to your preferred settings, press the SETTING button, then touch the “Phone” key on the display.
NISSAN VOICE RECOGNITION SYSTEM (if so equipped) The NISSAN Voice Recognition system allows hands-free operation of the systems equipped on this vehicle, such as the display, audio, climate control, DVD, phone and navigation systems. To operate NISSAN Voice Recognition, press button located on the steering wheel. the Then speak the command for the system you wish to activate. The command given is picked up by the microphone, and it is performed when it is properly recognized.
LHA0892 LHA0908 1. Press the INFO button on the instrument panel. 7. Press the BACK button to return to the previous screen. 2. Touch the “Others” key, then touch the “Voice Recognition” key. For information on how to use the touch screen, see “How to use the touch screen” earlier in this section. 3. Touch the “Command List” key. 4. Touch one of the category keys. 5. Touch one of the item keys in the category; a command list will be shown. 6.
LHA0990 LHA0991 LHA0992 Monitor, climate, audio, phone and voice recognition systems 4-119 Z REVIEW COPY—2008 Armada (wzw) Owners Manual—USA_English (nna) 03/05/07—arosenma X
List of help commands Navigation help: See the separate Navigation System Owner’s Manual for details. Audio help: ● Music Box COMMAND Music Box Play ACTION Turns on the Music Box hard-disk drive audio system. Play by Mood Plays the specified song matching your mood. Relaxing Music Plays the specified relaxing music. Lively Music Plays the specified lively music. Slow Music Plays the specified slow music. Upbeat Music Plays the specified upbeat music.
● Radio – Radio COMMAND ACTION Radio Play Turns the radio on, selecting the station and band last played. Radio AM Turns to the AM band, selecting the station last played. Radio FM Turns to the FM band, selecting the station last played. Tune <87.7 - 107.9> Tunes to the specified FM frequency. Tune <530 - 1710> Tunes to the specified AM frequency. Preset <1 - 6> Switches directly to the specified preset station in the specified preset bank.
● DVD (if so equipped) NOTE: DVD commands are available while a DVD is being played. COMMAND DVD Play ACTION Turns the DVD player on, selecting the track last played. DVD Stop Stops playing the DVD. Track <1 to 99> Switches to the specified DVD track. Chapter <1 to 999> Switches to the specified DVD chapter. Title <1 to 99> Switches to the specified DVD title. Title <1 to 99> Chapter <1 to 999> Switches to the specified DVD title on the specified chapter.
● CD COMMAND ACTION CD Play Starts to play a CD. Track <1 - 512> Switches to the specified track. Folder <1 - 255> Selects the specified MP3 folder and plays the first file. Folder <1 - 255> Track <1 - 512> Switches to the specified track on the specified MP3 folder. CD OFF Stops the CD playback. CD Text Displays the information about the track currently being played. CD Menu Displays the CD menu. ● Others – Audio COMMAND ACTION Audio Play Turns the audio system on.
– CF COMMAND ACTION Compact Flash Play Starts to play the files saved in the CompactFlash™ card. Track <1 - 512> Switches to the specified track. Folder <1 - 255> Selects the specified folder in the CompactFlash™ card and plays the first file. Folder <1 - 255> Track <1 - 512> Switches to the specified track in the specified folder in the CompactFlash™ card. Compact Flash OFF Stops the playback of the CompactFlash™ card.
Climate control help: COMMAND ACTION Climate Control Turns the climate control system on and operates it in the AUTO mode. Climate Control OFF Turns the climate control system off. Temperature <60 - 90> or <18 - 32°C> Sets the climate control temperature to the value given in the command. Driver Temperature <60 - 90> or <18 - 32°C> Sets the driver’s side temperature to the value given in the command.
● Voice Recognition Settings Displays the description of voice recognition settings. ● Adapting the System to Your Voice Simulates an example of the operation to adapt the system to your voice. For the items “Using the Address Book” and “Finding a Street Address”, refer to the separate Navigation System Owner’s Manual for details. For information on how to use the touch screen, see “How to use the touch screen” earlier in this section.
Operating tips To get the best performance out of NISSAN Voice Recognition, observe the following: ● Keep the interior of the vehicle as quiet as possible. Close the windows to eliminate the surrounding noises (traffic noises, vibration sounds, etc.), which may prevent the system from recognizing the voice commands correctly. ● When the climate control is in the AUTO mode, the fan speed decreases automatically for easy recognition. ● Wait until a tone sounds before speaking a command.
● If you want to cancel the command, press button for 2 seconds and hold the during feedback. The system will announce: “Voice cancelled.” ● If you want to adjust the volume of the voice feedback, push the volume control switch or the on the steering wheel while being provided with the feedback. Operating tips ● Voice commands cannot be accepted when the face icon in the display is gray. ● If the command is not recognized, the system announces, “Please say again”. Repeat the command in a clear voice.
Temperatures (climate control): Speak temperatures according to the following examples: ● 74°F – “Temperature seventy four” ● 21.5°C – “one eight zero zero six six two six two oh oh”. Note 1: For the best voice recognition phone dialing results, say phone numbers as single digits. Note 2: You cannot say 555-6000 as “five five five six thousand”.
LHA0909 LHA0910 Having the system learn the user’s voice 1. Press the SETTING button on the instrument panel, touch the “Others” key on the display. 2. Touch the “Voice Recognition” key. 3. Touch the “Voice Command Learning” key. LHA0997 4. Touch one of the User number keys to have your voice memorized by the system as that user. 5. Touch a category to be learned by the system from the following list: ● Audio ● Phone ● Vehicle Info. ● Others The voice commands in the category are displayed.
LHA0998 LHA1000 6. Touch a voice command. The voice recognition system starts. 7. The system requests that you repeat a command after a tone. LHA0999 8. After the tone sounds and the face icon on the screen changes from to gray to orange, speak the command that the system requested. 9. When the system has recognized the voice command, the voice of the user is learned. Press the BACK button to return to the previous screen.
● Reset Result: Resets the user’s voice that the voice recognition system has learned. ● Continuous Learning: When this item is turned to ON, you can have the system learn the voice commands in succession, without selecting commands one by one.
LHA0909 LHA0910 Voice Command Learning: For information, see “Voice command learning function” earlier in this section. User Guide: For information, see “Displaying the user guide” earlier in this section.
TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, follow the solutions given in this guide for the appropriate error. Where the solutions are listed by number. Try each solution in turn, starting with number one, until the problem is resolved. Symptom/error message Displays “COMMAND NOT RECOGNIZED” or the system fails to interpret the command correctly. Solution 1. Ensure that the command format is valid.
5 Starting and driving Precautions when starting and driving. . . . . . . . . . . . . . . . 5-2 Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . 5-2 Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 On-pavement and off-road driving precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 5-3 Avoiding collision and rollover . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS WHEN STARTING AND DRIVING WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunctions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating conditions are detected.
even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. km/h). Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving). Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. Some examples are: ● Replacing tires with those not originally specified by NISSAN could affect the proper operation of the TPMS.
significantly more likely to be injured or killed than a person properly wearing a seat belt. DRINKING ALCOHOL/DRUGS AND DRIVING WARNING Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury.
● To avoid raising the center of gravity excessively, do not exceed the rated capacity of the roof rack and evenly distribute the load. Secure heavy loads in the cargo area as far forward and as low as possible. Do not equip the vehicle with tires larger than specified in this manual. This could cause your vehicle to roll over. ● For 4WD equipped vehicles, do not attempt to raise two wheels off the ground and shift the transmission to any drive or reverse position with the engine running.
IGNITION SWITCH ● Whenever you drive off-road through sand, mud or water as deep as the wheel hub, more frequent maintenance may be required. See “Periodic maintenance” in the “NISSAN Service and Maintenance Guide.” WARNING ● Never remove or turn the key to the LOCK position while driving. The steering wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury. ● Never turn the ignition switch to the LOCK position while driving.
When the ignition switch cannot be turned toward the LOCK position while keeping the Intelligent Key, proceed as follows: 1. Move the selector lever into the P (Park) position. 2. Turn the ignition switch slightly in the ON direction. 3. Turn the key toward the LOCK position. The selector lever can be moved from the P (Park) position if the ignition switch is in the ON position and the foot brake pedal is depressed.
To remove the key from the ignition switch: 1. Shift the selector lever to the P (Park) position with the key in the ON position. 2. Turn the key to the LOCK position. 3. Remove the key from the ignition. If the selector lever is shifted to the P (Park) position after the key is turned to the OFF position or when the key cannot be turned to the LOCK position, proceed as follows to remove the key.
BEFORE STARTING THE ENGINE START: (4) This position starts the engine. As soon as the engine has started, release the key. It automatically returns to the ON position. NISSAN VEHICLE IMMOBILIZER SYSTEM ● Make sure the area around the vehicle is clear. ● Check fluid levels such as engine oil, coolant, brake fluid, and window washer fluid as frequently as possible, or at least whenever you refuel. ● Check that all windows and lights are clean.
DRIVING THE VEHICLE cranking the engine, release the accelerator pedal. Crank the engine with your foot off the accelerator pedal by turning the ignition key to START. Release the key when the engine starts. If the engine starts, but fails to run, repeat the above procedure. CAUTION Do not operate the starter for more than 15 seconds at a time. If the engine does not start, turn the key off and wait 10 seconds before cranking again, otherwise the starter could be damaged. 4.
WARNING Overheating can result in reduced engine power and vehicle speed. The reduced speed may be lower than other traffic, which could increase the chance of a collision. Be especially careful when driving. Pull to the side of the road to a safe area. Allow the engine to cool and return to normal operation. See “If your vehicle overheats” in the “In case of emergency” section of this manual.
WARNING Apply the parking brake if the selector lever is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage. WSD0187 To move the selector lever: : Shift while depressing the brake pedal : Shift without depressing brake pedal Shifting After starting the engine, fully depress the brake pedal and move the shift selector lever out of the P (Park) position.
4H: 1 (Low gear): 62 MPH (100 km/h) Use this position when climbing steep hills slowly or slow driving through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. 4LO: 31 MPH (50 km/h) 3 (Third gear): Use this position for driving up and down long slopes where engine braking would be advantageous. Do not downshift into the 1 position at speeds over the following and do not exceed the following speeds in the 1 position.
PARKING BRAKE To push the shift lock release, complete the following procedure: 1. Turn the ignition key to the LOCK position and remove the key 2. Apply the parking brake. 3. Remove the shift lock release cover as shown. 4. Insert a small screwdriver in the shift lock release slot and push down. 5. Move the shift selector lever to the N (Neutral) position while holding down the shift lock release. 6. Turn the key to the ON position to unlock the steering wheel.
CRUISE CONTROL ● If the SET indicator light blinks, push the cruise control ON·OFF switch off and have the system checked by a NISSAN dealer. ● The SET indicator light may blink when the cruise control ON·OFF switch is pushed ON while pushing the ACCEL/RES, COAST/SET, or CANCEL switch. To properly set the cruise control system, use the following procedures. WARNING Do not use the cruise control when driving under the following conditions: LSD0158 To engage: Firmly depress the parking brake. To release: 1.
CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed between 25 - 89 MPH (40 - 144 km/h) without keeping your foot on the accelerator pedal. To turn on the cruise control, push the ON·OFF switch on. The CRUISE indicator light in the vehicle information display will illuminate. To set cruising speed, accelerate the vehicle to the desired speed, push the COAST/SET switch and release it. The SET indicator light in the vehicle information display will illuminate.
BREAK-IN SCHEDULE CAUTION During the first 1,200 miles (2,000 km), follow these recommendations to obtain maximum engine performance and ensure the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in shortened engine life and reduced engine performance. ● Avoid driving for long periods at constant speed, either fast or slow, and do not run the engine over 4,000 rpm. ● Do not accelerate at full throttle in any gear. ● Avoid quick starts.
USING FOUR WHEEL DRIVE (4WD) WARNING ● For 4WD equipped vehicles, do not attempt to raise two wheels off the ground and shift the transmission to any drive or reverse position with the engine running. Doing so may result in drivetrain damage or unexpected vehicle movement which could result in serious vehicle damage or personal injury.
4WD Shift Switch Position AUTO Wheels Driven 4WD shift Indicator Light Transfer 4LO position Rear wheels or 4 wheels For driving on paved or slippery roads Rear wheels For driving on dry, paved roads (Economy drive) or state dynamometer I/M testing 4 wheels For driving on rocky, sandy or snowcovered roads 2WD 4H Neutral *1 May blink 4LO Use Conditions 4 wheels Illuminated Neutral disengages the automatic transmission mechanical parking lock, which will allow the vehicle to roll.
The transfer case 4WD shift switch is used to select either 2WD or 4WD depending on the driving conditions. There are four types of drive modes available, AUTO, 2WD, 4H and 4LO. The 4WD shift switch electronically controls the transfer case operation. Rotate the switch to move between each mode, 2WD, AUTO, 4H and 4LO. You must push the switch in to select 4LO, and the vehicle MUST be stationary and the automatic transmission selector lever in the N position when changing into or out of 4LO.
● If the vehicle is stuck deep in mud, place stones or wooden blocks under the tires. Then try the recovery procedures above. Tire chains may be effective. 4LO, you may feel a jolt. This is not abnormal. ● When the vehicle is stopped after making a turn, you may feel a slight jolt after the selector lever is shifted to N or P. This occurs because the transfer clutch is released and not because of a malfunction. CAUTION ● Do not spin the tires excessively.
drive the vehicle straight, accelerate or decelerate or move the vehicle in reverse, then shift the 4WD shift switch. ● Engine idling speed is high while warming up the engine. Be especially careful when starting or driving on slippery surfaces with the 4WD shift switch set in AUTO. ● If the 4WD warning light comes on, the 4WD indicator light goes out. 4WD shift indicator light CAUTION LSD0147 The 4WD shift indicator light is located in the vehicle information display.
4WD warning light Warning light Comes on Blinks rapidly Blinks slowly Comes on or blinks when: There is a malfunction in the 4–wheel drive system The transfer case oil temperature is abnormally high The difference in wheel rotation is large The 4WD warning light is located in the meter. The 4WD warning light comes on when the key switch is turned to ON. It turns off soon after the engine is started.
PARKING/PARKING ON HILLS A ● HEADED DOWNHILL WITH CURB: s Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb. B ● HEADED UPHILL WITH CURB: s Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb. ● HEADED UPHILL OR DOWNHILL, NO C CURB: s WSD0050 WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.
POWER STEERING BRAKE SYSTEM The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at two wheels. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.
This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKING SYSTEM (ABS) WARNING ● The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces. Remember that stopping distances on slippery surfaces will be longer than on normal surfaces even with ABS.
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM pedal. This is normal and does not indicate a malfunction. If the computer senses a malfunction, it switches the ABS off and illuminates the ABS warning light on the instrument panel. The brake system then operates normally, but without anti-lock assistance. If the ABS warning light illuminates during the self-test or while driving, have the vehicle checked by a NISSAN dealer. When accelerating or driving on slippery surfaces, the tires may spin or slide.
REAR SONAR SYSTEM (if so equipped) WARNING ● The vehicle dynamic control system is designed to help improve driving stability but does not prevent accidents due to abrupt steering operation at high speeds or by careless or dangerous driving techniques. Reduce vehicle speed and be especially careful when driving and cornering on slippery surfaces and always drive carefully.
FRONT SONAR SYSTEM (if so equipped) ● The system is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground. ● If your vehicle sustains damage to the rear bumper fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms.
COLD WEATHER DRIVING ● The system is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground. ● If your vehicle sustains damage to the front bumper fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms.
DRAINING OF COOLANT WATER If the vehicle is to be left outside without antifreeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see “Changing engine coolant” in the “Maintenance and do-it-yourself” section of this manual. TIRE EQUIPMENT 1. SUMMER tires have a tread designed to provide superior performance on dry pavement. However, the performance of these tires will be substantially reduced in snowy and icy conditions.
ENGINE BLOCK HEATER (if so equipped) WARNING ● Do not use your engine block heater with an ungrounded electrical system or a 2-pronged adapter. You can be seriously injured by an electrical shock if you use an ungrounded connection. ● Disconnect and properly store the engine block heater cord before starting the engine. Damage to the cord could result in an electrical shock and can cause serious injury. ● Use a heavy-duty 3-wire, 3-pronged extension cord rated for at least 10 A.
6 In case of emergency Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 6-2 Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 Push starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 If your vehicle overheats . . . . . . . . . . . . . . . .
FLAT TIRE TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. If equipped, the system also displays pressure of all tires (except the spare tire) on the display screen by sending a signal from a sensor that is installed in each wheel.
WARNING ● Make sure the parking brake is securely applied and the automatic transmission is shifted into P (Park). ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. ● Never change tires if oncoming traffic is close to your vehicle. Wait for professional road assistance. WCE0044 LCE0086 3. Unscrew and remove the jack.
CAUTION Be sure to center the spare tire suspending plate on the wheel and then lift the spare tire. Jacking up vehicle and removing the damaged tire WARNING LCE0084 LCE0085 4. Assemble the two pieces of the jack rod. Find the oval-shaped opening above the middle of the license plate. Pass the T-shaped end of the jack rod through the opening and direct it toward the spare tire winch, located directly above the spare tire. 5.
● Do not start or vehicle is on the vehicle to move. for vehicles differentials. run the engine while jack. It may cause the This is especially true with limited slip ● Do not allow passengers to stay in the vehicle while it is on the jack. ● Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move. NOTE: Before jacking up the vehicle, make sure the ignition key is in the OFF position.
2. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the vehicle at the jack-up point. The jack-up points are indicated by stamped arrows on the side of the frame. WCE0139 LCE0087 The jack should be used on firm and level ground. 3. Install the assembled jack rod into the jack as shown. 4. To lift the vehicle, securely hold the jack lever and rod. Carefully raise the vehicle until the tire clears the ground.
5. Remove the wheel nuts and then remove the tire. 4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated. Lower the vehicle completely. WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident. WCE0063 Installing the spare tire The spare tire is designed for emergency use.
JUMP STARTING Adjust tire pressure to the COLD pressure. COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mile (1.6 km). COLD tire pressures are shown on the Tire and Loading Information label affixed to the driver side center pillar. After adjusting tire pressure to the COLD tire pressure, the display of the tire pressure information may show higher pressure than the COLD tire pressure after the vehicle has been driven more than 1 mile (1.6 km).
● Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting. ● Do not attempt to jump start a frozen battery. It could explode and cause serious injury. ● Your vehicle has an automatic engine cooling fan. It could come on at any time. Keep hands and other objects away from it. WCE0054 WARNING Always follow the instructions below.
PUSH STARTING ● Make sure the jumper cables do not touch moving parts in the engine compartment and that the cable clamps do not contact any other metal. 5. Start the engine of the booster vehicle and let it run for a few minutes. 6. Keep the engine speed of the booster vehicle at about 2,000 rpm, and start the engine of the vehicle being jump started. CAUTION Do not keep the starter motor engaged for more than 10 seconds.
TOWING YOUR VEHICLE 3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or coolant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen. 4. Open the engine hood. WARNING If steam or water is coming from the engine, stand clear to prevent getting burned. 5. Visually check drive belts for damage or looseness. Also check if the cooling fan is running.
For information about towing your vehicle behind a recreational vehicle (RV), refer to “Flat towing” in the “Technical and consumer information” section of this manual. Two-wheel drive models NISSAN recommends that your vehicle be towed with the driving (rear) wheels off the ground or place the vehicle on a flat bed truck as illustrated.
If the speed or distance must necessarily be greater, remove the propeller shaft before towing to prevent damage to the transmission. WSD0097 Four-wheel drive models NISSAN recommends that towing dollies be used when towing your vehicle or place the vehicle on a flat bed truck as illustrated. CAUTION ● Never tow 4WD models with any of the wheels on the ground as this may cause serious and expensive damage to the transfer case and transmission.
● Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged. CAUTION LCE0083 VEHICLE RECOVERY (freeing a stuck vehicle) Pulling a stuck vehicle If your vehicle is stuck in sand, snow, mud, etc., use a tow strap or other device designed specifically for vehicle recovery. Always follow the recovery device manufacturer’s instructions. Attach the tow strap to the towing hook.
7 Appearance and care Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Glass . . . . . . . . . . . . . . . . . . . . . . .
CLEANING EXTERIOR In order to maintain the appearance of your vehicle, it is important to take proper care of it. To protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads. ● when contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface. ● when dust or mud builds up on the surface.
REMOVING SPOTS CAUTION Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store. When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electrical conductors, radio antenna elements or rear window defroster elements.
CLEANING INTERIOR Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry, soft cloth. ● Never use fabric protectors unless recommended by the manufacturer. Regular care and cleaning is required in order to maintain the appearance of the leather.
CORROSION PROTECTION SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemental restraint system” section of this manual. WARNING Do not allow wet seat belts to roll up in the retractor. NEVER use bleach, dye or chemical solvents to clean the seat belts, since these materials may severely weaken the seat belt webbing.
● Never allow water or other liquids to come in contact with electronic components inside the vehicle as this may damage them. Chemicals used for road surface de-icing are extremely corrosive. They accelerate corrosion and deterioration of underbody components such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders. In winter, the underbody must be cleaned periodically.
8 Maintenance and do-it-yourself Maintenance requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Explanation of general maintenance items . . . . . . . . . 8-2 Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Engine compartment check locations . . . . . . . . . . . . . . . . 8-6 Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE REQUIREMENTS Your new NISSAN has been designed to have minimum maintenance requirements with long service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emission and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.
When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary.
Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Under the hood and vehicle The maintenance items listed here should be checked periodically (for example, each time you check the engine oil or refuel). Battery* Check the fluid level in each cell.
MAINTENANCE PRECAUTIONS When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. WARNING ● Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving. Move the shift selector lever to P (Park).
ENGINE COMPARTMENT CHECK LOCATIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Battery Fuse/fusible link box Transmission dipstick Engine oil filler cap Brake fluid reservoir Windshield washer fluid reservoir Air cleaner Drive belt location Radiator cap Power steering fluid reservoir Engine oil dipstick Engine coolant reservoir NOTE: Engine cover removed for clarity.
ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with Genuine NISSAN Long Life Antifreeze/Coolant to provide year-round antifreeze and coolant protection.The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary. WARNING ● Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down.
ENGINE OIL If the cooling system frequently requires coolant, have it checked by a NISSAN dealer. Engine coolant must be disposed of properly. Check your local regulations. CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheating. WARNING ● To avoid the danger of being scalded, never change the coolant when the engine is hot.
CAUTION Oil level should be checked regularly. Operating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. LDI0371 5. Remove the dipstick again and check the oil level. It should be between the H (High) and B . This is the normal operL (Low) marks s ating oil level range. If the oil level is below A , remove the oil filler cap the L (Low) mark s and pour recommended oil through the C. opening. Do not overfill s 6.
If the oil filter is to be changed, remove and replace it at this time. See “Changing engine oil filter” later in this section. WARNING ● Prolonged and repeated contact with used engine oil may cause skin cancer. ● Try to avoid direct skin contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as possible. ● Keep used engine oil out of reach of children. CAUTION Be careful not to burn yourself. The engine oil may be hot. ● Waste oil must be disposed of properly.
5-SPEED AUTOMATIC TRANSMISSION FLUID 5. Wipe the engine oil filter sealing surface with a clean rag. Be sure to remove any old gasket material remaining on the sealing surface of the engine. 6. Coat the gasket on the new filter with clean engine oil. 7. Screw on the oil filter until a slight resistance is felt, then tighten an additional 2/3 turn. 8. Start the engine and check for leakage around the oil filter. Correct as required. 9. Turn the engine off and wait more than 10 minutes. Check the oil level.
BRAKE FLUID WINDOW WASHER FLUID For further brake fluid specification information, refer to “Capacities and recommended fuel/lubricants” in the “Technical and consumer information” section of this manual. WARNING ● Use only new fluid from a sealed container. Old, inferior or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system and affect the vehicle’s stopping ability. ● Be sure to clean the filler cap before removing.
BATTERY Refill the reservoir more frequently when driving conditions require an increased amount of window washer fluid. ● Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water. ● When working on or near a battery, always wear suitable eye protection and remove all jewelry. Recommended fluid is Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent. ● Make certain the terminal connections are clean and securely tightened.
Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer. WDI0224 1. Remove the battery caps with a screwdriver as shown. Use a cloth to protect the battery case. LDI0302 2. Check the fluid level in each cell.
VARIABLE VOLTAGE CONTROL SYSTEM DRIVE BELT If you add electrical accessories to your vehicle A located near the ground it to the body ground s battery along the negative battery cable. WDI0566 CAUTION ● Do not ground accessories directly to the battery terminal. Doing so will bypass the variable voltage control system and the vehicle battery may not charge completely. ● Use electrical accessories with the engine running to avoid discharging the vehicle battery.
SPARK PLUGS 1. Visually inspect the belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer. WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. 2. Have the belt checked regularly for condition and tension in accordance with the maintenance schedule found in the “NISSAN Service and Maintenance Guide”.
AIR CLEANER WARNING ● Operating the engine with the air cleaner removed can cause you or others to be burned. The air cleaner not only cleans the air, it stops the flame if the engine backfires. If it isn’t there, and the engine backfires, you could be burned. Do not drive with the air cleaner removed, and be careful when working on the engine with the air cleaner removed. LDI0376 The air cleaner filter should not be cleaned and reused.
WDI0623 LDI0387 2. Open the glove box, then remove the three upper glove box screws. Remove the glove box assembly from the instrument panel to access the in-cabin microfilter cover. 3. Remove the filter cover bolt and remove the filter cover. LDI0404 NOTE: The filters are marked with air flow arrows. The end of the filter with the arrow should face the rear of the vehicle. The arrows should face downward. 4. Insert the first filter into the housing and slide it over to the right.
WINDSHIELD WIPER BLADES CLEANING CAUTION If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. ● After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened. Clean the outside of the windshield with a washer solution or a mild detergent. Your windshield is clean if beads do not form when rinsing with clear water.
WDI0629 If you wax the surface of the hood, be careful not A . This may to let wax get into the washer nozzle s cause clogging or improper windshield washer operation. If wax gets into the nozzle, remove it B.
LDI0379 Rear window wiper blade 1 s Lift the wiper arm away from the rear window. 2 s Push the wiper blade in and pivot until the blade becomes free. 3 s Insert a new blade onto the wiper arm and snap into place.
BRAKES FUSES If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate maintenance schedule information in the “NISSAN Service and Maintenance Guide”. The front and rear disc-type brakes self-adjust every time the brake pedal is applied.
3. Remove the fuse box cover by pushing the tab and lifting the cover up. 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. LDI0457 If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration. This will not affect the performance of the fuse. Make sure the fuse is installed in the fuse box securely.
3. Pull the fuse box cover to remove. 4. Remove the fuse with the fuse puller. WDI0452 A , replace it with a new 5. If the fuse is open s B. fuse s 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links. If any of these fusible links are melted, replace with only genuine NISSAN parts.
WDI0452 Type A A , replace it with an 5. If the fuse is open s B. equivalent good fuse s LDI0456 Type B 6. Push the fuse box cover to install. 7. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer.
BATTERY REPLACEMENT button, then the 5. Press the button two or three times to check the keyfob operation. If the battery is removed for any reason other than replacement, perform step 5. ● An improperly disposed battery can hurt the environment. Always confirm local regulations for battery disposal. ● The keyfob is water-resistant; however, if it does get wet, immediately wipe completely dry. ● The operational range of the keyfob extends to approximately 33 ft (10 m) from the vehicle.
INTELLIGENT KEY BATTERY Replace the battery in the Intelligent Key as follows: 1. Remove the mechanical key from the Intelligent Key. A into the slit s B 2. Insert a small screwdriver s of the corner and twist it to separate the upper part from the lower part. Use a cloth to protect the casing. 3. Replace the battery with a new one. Recommended battery: CR2025 or equivalent. WDI0621 ● Do not touch the internal circuit and electric terminals as doing so could cause a malfunction. C s D. 4.
LIGHTS Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. HEADLIGHTS Replacing the halogen headlight bulb The headlight is a semi-sealed beam type which uses a replaceable headlight (halogen) bulb. Because the headlight assembly must be removed from the vehicle for bulb replacement, see your NISSAN dealer.
FOG LIGHTS (if so equipped) Replacing the fog light bulb NOTE: To adjust the fog light vertical aim: Access the aiming screw from underneath the front bumper. The aiming screw is located on the bottom of the fog light housing. Turn the screw clockwise to raise the pattern. Turn the screw counterclockwise to lower the pattern. CAUTION ● High pressure halogen gas is sealed inside the halogen bulb. The bulb may break if the glass envelope is scratched or the bulb is dropped.
EXTERIOR AND INTERIOR LIGHTS Item Wattage (W) Bulb No. High 60/65 HB3/9005 Low 51/55 HB4/9006 Park/Turn 8/27 3457K 3.8 194 Always check with the Parts Department at a NISSAN dealer for the latest parts information. Headlight assembly* Sidemarker Side turn signal light* (if so equipped) (LED) — Front fog light 27 881 Puddle lamp 13 906 Room/map lights 8 – Personal lights 6 WXW52 Footwell* 3.4 158 Glove box light* 3.4 158 Vanity mirror light 1.8 – Step light 3.
1. 2. 3. 4. Room/map light Front personal lights Step light Puddle lamp/Side turn signal light (if so equipped) 5. High-mount stoplight 6. Cargo light 7. License plate light 8. Rear combination light 9. Headlight assembly 10. Fog light WDI0263 Replacement procedures LDI0383 All other lights are either type A, B, C or D. When replacing a bulb, first remove the lens, lamp and/or cover.
LDI0364 Personal lights 1 to protect the housing. Use a cloth s LDI0385 Vanity mirror 1 to protect the housing. Use a cloth s LDI0389 Room/map lights 1 to protect the housing.
LDI0341 Step light 1 to protect the housing. Use a cloth s LDI0388 Puddle light 1 to protect the housing. Use a cloth s WDI0233 Cargo light 1 to protect the housing.
WHEELS AND TIRES If you have a flat tire, see the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated.
conditioner and audio systems” section, “Tire Pressure Monitoring System (TPMS)” in the “Starting and driving” section, and “Flat tire” in the “In case of emergency” section. Tire inflation pressure Check the tire pressures (including the spare) often and always prior to long distance trips. The recommended tire pressure specifications are shown on the F.M.V.S.S./C.M.V.S.S. certification label or the Tire and Loading Information label under the “Cold Tire Pressure” heading.
6 s Spare tire size or compact spare tire size (if so equipped). LDI0485 Tire and loading information label 1 s Seating capacity: The maximum number of occupants that can be seated in the vehicle. 2 s Vehicle load limit: See loading information in the “Technical and consumer information” section. 3 s Original tire size: The size of the tires originally installed on the vehicle at the factory. 4 s Cold tire pressure: Inflate the tires to this pressure when the tires are cold.
4. Read the tire pressure on the gauge stem and compare to the specification shown on the Tire and Loading Information label. 5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. 6. Install the valve stem cap. LDI0393 Checking tire pressure 7. Check the pressure of all other tires, including the spare.
WDI0394 Example TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall. WDI0395 Example 1 Tire size (example: P215/65R15 95H) s 1.
3 Tire ply composition and material s The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 4 Maximum permissible inflation press sure WDI0396 Example 2 TIN (Tire Identification Number) for a s new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the 9Department Of Transportation.
7 The word “radial” s The word “radial” is shown if the tire has radial structure. 8 Manufacturer or brand name s ● For additional information regarding tires, refer to “Important Tire Safety Information” (US) or “Tire Safety Information” (Canada) in the Warranty Information Booklet. Manufacturer or brand name is shown. All season tires TYPES OF TIRES NISSAN specifies All Season tires on some models to provide good performance all year, including snowy and icy road conditions.
Use of tire chains may be prohibited according to location. Check the local laws before installing tire chains. When installing tire chains, make sure they are the proper size for the tires on your vehicle and are installed according to the chain manufacturer’s suggestions. Use only SAE class “S” chains. Class “S” chains are used on vehicles with restricted tire to vehicle clearance.
Wheel nut tightening torque: ● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced. 98 ft-lb (133 N·m) The wheel nuts must be kept tightened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. ● Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be obvious.
Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “Technical and consumer information” section of this manual.
If excessive tire wear is found, it is recommended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact a NISSAN dealer. Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required. ● Do not use abrasive cleaners when washing the wheels.
9 Technical and consumer information Capacities and recommended fuel/lubricants . . . . . . . . . 9-2 Fuel recommendation (without Flexible Fuel Vehicle option). . . . . . . . . . . . . . 9-3 Flexible fuel vehicle (FFV) fuel recommendation (if so equipped). . . . . . . . . . . . . . . . . 9-4 Engine oil and oil filter recommendations . . . . . . . . . . 9-6 Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 Specifications. . . . . . .
CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity.
FUEL RECOMMENDATION (without Flexible Fuel Vehicle option) Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). CAUTION ● Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85. ● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.
E–85 fuel E-85 fuel is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. E-85 can only be used in a Flexible Fuel Vehicle (FFV). Do not use E-85 in your vehicle. U.S. government regulations require fuel ethanol dispensing pumps to be identified by a small, square, orange and black label with the common abbreviation or the appropriate percentage for that region.
Unleaded Gasoline Only. This section only covers those subjects that are unique to Flexible Fuel vehicles. CAUTION Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85. Ethanol Fuel (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING ● Ethanol vapors are extremely flammable and could cause serious personal injury.
Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be operated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage.
the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: ● repeated short distance driving at cold outside temperatures ● driving in dusty conditions ● extensive idling ● towing a trailer ● stop and go commuting Refer to the “NISSAN Service and Maintenance Guide” for the maintenance schedule.
SPECIFICATIONS ENGINE Model VK56DE Type Gasoline, 4-cycle, DOHC Cylinder arrangement 8-cylinder, V-block, Slanted at 90° Bore x Stroke in (mm) 3.858 x 3.622 (98 x 92) Displacement cu in (cm3) 338.78 (5,552) Firing order 1–8–7–3–6–5–4–2 Idle speed A/T (in “N” position) Ignition timing (degree B.T.D.C. at idle speed) See the “Emission Control Information label” on the underside of the hood.
WHEELS AND TIRES DIMENSIONS AND WEIGHTS Wheels Overall length in (mm) 207.7 (5,275) 18 x 8.0J Overall width in (mm) 79.4 (2,016) 20 x 8.0J Overall height 2wd with roof rack in (mm) 77.8 (1,977) 4wd with roof rack in (mm) 78.6 (1,998) 18 inch tire in (mm) 67.9 (1,725) 20 inch tire in (mm) 68.1 (1,729) 18 inch tire in (mm) 67.9 (1,725) 20 inch tire in (mm) 68.
WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY VEHICLE IDENTIFICATION When planning to drive your NISSAN vehicle in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available.
WTI0095 ENGINE SERIAL NUMBER The number is stamped on the engine as shown. WTI0099 WTI0189 F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL EMISSION CONTROL INFORMATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification label is affixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.
INSTALLING FRONT LICENSE PLATE WTI0100 WTI0188 LTI0093 TIRE AND LOADING INFORMATION LABEL AIR CONDITIONER SPECIFICATION LABEL Use the following steps to mount the front license plate: The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. The air conditioner specification label is affixed to the underside of the hood as shown. 1. Make holes on the plastic finisher at the location mark (small dimple) using a 0.20 in (5 mm) drill.
VEHICLE LOADING INFORMATION WARNING ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. ● Be sure everyone in your vehicle is in a seat and using a seat belt properly.
Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the XXX amount equals 1400 lbs.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.
● Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury. LOADING TIPS ● The GVW must not exceed GVWR or GAWR as specified on the F.M.V.S.S./C.M.V.S.S. certification label. ● Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR.
TOWING A TRAILER WARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and performance and may lead to accidents. CAUTION ● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km). Your engine, axle or other parts could be damaged. ● For the first 500 miles (800 km) that you tow a trailer, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.
Temperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automatically decrease engine power. Vehicle speed may decrease under high load. Plan your trip carefully to account for trailer and vehicle load, weather and road conditions.
Towing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load. The vehicle and trailer need to be weighed to confirm the vehicle is within the GVWR, Front GAWR, Rear GAWR, Gross Combined Weight Rating (GCWR) and Towing capacity.
The available towing capacity may be less than the maximum towing capacity due to the passenger and cargo load in the vehicle. Remember to keep trailer tongue weight between 10 - 15% of the trailer weight. If the tongue load becomes excessive, rearrange the cargo to obtain the proper tongue load. Do not exceed the 10 - 15% tongue weight specification even if the calculated available tongue weight is greater than 15%.
TOWING SAFETY Trailer hitch Your vehicle may be equipped with an optional trailer tow package. The trailer tow package includes a receiver-type frame mounted hitch. This hitch is rated for the maximum towing capacity of this vehicle when the proper towing equipment is used. Choose a proper ball mount and hitch ball that is rated for the trailer to be towed. Genuine Nissan ball mounts and hitch balls are available from your NISSAN dealer.
lbs. gross weight, 1,000 lbs. tongue weight. This means that without using a weight distributing ballmount, the receiver is only designed to carry 5,000 lbs. When hooking up a trailer using a weight distributing hitch, always refer to the hitch manufacturer’s instructions. 1. Park unloaded vehicle on a level surface. With the ignition on and the doors closed, allow the vehicle to stand for several minutes so that it can level. 2.
CAUTION ● Special hitches which include frame reinforcements are required for towing above 2,000 lb (907 kg). Suitable genuine NISSAN hitches, ball mounts and hitch balls for pickup trucks and sport utility vehicles are available at a NISSAN dealer. ● The hitch should not be attached to or affect the operation of the impactabsorbing bumper. ● Do not use axle-mounted hitches. ● Do not modify the vehicle exhaust system, brake system, etc. to install a trailer hitch.
Trailer brakes If your trailer is equipped with a braking system, make sure it conforms to federal and/or local regulations and that it is properly installed. WARNING Never connect a trailer brake system directly to the vehicle brake system. LTI0117 example Electric trailer brake controller LTI0122 2. Apply the parking brake to access the jumper harness connector. Trailers equipped with electric brakes may require the installation of an aftermarket trailer brake controller.
Wire color designation for electric trailer brake controller jumper harness. LTI0115 3. Locate the jumper harness connector under the lower portion of the instrument panel. The connector is taped to the wiring harness 1 as indicated. s ● The connector is marked with a white tag with “electric brake connector”. WIRE COLOR NOTE RED/GREEN Vehicle stop lamp switch to trailer brake controller. BLACK Brake controller ground (-). BROWN/WHITE Trailer brake controller switched output.
Pre-towing tips ● Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched. Do not drive the vehicle if it has an abnormal nose-up or nose-down condition; check for improper tongue load, overload, worn suspension or other possible causes of either condition. ● Always secure items in the trailer to prevent load shift while driving. ● Keep the cargo load as low as possible in the trailer to keep the trailer center of gravity low.
To drive away: 1. Start the vehicle. 2. Apply and hold the brake pedal. 3. Shift the transmission into gear. 4. Release the parking brake. 5. Drive slowly until the vehicle and trailer are clear from the blocks. 6. Apply and hold the brake pedal. 7. Have someone retrieve and store the blocks. ● When going down a hill, shift into a lower gear and use the engine braking effect.
● Do not use cruise control while towing a trailer. ● Some states or provinces have specific regulations and speed limits for vehicles that are towing trailers. Obey the local speed limits. ● Check your hitch, trailer wiring harness connections, and trailer wheel lug nuts after 50 miles (80 km) of travel and at every break. ● When stopped in traffic for long periods of time in hot weather, put the vehicle in the P (Park) position.
SNOW PLOW Automatic Transmission To tow a vehicle equipped with an automatic transmission, an appropriate vehicle dolly MUST be placed under the towed vehicle’s drive wheels. Always follow the dolly manufacturer’s recommendations when using their product. UNIFORM TIRE QUALITY GRADING WARNING Do not use this vehicle for snowplowing. Installing a snowplow may affect vehicle handling. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.
EMISSION CONTROL SYSTEM WARRANTY WARNING The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature A, B and C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat, and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
REPORTING SAFETY DEFECTS (US only) READINESS FOR INSPECTION/ MAINTENANCE (I/M) TEST If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN.
EVENT DATA RECORDERS 8. Stop the vehicle. Place the transmission selector lever in the P (Park) or N (Neutral) position. 9. Turn the engine off. 10. Repeat steps 1 - 8 at least one more time. If steps 1 through 7 are interrupted, repeat the preceding step. Any safe driving mode is acceptable between steps. Do not stop the engine until step 7 is completed. This vehicle is equipped with an Event Data Recorder (EDR).
OWNER’S MANUAL/SERVICE MANUAL ORDER INFORMATION A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle. Filled with wiring diagrams, illustrations and step-by-step diagnostic and adjustment procedures, this manual is the same one used by the factory-trained technicians working at NISSAN dealerships. Also available are genuine NISSAN Owner’s Manuals, and genuine NISSAN Service and Owner’s Manuals for older NISSAN models.
Why should you take a chance? It’s your right! In over 40 states, the law says you must be advised if non-genuine parts are used to repair your vehicle. And some states have enacted laws that restrict insurance companies from authorizing the use of non-genuine collision parts during the new vehicle warranty. These laws help protect you, so you can take action to protect yourself. If you should need further information visit us at: www.nissanusa.com (for U.S. customers) or www.nissan.
10 Index 4WD warning light . . . . . . . . . . . . . . .2-16 A Active Head Restraint . . . . . . . . . . . . . .1-9 Adjusting pedal position . . . . . . . . . . . .3-27 Air bag (See supplemental restraint system) . . . . . . . . . . . . . . . . . . . . .1-48 Air bag system Front (See supplemental front impact air bag system) . . . . . . . . . . . . . . .1-55 Air bag warning labels . . . . . . . . . . . . .1-63 Air bag warning light. . . . . . . . . . .1-63, 2-18 Air cleaner housing filter . . . . . . . . .
C Capacities and recommended fuel/lubricants. . . . . . . . . . . . . . . . . . .9-2 Captain’s chair adjustment (2nd row). . . . . .1-5 Car phone or CB radio . . . . . . . . . . . . .4-93 Cargo light . . . . . . . . . . . . . . . . . . .2-60 Cargo (See vehicle loading information) . . .9-13 CD care and cleaning . . . . . . . . . . . . .4-73 CD changer (See audio system). . . . . . . .4-52 CD player (See audio system) . . . . . . . . .4-60 Child restraint with top tether strap . . . . . .
Eyeglass case . . . . . . . . . . . . . . . . . .2-44 F Flashers (See hazard warning flasher switch). . . . . .2-36 Flat tire . . . . . . . . . . . . . . . . . . . . . .6-2 Floor mat positioning aid . . . . . . . . . . . . .7-4 Fluid Brake fluid . . . . . . . . . . . . . . . . . .8-12 Capacities and recommended fuel/lubricants. . . . . . . . . . . . . . . . .9-2 Engine coolant . . . . . . . . . . . . . . . .8-7 Engine oil . . . . . . . . . . . . . . . . . . .8-8 Power steering fluid. . . . . . . . . . . . .
J Jump starting . . . . . . . . . . . . . . . . . . .6-8 K Key . . . . . . . . . . . . . . . . . . . . . . Keyfob battery replacement . . . . . . . . . Keyless entry With Intelligent Key system (See Intelligent Key system) . . . . . . . Keyless entry system (See remote keyless entry system) . . . . . . . . . . . . . . . . . Keys, For Intelligent Key system . . . . . . . . .3-2 .8-26 .3-16 . .3-6 . .3-2 L Labels Air conditioner specification label . . C.M.V.S.S. certification label . . . . .
NISSAN vehicle immobilizer system. . . . . . . . . . . . . . . .2-29, 3-3, 5-11 NISSAN voice recognition system . . . . . .4-117 O Octane rating (See fuel octane rating) . . . Odometer . . . . . . . . . . . . . . . . . . . Oil Capacities and recommended fuel/lubricants. . . . . . . . . . . . . . . Changing engine oil . . . . . . . . . . . Changing engine oil filter . . . . . . . . . Checking engine oil level . . . . . . . . Engine oil . . . . . . . . . . . . . . . . .
Second row bench seats . . . . . . . . . .1-6 Second row captain’s chair . . . . . . . . .1-5 Third row power folding seats . . . . . . .1-15 Seat belt Child safety . . . . . . . . . . . . . . . . .1-18 Infants and small children . . . . . . . . .1-19 Injured Person. . . . . . . . . . . . . . . .1-20 Larger children . . . . . . . . . . . . . . .1-19 Precautions on seat belt usage . . . . . .1-16 Pregnant women . . . . . . . . . . . . . .1-20 Pre-tensioner seat belt system. . . . . . .
Tire Flat tire . . . . . . . . . . . . . . . . . . . .6-2 Spare tire . . . . . . . . . . . . . . . . . . .6-3 Tire chains . . . . . . . . . . . . . . . . . .8-40 Tire placard . . . . . . . . . . . . . . . . .9-12 Tire pressure . . . . . . . . . . . . . . . .8-34 Tire rotation . . . . . . . . . . . . . . . . .8-41 Tires of 4-wheel drive. . . . . . . . . . . .8-43 Types of tires . . . . . . . . . . . . . . . .8-40 Uniform tire quality grading. . . . . . . . .9-29 Wheels and tires . . . . . . . . . . . . . .
Wiper Rear window wiper and washer switches . . . . . . . . . . . . . . . . . . .2-31 Windshield wiper and washer switch . . .2-30 Wiper blades . . . . . . . . . . . . . . . .
GAS STATION INFORMATION RECOMMENDED FUEL (without Flexible Fuel Vehicle option): For additional information, see “Capacities and recommended fuel/lubricants in the “Technical and consumer information” section. Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). FLEXIBLE FUEL VEHICLE (FFV) FUEL RECOMMENDATION (if so equipped): CAUTION ● Only vehicles with the E-85 filler door label can operate on E-85.
QUICK REFERENCE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
