2014 NISSAN TITAN ® 2014 TITAN OWNER’S MANUAL A60-D A60-D Printing : September 2013 (19) 0A60U0 OM14E0A60U0 Publication No.: OM1E Printed in U.S.A. For your safety, read carefully and keep in this vehicle.
FOREWORD Welcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you understand the operation and maintenance of your vehicle so that you may enjoy many miles (kilometers) of driving pleasure. Please read through this manual before operating your vehicle.
WHEN READING THE MANUAL For descriptions specified for four-wheel drive mark is placed at the beginmodels, a ning of the applicable sections/items. As with other vehicles with features for off-road use, failure to operate four-wheel drive models correctly may result in loss of control or an accident. Be sure to read “Driving safety precautions” in the “Starting and driving” section of this manual.
CALIFORNIA PROPOSITION 65 WARNING WARNING APD1005 Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
NISSAN CUSTOMER CARE PROGRAM NISSAN CARES . . . Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Your NISSAN dealer is always available to assist you with all your automobile sales and service needs.
Table of Contents Illustrated table of contents 0 Safety—Seats, seat belts and supplemental restraint system 1 Instruments and controls 2 Pre-driving checks and adjustments 3 Monitor, climate, audio, phone and voice recognition systems 4 Starting and driving 5 In case of emergency 6 Appearance and care 7 Maintenance and do-it-yourself 8 Technical and consumer information 9 Index 10
0 Illustrated table of contents Air bags, seat belts and child restraints . . . . . . . . . . . . . . 0-2 Exterior front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-3 Exterior rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-4 Passenger compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-5 Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-6 Engine compartment check locations . . . . .
AIR BAGS, SEAT BELTS AND CHILD RESTRAINTS 1. 2. 2nd row seat belts (P. 1-15) Roof-mounted curtain side-impact and rollover supplemental air bag (P. 1-47) 3. Front seat belts (P. 1-15) 4. Front-seat Active Head Restraints 5. Supplemental front-impact air bags (P. 1-47) 6. Seats (P. 1-2) 7. Occupant classification sensor (pressure sensor) (P. 1-56) 8. Seat belt with pretensioner (P. 1-60) 9. Front seat-mounted side-impact supplemental air bag (P. 1-47) 10. LATCH (Lower Anchors and Tethers for Children) (P.
EXTERIOR FRONT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Engine hood (P. 3-11) Windshield wiper and washer switch (P. 2-27) Windshield (P. 8-20) Moonroof (if so equipped) (P. 2-54) Power windows (P. 2-51) Door locks, keyfob, keys (P. 3-3, 3-7, 3-2) Mirrors (P. 3-16) Tire pressure (P. 9-12) Flat tire (P. 6-2) Tire chains (P. 8-40) Replacing bulbs (P. 8-30) Headlight and turn signal switch (P. 2-30) Fog light switch (if so equipped) (P. 2-33) Tow hooks (if so equipped) (P.
EXTERIOR REAR 1. 2. 3. 4. 5. 6. 7. 8. 9. Rear sliding window (if so equipped) (P. 2-53) Vehicle loading (P. 9-13) Tailgate/Truckbox (P. 3-21) Trailer hitch/Towing (if so equipped) (P. 9-24) Replacing bulbs (P. 8-30) Bedside storage compartment (if so equipped) (P. 2-50) Fuel-filler cap, fuel recommendation (P. 3-12, P. 9-3, 9-5) Fuel-filler door (P. 3-12) Child safety rear door lock (Crew Cab models only) (P. 3-7) See the page number indicated in parentheses for operating details.
PASSENGER COMPARTMENT 1. 2. 3. 4. 5. 6. 7. 8. 9. DVD entertainment system (if so equipped) (P. 4-73) Moonroof (if so equipped) (P. 2-54) Map lights (if so equipped) (P. 2-58) Sun visors (P. 3-15) HomeLink姞 (if so equipped) (P. 2-58) Glove box (P. 2-45) Cup holders (P. 2-47) Front seats (P. 1-2) Folding rear bench seat (P. 1-13) See the page number indicated in parentheses for operating details.
INSTRUMENT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. LIC2437 0-6 Illustrated table of contents Vents (P. 4-17) Headlight/fog light (if so equipped)/turn signal switch (P. 2-30) Steering wheel switch for audio control/Bluetooth姞 Hands-Free Phone System (if so equipped) (P. 4-71, P. 4-83, P. 4-98, P. 4-109) Instrument brightness control (P. 2-33) Driver supplemental air bag/horn (P. 1-47, P. 2-34) Meters, gauges and warning/indicator lights (P.
15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. Front passenger air bag status light (P. 1-56) Power outlet (P. 2-39) Heated seat switch (if so equipped) (P. 2-34) Vehicle Dynamic Control (VDC) off switch (P. 2-36) Tow mode switch (P. 2-38) Electronic locking rear differential (E-Lock) system switch (if so equipped) (P.2-36) Shift selector (console) (if so equipped) (P. 5-16) Hazard warning flasher switch (P. 6-2) Power outlet (P. 2-39) 4WD shift switch (if so equipped) (P. 5-27) Ignition switch (P.
ENGINE COMPARTMENT CHECK LOCATIONS 1. 2. 3. 4. 5. 6. Battery (P. 8-14) Fuse/fusible link box (P. 8-22) Transmission dipstick (P. 8-11) Engine oil filler cap (P. 8-9) Brake fluid reservoir (P. 8-13) Windshield-washer fluid reservoir (P. 8-13) 7. Air cleaner (P. 8-18) 8. Drive belt location (P. 8-16) 9. Radiator cap (P. 8-7) 10. Power steering fluid reservoir (P. 8-12) 11. Engine oil dipstick (P. 8-9) 12. Engine coolant reservoir (P. 8-7) NOTE: Engine cover removed for clarity.
WARNING/INDICATOR LIGHTS Warning light or Name Page Anti-lock Braking System (ABS) warning light 2-14 Warning light Name Page Indicator light Name Page 4WD warning light model) ( 2-16 Front passenger air bag status light 2-19 Low fuel warning light 2-16 High beam indicator light (Blue) 2-19 Automatic transmission check warning light 2-14 Low tire pressure warning light 2-16 Malfunction indicator light (MIL) 2-19 Automatic transmission park warning model) light ( 2-14 Master warn
MEMO 0-10 Illustrated table of contents
1 Safety—Seats, seat belts and supplemental restraint system Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front manual captain’s chair seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Front manual bench seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Front power seat adjustment (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEATS ● The seatback should not be reclined any more than needed for comfort. Seat belts are most effective when the passenger sits well back and straight up in the seat. If the seatback is reclined, the risk of sliding under the lap belt and being injured is increased. CAUTION When adjusting the seat positions, be sure not to contact any moving parts to avoid possible injuries and/or damage. ARS1152 WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous.
LRS0419 LRS0420 Forward and backward Reclining Pull the lever up and hold it while you slide the seat forward or backward to the desired position. Release the lever to lock the seat in position. To recline the seatback, pull the lever up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position.
LRS0427 Reclining To recline the seatback, pull the lever up and lean back. To bring the seatback forward, pull the lever up and lean your body forward. Release the lever to lock the seatback in position. The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit (see “Precautions on seat belt usage” later in this section).
The reclining feature allows adjustment of the seatback for occupants of different sizes for added comfort and to help obtain proper seat belt fit. See “Precautions on seat belt usage” later in this section. Also, the seatback can be reclined to allow occupants to rest when the vehicle is stopped and the shift selector is in P (Park). LRS0634 Seat lifter (if so equipped for driver’s seat) Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion.
HEAD RESTRAINTS (1st row only) WARNING WRS0368 Type A A 䊊 B 䊊 LRS0425 Type B Stowed position Resting position ARMRESTS (if so equipped) To use the armrests on the captain’s chairs (type A, if so equipped), pull them down to the resting position. To use the center armrest on the bench seat (type B, if so equipped), pull on the tab in the center of the seat and fold it down to the resting position.
LRS2020 The illustration shows the seating positions equipped with head restraints. The first row head restraints are adjustable. 䉱 Indicates the seating position is equipped with a head restraint. LRS0887 Components WRS0134 Adjustment 1. Head restraint 2. Adjustment notches Adjust the head restraint so the center is level with the center of the seat occupant’s ears. 3. Lock knob 4.
LRS0888 To raise the head restraint, pull it up. LRS0889 To lower, push and hold the lock knob and push the head restraint down. LRS0890 Removal Use the following procedure to remove the adjustable head restraints. 1. Pull the head restraint up to the highest position. 2. Push and hold the lock knob. 3. Remove the head restraint from the seat. 4. Store the head restraint properly so it is not loose in the vehicle. 5.
Adjust the Active Head Restraints properly as described in this section. HEAD RESTRAINTS (2nd row – outboard positions only) WARNING LRS0891 Install 1. Align the head restraint stalks with the holes in the seat. Make sure the head restraint is facing the correct direction. The stalk with 1 must be installed the adjustment notches 䊊 2 . in the hole with the lock knob 䊊 2. Push and hold the lock knob and push the head restraint down. 3.
LRS2020 LRS2073 The illustration shows the seating positions equipped with head restraints. The second row head restraints are removable but not adjustable. Components 䉱 Indicates the seating position is equipped with a head restraint. 2. Lock knob 1. Head restraint 3. Stalks + Indicates the seating position is not equipped with a head restraint or adjustable headrest. LRS2074 Removal Use the following procedure to remove the head restraints. 1. Adjust the seat or seatback as necessary. 2.
FLEXIBLE SEATING WARNING ● Never allow anyone to ride in the cargo area or on the rear seats when they are in the fold-down position. In a collision, people riding in these areas without proper restraints are more likely to be seriously injured or killed. LRS2075 Install 1. Align the head restraint stalks with the holes in the seat. Make sure the head restraint is facing the correct direction. 2. Push the head restraint down until it locks in place.
WARNING ● If you fold the front passenger’s seatback flat forward to carry longer objects, be sure this cargo is properly secured and not near an air bag. In a crash, an inflating air bag might force that object toward a person. This could cause severe injury or even death. Secure objects away from the area in which an air bag would inflate. See “Precautions on supplemental restraint system” later in this section.
LRS0398 Folding the rear bench seat To fold the rear bench seat up for storage capacity behind the front seats or to remove the jacking tools from the storage area: 䊊 1 Lift up on the lever, located on the side of the seat, while lifting the front of the seat cushion up. LRS0399 2 䊊 Fold the bottom of the seat cushion toward the back of the vehicle until it locks in place.
WARNING WARNING ● When the vehicle is being used to carry cargo, properly secure all cargo to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. Be sure everyone in your vehicle is in a seat and using a seat belt properly.
SEAT BELTS SSS0136 PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly adjusted and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up every time you drive, even if your seating position includes a supplemental air bag. Most U.S.
SSS0134 WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly restrained in the rear seat and, if appropriate, in a child restraint. 1-16 Safety—Seats, seat belts and supplemental restraint system SSS0016 WARNING ● The seat belt should be properly adjusted to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident.
● Be sure the seat belt tongue is securely fastened to the proper buckle. ● Do not wear the seat belt inside out or twisted. Doing so may reduce its effectiveness. ● Do not allow more than one person to use the same seat belt. ● Never carry more people in the vehicle than there are seat belts. SSS0014 WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never put the belt behind your back, under your arm or across your neck.
PREGNANT WOMEN NISSAN recommends that pregnant women use seat belts. The seat belt should be worn snug and always position the lap belt as low as possible around the hips, not the waist. Place the shoulder belt over your shoulder and across your chest. Never run the lap/shoulder belt over your abdominal area. Contact your doctor for specific recommendations. INJURED PERSONS NISSAN recommends that injured persons use seat belts. Check with your doctor for specific recommendations.
The Emergency Locking Retractor (ELR) mode allows the seat belt to extend and retract to allow the driver and passengers some freedom of movement in the seat. The ELR locks the seat belt when the vehicle slows down rapidly or during certain impacts. The Automatic Locking Retractor (ALR) mode (child restraint mode) locks the seat belt for child restraint installation. WRS0137 2 䊊 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage.
To increase your confidence in the seat belts, check the operation as follows: WARNING When fastening the seat belts, be certain that the seatbacks are completely secured in the latched position. If they are not completely secured, passengers may be injured in an accident or sudden stop. ● Grasp the shoulder belt and pull forward quickly. The retractor should lock and restrict further belt movement.
WARNING ● After adjustment, release the adjustment button and try to move the shoulder belt anchor up and down to make sure it is securely fixed in position. ● The shoulder belt anchor height should be adjusted to the position best for you. Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident.
LRS0643 Fastening the seat belts 1 䊊 Insert the tongue into the buckle until you hear and feel the latch engage. LRS0644 2 䊊 Tighten the belt by pulling the free end of the belt away from the tongue. 1-22 Safety—Seats, seat belts and supplemental restraint system LRS0645 3 䊊 Position the lap belt low and snug on the hips as illustrated.
WARNING ● Only NISSAN seat belt extenders, made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts. ● Adults and children who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident. LRS0646 4 䊊 Loosen the belt by holding the tongue at a right angle to the belt, then pull on the belt.
CHILD SAFETY ● Periodically check to see that the seat belt and the metal components, such as buckles, tongues, retractors, flexible wires and anchors, work properly. If loose parts, deterioration, cuts or other damage on the webbing is found, the entire seat belt assembly should be replaced. WARNING Do not allow children to play with the seat belts. Most seating positions are equipped with Automatic Locking Retractor (ALR) mode seat belts.
A child restraint may be secured in the vehicle by using either the LATCH (Lower Anchor and Tethers for CHildren) system or with the vehicle seat belt. See “Child restraints” later in this section for more information. NISSAN recommends that all pre-teens and children be restrained in the rear seat. Studies show that children are safer when properly restrained in the rear seat than in the front seat.
CHILD RESTRAINTS – Infants and children should never be held on anyone’s lap. Even the strongest adult cannot resist the forces of a collision. – Do not put a seat belt around both a child and another passenger.
– Child restraint anchor points are designed to withstand loads from child restraints that are properly fitted. – Never use the anchor points for adult seat belts or harnesses. – A child restraint with a top tether strap should not be used in the front passenger seat. – Keep seatbacks as upright as possible after fitting the child restraint. – Infants and children should always be placed in an appropriate child restraint while in the vehicle.
LATCH lower anchor WARNING Failure to follow the warnings and instructions for proper use and installation of child restraints could result in serious injury or death of a child or other passengers in a sudden stop or collision: – Attach LATCH system compatible child restraints only at the locations shown in the illustration.
LRS0395 LATCH lower anchor point locations LRS0661 LATCH webbing-mounted attachment Installing child restraint LATCH lower anchor attachments LRS0662 LATCH rigid-mounted attachment When installing a child restraint, carefully read and follow the instructions in this manual and those supplied with the child restraint. LATCH compatible child restraints include two rigid or webbing-mounted attachments that can be connected to two anchors located at certain seating positions in your vehicle.
REAR-FACING CHILD RESTRAINT INSTALLATION USING LATCH Refer to all Warnings and Cautions in the “Child Safety” and “Child Restraints” sections before installing a child restraint. Follow these steps to install a rear-facing child restraint in the 2nd row seats using the LATCH system: 1. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions. LRS0393 Top tether anchor point locations Anchor points are located under the rear window behind the rear bench seat.
WRS0802 Rear-facing rigid-mounted – step 2 LRS0673 Rear-facing – step 3 3. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attachments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments. LRS0674 Rear-facing – step 4 4.
5. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 2 through 4. WARNING The three-point seat belt with Automatic Locking Retractor (ALR) must be used when installing a child restraint. Failure to use the ALR mode will result in the child restraint not being properly secured. The restraint could tip over or be loose and cause injury to a child in a sudden stop or collision.
WRS0256 Rear-facing – step 1 Refer to all Warnings and Cautions in the “Child safety” and “Child restraints” sections before installing a child restraint. Follow these steps to install a rear-facing child restraint using the vehicle seat belts in the rear seats: WRS0761 Rear-facing – step 2 2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing.
LRS0670 Rear-facing – step 4 4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0762 Rear-facing – step 5 5. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seatback while pulling up on the seat belt. 1-34 Safety—Seats, seat belts and supplemental restraint system WRS0763 Rear-facing – step 6 6.
7. Check to make sure that the child restraint is properly secured prior to each use. If the seat belt is not locked, repeat steps 1 through 6. After the child restraint is removed and the seat belt fully retracted, the ALR mode (child restraint mode) is canceled. FORWARD-FACING CHILD RESTRAINT INSTALLATION USING LATCH Refer to all Warnings and Cautions in the “Child Safety” and “Child Restraints” sections before installing a child restraint.
7. Check to make sure the child restraint is properly secured prior to each use. If the child restraint is loose, repeat steps 3 through 6. FORWARD-FACING CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS — FRONT PASSENGER AND REAR BENCH SEAT WARNING LRS0671 Forward-facing – step 4 4. For child restraints that are equipped with webbing-mounted attachments, remove any additional slack from the anchor attachments.
2. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions. The back of the child restraint should be secured against the vehicle seatback. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. If the head restraint is removed, store it in a secure place. Be sure to reinstall the head restraint when the child restraint is removed.
LRS0667 Forward-facing – step 4 4. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted. LRS0668 Forward-facing – step 5 5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. WRS0681 Forward-facing – step 6 6.
9. Check to make sure the child restraint is properly secured prior to each use. If the seat belt is not locked, repeat steps 3 through 8. WRS0698 Forward-facing – step 8 8. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the seat belt path. The child restraint should not move more than 1 inch (25 mm), from side to side. Try to tug it forward and check to see if the seat belt holds the restraint in place.
● NISSAN recommends that child restraints be installed in the rear seat. However, if you must install a forward facing child restraint in the front center bench seat, follow these instructions carefully. ● A child restraint with a top tether strap should not be used in the front passenger seat. WRS0256 FORWARD-FACING CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS — FRONT BENCH CENTER POSITION WARNING ● Never install a rear-facing child restraint in the front passenger seat.
2. Position the child restraint on the seat. Always follow the child restraint manufacturer’s instructions. The back of the child restraint should be secured against the vehicle seat back. If necessary, adjust or remove the head restraint to obtain the correct child restraint fit. See “Head restraints” earlier in this section. If the head restraint is removed, store it in a secure place. Be sure to install the head restraint when the child restraint is removed.
6. Check to make sure the child restraint is properly secured prior to each use. If the seat belt is not locked, repeat steps 3 through 5. WRS0917 Forward-Facing — step 5 5. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the seat belt path. The child restraint should not move more than 1 inch (25 mm), from side to side. Try to tug it forward and check to see if the seat belt holds the restraint in place.
2. Position the top tether strap over the top of the seatback and under the head restraint. 2 to the tether 3. Secure the tether strap 䊊 3 on the seat directly behind anchor point 䊊 the child restraint. 4. Return the seatback to the locked position. – Make sure the shoulder belt is not behind the child or under the child’s arm. – A booster seat must only be installed in a seating position that has a lap/shoulder belt. 5.
LRS0455 LRS0453 LRS0464 Booster seats of various sizes are offered by several manufacturers. When selecting any booster seat, keep the following points in mind: ● Choose only a booster seat with a label certifying that it complies with Federal Motor Vehicle Safety Standard 213 or Canadian Motor Vehicle Safety Standard 213. ● Check the booster seat in your vehicle to be sure it is compatible with the vehicle’s seat and seat belt system.
● Make sure the child’s head will be properly supported by the booster seat or vehicle seat. The seatback must be at or above the center of the child’s ears. For example, if a 1 is chosen, the low back booster seat 䊊 vehicle seatback must be at or above the center of the child’s ears. If the seatback is lower than the center of the child’s ears, a 2 should be used.
If the seating position does not have an adjustable head restraint and it is interfering with the proper booster seat fit, try another seating position or a different booster seat. 4. Position the lap portion of the seat belt low and snug on the child’s hips. Be sure to follow the booster seat manufacturer’s instructions for adjusting the seat belt routing. LRS0454 Front passenger position 3. The booster seat should be positioned on the vehicle seat so that it is stable.
SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System (SRS) section contains important information concerning the following systems: ● Driver and passenger supplemental frontimpact air bag (NISSAN Advanced Air Bag System) ● Front seat-mounted side-impact supplemental air bag ● Roof-mounted curtain side-impact and rollover supplemental air bag ● Seat belt with pretensioner Supplemental front-impact air bag system: The NISSAN Advanced Air Bag System can
● The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The Advanced Air Bag System monitors the severity of a collision and seat belt usage then inflates the air bags as needed. Failure to properly wear seat belts can increase the risk or severity of injury in an accident. WRS0031 WARNING ● The front air bags ordinarily will not inflate in the event of a side impact, rear impact, rollover, or lower severity frontal collision.
ARS1133 ARS1041 WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations.
ARS1042 WARNING ● Children may be severely injured or killed when the front air bags, side air bags or curtain and rollover air bags inflate if they are not properly restrained. Pre-teens and children should be properly restrained in the rear seat, if possible.
ARS1045 WRS0431 WRS0256 WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front seat. An inflating front air bag could seriously injure or kill your child. See “Child restraints” earlier in this section for details. Do not lean against doors or windows.
WARNING LRS0396 Do not lean against doors or windows. SSS0162 Do not lean against doors or windows. 1-52 Safety—Seats, seat belts and supplemental restraint system ● The seat belts, the side air bags and curtain and rollover air bags are most effective when you are sitting well back and upright in the seat. The side air bag and curtain and rollover air bag inflate with great force.
LRS0421 SSS0159 WARNING ● When sitting in the rear seat, do not hold onto the seatback of the front seat. If the side air bag inflates, you may be seriously injured. Be especially careful with children, who should always be properly restrained. Some examples of dangerous riding positions are shown in the illustrations. ● Do not use seat covers on the front seatbacks. They may interfere with side air bag inflation.
1. Roof-mounted curtain side-impact and rollover supplemental air bag 2. Roof-mounted curtain side-impact and rollover supplemental air bags inflators 3. Air bag Control Unit (ACU) 4. Supplemental front-impact air bag modules 5. Crash zone sensor 6. Occupant classification system control unit 7. Occupant classification sensor (pressure sensor) 8. Seat belt buckle switches 9. Seat belt with pretensioner 10. Satellite sensors 11.
The driver supplemental front-impact air bag is located in the center of the steering wheel. The passenger supplemental front-impact air bag is mounted in the dashboard above the glove box. The supplemental front air bags are designed to inflate in higher severity frontal collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact. They may not inflate in certain frontal collisions.
Status light The right front passenger air bag status is located under the climate controls. light After the ignition switch is placed in the ⬙ON⬙ position, the front passenger air bag status light on the instrument panel illuminates for about 7 seconds and then turns off or operates depending on the front passenger seat occupied status. The light operates as follows: is ● Unoccupied passenger’s seat: The OFF and the front passenger air bag is OFF and will not inflate in a crash.
weight on the seat detected by the occupant classification sensor and the belt tension detected on the seat belt, the Advanced Air Bag System determines whether the front passenger air bag should be automatically turned OFF, as required by the regulations. Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the passenger air bag to be automatically turned OFF.
If a malfunction occurs in the front passenger air bag system, the supplemental air bag warning , located in the meter and gauges area light on the driver’s side of the instrument panel, will blink. Have the system checked by a NISSAN dealer. Other supplemental front-impact air bag precautions WARNING ● Do not place any objects on the steering wheel pad or on the instrument panel. Also, do not place any objects between any occupant and the steering wheel or instrument panel.
collisions, although they may inflate if the forces in another type of collision are similar to those of a higher severity side impact. They are designed to inflate on the side where the vehicle is impacted. They may not inflate in certain side collisions. Curtain and rollover air bags are also designed to inflate in certain types of rollover collisions or near rollovers. As a result, certain vehicle movements (for example, during severe off roading) may cause the curtain and rollover air bags to inflate.
WARNING ● Do not place any objects near the seatback of the front seats. Also, do not place any objects (an umbrella, bag, etc.) between the front door finisher and the front seat. Such objects may become dangerous projectiles and cause injury if a side air bag inflates. ● Right after inflation, several side air bag and curtain and rollover air bag system components will be hot. Do not touch them; you may severely burn yourself.
● If you need to dispose of a pretensioner or scrap the vehicle, contact a NISSAN dealer. Incorrect disposal procedures could cause personal injury. The pretensioner system may activate with the supplemental air bag system in certain types of collisions. Working with the seat belt retractor, the pretensioner helps tighten the seat belt when the vehicle becomes involved in certain types of collisions, helping to restrain front seat occupants. The pretensioner is encased with the seat belt retractor.
If any of the following conditions occur, the front air bag, side air bag, curtain and rollover air bag and pretensioner systems need servicing: ● The supplemental air bag warning light remains on after approximately 7 seconds. ● The supplemental air bag warning light flashes intermittently. ● The supplemental air bag warning light does not come on at all.
● The front air bag, side air bag, curtain and rollover air bag systems and the pretensioner system should be inspected by a NISSAN dealer if there is any damage to the front end or side portion of the vehicle. ● If you need to dispose of a supplemental air bag or pretensioners or scrap the vehicle, contact a NISSAN dealer. Correct supplemental air bag and pretensioner system disposal procedures are set forth in the appropriate NISSAN Service Manual.
2 Instruments and controls Instrument panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Meters and gauges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Speedometer and odometer . . . . . . . . . . . . . . . . . . . . . 2-5 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Engine coolant temperature gauge . . . . . . . . . . . . . . . 2-6 Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument panel storage trays . . . . . . . . . . . . . . . . . . 2-42 Console box (if so equipped) . . . . . . . . . . . . . . . . . . . 2-43 Center armrest storage (if so equipped) . . . . . . . . . . 2-44 Glove box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-45 Sunglasses holder (if so equipped) . . . . . . . . . . . . . . 2-45 Map pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-46 Seatback pocket (if so equipped) . . . . . . . . . . . . . . .
INSTRUMENT PANEL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. LIC2437 2-2 Instruments and controls Vents (P. 4-17) Headlight/fog light (if so equipped)/turn signal switch (P. 2-30) Steering wheel switch for audio control/Bluetooth姞 Hands-Free Phone System (if so equipped) (P. 4-71, P. 4-83, P. 4-98, P. 4-109) Instrument brightness control (P. 2-33) Driver supplemental air bag/horn (P. 1-47, P. 2-34) Meters, gauges and warning/indicator lights (P.
15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. Front passenger air bag status light (P. 1-56) Power outlet (P. 2-39) Heated seat switch (if so equipped) (P. 2-34) Vehicle Dynamic Control (VDC) off switch (P. 2-36) Tow mode switch (P. 2-38) Electronic locking rear differential (E-Lock) system switch (if so equipped) (P.2-36) Shift selector (console) (if so equipped) (P. 5-16) Hazard warning flasher switch (P. 6-2) Power outlet (P. 2-39) 4WD shift switch (if so equipped) (P. 5-27) Ignition switch (P.
METERS AND GAUGES WIC1243 1. 2. 3. 4. 5. 6. Warning/indicator lights Tachometer Engine coolant temperature gauge Voltmeter (if so equipped) Fuel gauge Speedometer 2-4 Instruments and controls 7. 8. 9.
WIC1244 1. 2. 3. Speedometer Odometer/twin trip display Change button SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed. Odometer/Twin trip odometer The odometer/twin trip odometer is displayed when the ignition switch is placed in the ON position. The odometer records the total distance the vehicle has been driven. The twin trip odometer records the distance of individual trips.
CAUTION If the gauge indicates coolant temperature near the hot (H) end of the normal range, reduce vehicle speed to decrease temperature. If the gauge is over the normal range, stop the vehicle as soon as safely possible. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” in the “In case of emergency” section for immediate action required. WIC1246 TACHOMETER The tachometer indicates engine speed in revolutions per minute (rpm).
indicates that the fuel-filler door is The located on the driver’s side of the vehicle. CAUTION ● If the vehicle runs out of fuel, the Malfunction Indicator Light (MIL) may come on. Refuel as soon as possible. light After a few driving trips. the should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer. LIC1199 FUEL GAUGE The gauge indicates the approximate fuel level in the tank.
CAUTION ● This gauge is not designed to indicate low engine oil level. Use the dipstick to check the oil level. (See “Engine oil” in the “Maintenance and do-it-yourself” section.) ● If the gauge needle does not move with the proper amount of engine oil, have the vehicle checked by a NISSAN dealer. Continued vehicle operation in such a condition could cause serious damage to the engine.
COMPASS DISPLAY (if so equipped) CAUTION ● This gauge is not designed to indicate low automatic transmission fluid level. Use the dipstick to check the fluid level. (See “5-speed automatic transmission fluid” in the “Maintenance and do-ityourself” section.) ● If the gauge indicates automatic transmission fluid temperature over the normal range, stop the vehicle as soon as safely possible. Have the vehicle checked by a NISSAN dealer. Continued operation of the vehicle may seriously damage the transmission.
WIC0904 Type A COMPASS DISPLAY Push the or button for about 1 second when the ignition switch is placed in the ON position to toggle the compass direction display 1 on or off. The display will indicate the direction 䊊 that the vehicle is heading. N: North E: East S: South W: West 2-10 Instruments and controls LIC1487 Type B If the display reads “C”, calibrate the compass by driving the vehicle in three complete circles at less than 5 MPH (8 km/h).
Zone variation change procedure The difference between magnetic north and geographical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass readings. Follow these instructions to set the variance for your particular location if this happens: button for about 1. Press and hold the button for about 8 11 seconds or the seconds. The current zone number will appear in the display. Release the button. 2. Find your current location on the zone map.
1. With the display turned on, press and hold the button for about 13 seconds or the for about 10 seconds. The “C” icon in the compass display will illuminate. 2. Calibrate the compass by driving the vehicle in three complete circles at a maximum speed of 5 MPH (8 km/h). 3. After completing the circles, the display should return to normal. CAUTION ● Do not install a ski rack, antenna, etc., which are attached to the vehicle by means of a magnet. They affect the operation of the compass.
WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS Low fuel warning light High beam indicator light (Blue) Automatic transmission check warning light Low tire pressure warning light Malfunction indicator light (MIL) Automatic transmission park warning light model) ( Master warning light (if so equipped) Security indicator light (if so equipped) or Seat belt warning light and chime Slip indicator light Charge warning light Supplemental air bag warning light Turn signal/hazard indicator lights Engin
or Anti-lock Braking System (ABS) warning light When the ignition switch is placed in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational. If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock function is turned off.
WARNING ● Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous. ● Pressing the brake pedal with the engine stopped and/or a low brake fluid level may increase your stopping distance and braking will require greater pedal effort as well as pedal travel.
4WD warning light ( model) The 4WD warning light comes on when the key switch is turned to ON. It turns off soon after the engine is started. If the engine or vehicle is not functioning properly, the warning light will either remain illuminated or blink. See “4WD warning light” in the “Starting and driving” section. CAUTION ● If the warning light comes on or blinks during operation, have your vehicle checked by a NISSAN dealer as soon as possible.
TPMS malfunction: If the TPMS is not functioning properly, the low tire pressure warning light will flash for approximately 1 minute when the ignition switch is placed in the ON position. The light will remain on after the 1 minute. Have the system checked by a NISSAN dealer. The CHECK TIRE PRESSURE warning does not appear if the low tire pressure warning light illuminates to indicate a TPMS malfunction.
Master warning light (if so equipped) This light comes on when various vehicle information display warnings appear. ● No key warning ● Low fuel warning ● Low windshield-washer fluid warning ● Parking brake release warning ● Door open warning ● Loose fuel cap warning ● Check tire pressure warning Seat belt warning light and chime The light and chime remind you to fasten your seat belts.
light remains on. If the switch is on and the indicator light continues to flash, the system is not engaged. For additional information, see “Electronic locking rear differential (E-Lock) system switch” later in this section and “Electronic locking rear differential (E-Lock) system” in the “Starting and driving” section of this manual.
CAUTION Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced fuel economy, and possible damage to the emission control system. Security indicator light (if so equipped) This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates the security system equipped on the vehicle is operational. For additional information, see “Security systems” later in this section.
VEHICLE INFORMATION DISPLAY (if so equipped) The icons at the bottom of the display screen show the options available: ENTER — Press the INFO button to select a highlighted option. NEXT — Rotate the INFO button to highlight an option. WIC1248 1 is located to The vehicle information display 䊊 the left of the speedometer.
WIC1166 Warning mode (if so equipped) The warning mode can be selected to view any warnings that may be present. Once the screen is selected you have the option of skipping the warning or viewing it in detail. Warnings can be present for issues such as an open door or low fuel. For more information about potential warnings, see “Vehicle information display warnings and indicators” later in this section.
LIC2006 Vehicle information display warnings and indicators 4. Parking brake warning 5. Cruise main switch indicator (if so equipped) 8. 4WD shift indicator ( 9. Automatic transmission position indicator 1. Door open warning 6. Cruise set switch indicator (if so equipped) 10. Loose fuel cap warning 2. Low fuel warning 7. Transfer 4LO position indicator ( model) 11. Check tire pressure warning 3.
Door open warning This warning illuminates when a door has been opened and the engine is running. Low fuel warning This warning illuminates when the fuel level in the fuel tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches E (Empty). There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E (Empty). Low windshield-washer fluid warning This warning illuminates when the windshieldwasher fluid is at a low level.
SECURITY SYSTEMS (if so equipped) Check tire pressure warning The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your keys in the ignition, and always lock the vehicle when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.
Keyfob operation: ● Push the button on the keyfob. All doors lock. The hazard lights flash twice and the horn beeps once to indicate all doors are locked. button is pushed with ● When the all doors locked, the hazard lights flash twice and the horn beeps once as a reminder that the doors are already locked. The horn may or may not beep.
WINDSHIELD WIPER AND WASHER SWITCH 3. Repeat steps 1 and 2. 4. Restart the engine while holding the device (which may have caused the interference) separate from the registered key. If the no start condition re-occurs, NISSAN recommends placing the registered key on a separate key ring to avoid interference from other devices.
REAR WINDOW AND OUTSIDE MIRROR (if so equipped) DEFROSTER SWITCH NOTE: CAUTION You can turn on or turn off the driving speed dependent intermittent wiper function for vehicles with navigation system. Refer to “Vehicle electronic systems” in the “Display screen, heater, air conditioner, audio and phone systems” section later in this manual. 2 䊊 3 䊊 Low (LO) — continuous low speed operation High (HI) — continuous high speed operation 4 to have one sweep operaPush the lever up 䊊 tion (MIST) of the wiper.
NOTE: If the rear power window (if so equipped) is lowered while the defroster switch is on, the rear window defroster will automatically shut off. The heated outside mirrors (if so equipped) will remain on. The rear window defroster will automatically turn on when the rear power window is fully closed if the switch is on. CAUTION LIC1173 Type B LIC1158 When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defroster.
HEADLIGHT AND TURN SIGNAL SWITCH SIC2745 Type A HEADLIGHT CONTROL SWITCH Lighting 1 䊊 2 䊊 When turning the switch to the position, the front parking, tail, license plate and instrument panel lights come on. When turning the switch to the position, the headlights come on and all the other lights remain on. 2-30 Instruments and controls WIC1250 Type B CAUTION Use the headlights with the engine running to avoid discharging the vehicle battery.
To turn on the autolight system: 1. Turn the headlight switch to the AUTO posi1 . tion 䊊 2. Place the ignition switch in the ON position. 3. The autolight system automatically turns the headlights on and off. Initially, if the ignition switch is placed in the OFF position and a door is opened and left open, the headlights remain ON for a period of time. If another door is opened while the headlights are on, then the timer is reset.
After the headlights automatically turn off with the or position, headlight switch in the the headlights will illuminate again if the headlight switch is moved to the OFF position and then turned to the or position. CAUTION Even though the battery saver feature automatically turns off the headlights after a period of time, you should turn the headlight switch to the OFF position when the engine is not running to avoid discharging the vehicle battery.
WIC1506 WIC1253 WIC1254 INSTRUMENT BRIGHTNESS CONTROL TURN SIGNAL SWITCH FOG LIGHT SWITCH (if so equipped) Turn signal The instrument brightness control operates when the headlight control switch is in , or AUTO position (with autothe lights activated). 1 䊊 To turn the fog lights on, turn the headlight switch to the position, then turn the fog light switch to the position.
HORN CARGO LAMP SWITCH (if so equipped) HEATED SEATS (if so equipped) LIC2051 LIC0616 To sound the horn, push near the horn icon of the steering wheel. To turn on the cargo lamp, push the switch down to the ON position. The tailgate lights (if so equipped) will also illuminate when the cargo lamp switch is in the ON position. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system.
WARNING Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat temperatures or have an inability to feel pain in body parts that contact the seat. Use of the seat heater by such people could result in serious injury. ● If any malfunctions are found or the heated seat does not operate, turn the switch off and have the system checked by your NISSAN dealer. ● The battery could run down if the seat heater is operated while the engine is not running.
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM SWITCH (if so equipped) When the E-Lock switch is turned ON, the indicator light will flash until the system engages. However, if all operation conditions listed above are not met or the system becomes disengaged, the indicator light will continue to flash. The Anti-Lock Brake (ABS) system is disabled and the ABS light illuminates when the E-Lock system is ON.
POWER INVERTER SWITCH (if so equipped) ● Use the E-Lock system only when freeing a stuck vehicle. Try the 4LO position before using the E-Lock system. Never use the E-Lock system on a slippery road surface such as snow or ice surface. Using the E-Lock system when driving in these road conditions may cause unexpected movement of the vehicle during engine braking, accelerating or turning, which may result in an accident and serious personal injury.
REAR SONAR SYSTEM OFF SWITCH (if so equipped) TOW MODE SWITCH The rear sonar system can be disabled by pushing the OFF switch. When the system is disabled, the indicator light on the switch will illuminate. Push the switch again to enable the system. The indicator light will go off. The system will automatically reset the next time the ignition switch is turned on. See “Rear sonar system” in the “Starting and driving” section.
POWER OUTLETS For additional information, refer to “Tow mode” in the “Technical and consumer information” section later in this manual.
CAUTION ● The outlet and plug may be hot during or immediately after use. ● Only certain power outlets are designed for use with a cigarette lighter unit. Do not use any other power outlet for an accessory lighter. See your NISSAN dealer for additional information. ● Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.
LIC0617 In truck box (if so equipped) LIC2433 Center console (if so equipped) Before Drive (idling) (Park) Options When shifting out of Park When shifting back to (idling) (Park) Switch Reset What is plugged IN Indicator Inverter Status Indicator Inverter Status Indicator Inverter Status Indicator Inverter Status Nothing plugged but switch is on 150 and 400 ON 150 ON 150 and 400 ON NOT NECESSARY NOT NECESSARY Device<150W 150 and 400 ON 150 ON 150 and 400 ON NOT NECESSARY NO
STORAGE Do not use the outlet located in the truck box with accessories that exceed 120 volt. Do not use double adapters or more than one electrical accessory. CAUTION ● Operation of the 120 volt system with the ignition in the ON position and the engine not running (idle) will drain the battery charge. This could lead to a dead battery or no start condition. ● Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal temperature fuse may open.
LIC0566 Center tray (if so equipped) LIC1369 LIC1370 CONSOLE BOX (if so equipped) Console box storage Console box storage trays 1 to open the console box lid Pull up on the lever 䊊 2 .
LIC1371 Console box lock 1 or unlock 䊊 2 the Use the master key to lock 䊊 console box. 2-44 Instruments and controls LIC0621 CENTER ARMREST STORAGE (if so equipped) To access the center armrest storage area, lower the center armrest and lift the lid.
CAUTION ● Do not leave sunglasses in the sunglasses holder while parking in direct sunlight. The heat may damage the sunglasses. ● Do not use for anything other than sunglasses. LIC0578 GLOVE BOX Open the glove box by pulling the handle. Use the master key to lock or unlock the glove box lock (if so equipped). The valet key cannot be used. WARNING LIC0567 SUNGLASSES HOLDER (if so equipped) To open the sunglasses holder, push and release.
LIC0589 MAP POCKETS SEATBACK POCKET (if so equipped) The seatback pocket is located on the back of the driver’s seat. The pocket can be used to store maps.
LIC0569 Medium bin (if so equipped) Storage bins LIC1372 Front — Type A LIC0620 Front — Type B CUP HOLDERS WARNING Keep storage bins closed while driving to help prevent injury in an accident or a sudden stop. Push the button to open a storage bin. Push the lid up to close. CAUTION ● Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger. ● Use only soft cups in the cup holder.
LIC1373 Adjustable (if so equipped) Position the arm on the adjustable cup holder so that the cup is held securely. 2-48 Instruments and controls LIC0622 Armrest (if so equipped) LIC0554 2nd row (rear of front console) (if so equipped) To open the 2nd row cup holders (rear of front console), lower the lid. To close, raise the lid.
LIC0556 2nd row bench (if so equipped) LIC0558 Bottle holder — Type A LIC0624 Bottle holder — Type B CAUTION ● Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident. ● Do not use bottle holder for open liquid containers.
CAUTION ● Do not store a total load of more than 22 lbs (10 kg) inside the storage compartment. ● Do not use the storage compartment or storage compartment lid as a step. Doing so may damage them. LIC0626 GROCERY HOOKS (if so equipped) The grocery hooks allow for standard size plastic grocery bags to hang side by side. To access the grocery hooks, fold up the rear bench seat.
WINDOWS POWER WINDOWS (if so equipped) Driver’s side power window switch The driver’s side control panel is equipped with switches to open or close the front and rear passenger windows. WARNING ● Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. ● Do not leave children unattended inside the vehicle.
LIC0580 Front passenger’s power window switch The passenger’s window switch operates only the corresponding passenger’s window. To open 1 . the window, push the switch and hold it down 䊊 2 . To close the window, pull the switch up 䊊 LIC0581 Automatic operation The rear power window switches open or close only the corresponding windows. To open the 1 . To window, push the switch and hold it down 䊊 2 .
Auto-reverse function The auto-reverse function can be activated when a window is closed by automatic operation. Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the window occurs. WARNING There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the window.
MOONROOF (if so equipped) NOTE: If the rear power window (if so equipped) is lowered while the defroster switch is on, the rear window defroster will automatically shut off. The heated outside mirrors (if so equipped) will remain on. The rear window defroster will automatically turn on when the rear power window is fully closed if the switch is on. LIC1553 REAR POWER WINDOW SWITCH (if so equipped) To open the rear power window, push in and hold the switch.
To open or close the moonroof part way, push the 5 while the moonroof is switch in any direction 䊊 sliding open or closed to stop it in the desired position. Tilting the moonroof To tilt the moonroof up, push the tilt switch to1 . ward the up position 䊊 To tilt the moonroof down, push the tilt switch 2 .
INTERIOR LIGHT Sunshade Open and close the sunshade by sliding it forward or backward. If the moonroof does not close Have your NISSAN dealer check and repair the moonroof. LIC0585 Type A The interior light has a three-position switch and operates regardless of ignition switch position. 1 , the When the switch is in the ON position 䊊 interior lights illuminate, regardless of door position. The lights will go off after a period of time unless the ignition switch is placed in the ON position.
PERSONAL LIGHTS (if so equipped) The lights will turn off while the timer is activated when: ● The driver’s door is locked by the keyfob, a key, or the power door lock switch. ● The ignition switch is turned ON. 3 , the When the switch is in the OFF position 䊊 interior lights do not illuminate, regardless of door position. The puddle lights (if so equipped) and cargo light come on when any front or rear passenger door is opened.
MAP LIGHTS (if so equipped) HOMELINK姞 UNIVERSAL TRANSCEIVER (if so equipped) The HomeLink姞 Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink姞 Universal Transceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems. LIC0586 To turn the map lights on, press the switches.
PROGRAMMING HOMELINK姞 If you have any questions or are having difficulty programming your HomeLink姞 buttons, refer to the HomeLink姞 web site at: www.homelink.com or call 1-800-355-3515. NOTE: It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink姞 for quicker programming and accurate transmission of the radiofrequency. 1.
Do not stand on your vehicle to perform the next steps. 4. At the receiver located on the garage door opener motor in the garage, locate the “learn” or “smart” button (the name and color of the button may vary by manufacturer but it is usually located near where the hanging antenna wire is attached to the unit). If there is difficulty locating the button, reference the garage door opener’s manual. 5. Press and release the “learn” or “smart” button. 6.
PROGRAMMING TROUBLEDIAGNOSIS CLEARING THE PROGRAMMED INFORMATION If the HomeLink姞 does not quickly learn the handheld transmitter information: The following procedure clears the programmed information from both buttons. Individual buttons cannot be cleared. However, individual buttons can be reprogrammed, see “Reprogramming a single HomeLink姞 button” in this section. ● replace the hand-held transmitter batteries with new batteries.
FCC Notice: For USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
3 Pre-driving checks and adjustments Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 NISSAN vehicle immobilizer system keys (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Locking with inside lock knob . . . . . . . . . . . . . . . . . . . .
KEYS A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, your NISSAN dealer can duplicate it. NISSAN VEHICLE IMMOBILIZER SYSTEM KEYS (if so equipped) You can only drive your vehicle using the master or valet keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head. WPD0128 1. 2. 3. 4.
DOORS When the doors are locked using one of the following methods, the doors can not be opened using the inside or outside door handles. The doors must be unlocked to open the doors. WARNING ● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders.
Opening and closing windows The driver’s door key operation allows you to open and close windows equipped with automatic operation at the same time. ● To open the windows, turn the driver’s door key toward the rear of the vehicle for longer than 1 second after the door is unlocked. ● To close the windows, turn the driver’s door key toward the front of the vehicle for longer than 1 second after the door is locked. Windows stop when the key cylinder is released.
Lockout protection When the power door lock switch (driver’s or front passenger’s side) is moved to the lock position with the key in the ignition switch and any door open, all doors will lock and then unlock automatically. This helps to prevent the keys from being accidently locked inside the vehicle. LPD0278 LPD0266 WIDE OPEN DOORS (if so equipped) 1 2. From the outside, pull the door handle 䊊 toward you.
LPD0267 From the inside, pull the inside door handle toward you. The door will unlock automatically. LPD0265 3. Open the door to the desired position. AUTOMATIC DOOR LOCKS (if so equipped) ● All doors lock automatically when the vehicle speed reaches 15 MPH (24 km/h). ● All doors unlock automatically when the transmission is placed in the P (Park) position. The automatic unlock function can be deactivated or activated.
REMOTE KEYLESS ENTRY SYSTEM (if so equipped) 5. The ignition switch must be placed in the OFF and ON position again between each setting change. WARNING ● Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use. When the automatic door unlock system is deactivated, the doors do not unlock when the transmission is placed in the P (Park) position.
Be sure to remove the key from the vehicle before locking the doors. ● Do not strike the keyfob sharply against another object. The keyfob can operate at a maximum distance of approximately 33 ft (10 m) from the vehicle. The effective distance depends upon the conditions around the vehicle. ● Do not change or modify the keyfob. As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer.
● When the button is pressed with all doors locked, the hazard warning lights flash twice and the horn beeps once as a reminder that the doors are already locked. button on the keyfob again Press the within 5 seconds. ● All doors unlock. ● The hazard warning lights flash once if all doors are completely closed. ● If a door is open and you press the button, the doors will lock but the horn will not beep and the hazard warning lights will not flash. The horn may or may not beep.
Using the interior lights Press the button on the keyfob once to turn on the interior lights and puddle lights (if so equipped). For additional information, refer to “Interior light” in the “Instruments and controls” section in this manual. LPD0211 LPD0262 Using the panic alarm Silencing the horn beep feature If you are near your vehicle and feel threatened, you may activate the panic alarm to call attention button on the by pressing and holding the keyfob for longer than 0.5 seconds.
HOOD To deactivate: Press and hold the and buttons for at least 2 seconds. The hazard warning lights will flash 3 times to confirm that the horn beep feature has been deactivated. To activate: Press and hold the and buttons for at least 2 seconds once more. The hazard warning lights will flash once and the horn will sound once to confirm that the horn beep feature has been reactivated. Deactivating the horn beep feature does not silence the horn if the alarm is triggered.
FUEL-FILLER DOOR ● Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire. LPD0263 FUEL-FILLER CAP WARNING ● Gasoline is extremely flammable and highly explosive under certain conditions. You could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling.
● Failure to tighten the fuel-filler cap properly may cause the Malfunction Indicator Light (MIL) to illuminate. light illuminates because If the the fuel-filler cap is loose or missing, tighten or install the cap and continue light to drive the vehicle. The should turn off after a few driving trips. light does not turn off after a If the few driving trips, have the vehicle inspected by a NISSAN dealer.
STEERING WHEEL PEDAL POSITION ADJUSTMENT (if so equipped) CAUTION Do not adjust the pedal position with your foot on the pedal. LPD0254 TILT OPERATION WARNING Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident. Pull the lock lever forward and hold it to adjust the steering wheel up or down to the desired position. Release the lock lever to lock the steering wheel in place.
SUN VISORS 1 䊊 2 䊊 3 䊊 To block glare from the front, swing down the main sun visor. To block glare from the side, remove the main sun visor from the center mount and swing the visor to the side. To extend the sun visor, slide in or out as needed. CAUTION ● Do not store the sun visor before returning the extension to its original position. ● Do not pull the extension sun visor forcedly downward.
MIRRORS AUTOMATIC ANTI-GLARE REARVIEW MIRROR (if so equipped) The inside mirror is designed so that it automatically dims during night time conditions and according to the intensity of the headlights of the vehicle following you. The automatic anti-glare feature is activated when the ignition switch is in the ON position. The indicator light will illuminate when the automatic anti-glare feature is operating.
For more information about the compass and 2 (if so equipped), see compass features 䊊 “Compass display” in the “Instruments and controls” section of this manual. LPD0446 LPD0447 Type A Type B Type A Type B With the ignition switch placed in the ON posibutton as described: tion, press the With the ignition switch in the ON position, press button as described: the ● To turn off the anti-glare feature, press button. The indicator light will turn the off.
For information on HomeLink姞 Universal Transceiver operation, see “HomeLink姞 Universal Transceiver” in the “Instruments and controls” section of this manual. For information on the compass and compass 2 , see “Compass display” in the “Infeatures 䊊 struments and controls” section of this manual. OUTSIDE MIRRORS WARNING ● Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident.
Use the outside mirror remote control to adjust the top portion of the trailer tow mirror. The lower portion of the trailer tow mirror can be moved manually in any direction for a better rear view. LPD0279 Trailer tow mirrors (if so equipped) WARNING Objects viewed in the convex portion of the trailer tow mirror are closer than they appear. Be careful when changing lanes or turning. Using only the convex mirror could cause an accident.
LPD0259 Type A Manual folding outside mirrors (if so equipped) Pull the outside mirror toward the door to fold it. LPD0269 Type B LPD0196 Power folding outside mirrors (if so equipped) CAUTION Do not manually fold the power folding mirrors. Manually folding the mirrors can damage the mirrors. Push the switch to open or close the mirrors. If one of the mirrors are manually operated or bumped, the mirror body can become loose at the pivot point.
TRUCK BOX For proper truck box loading see “Vehicle loading information” in the “Technical and consumer information” section of this manual. Automatic anti-glare outside mirror (Driver’s side only) (if so equipped) The outside mirror will automatically dim during nighttime conditions to reduce the glare from the headlights of trailing vehicles. The automatic antiglare feature operates only when the ignition switch is placed in the ON position.
6. Take the tailgate plug from the glove box and connect it to the tailgate wiring harness to avoid contamination which will lead to malfunction of the rear camera. 7. Remove the tailgate. See “Removing the tailgate” in this section. LPD2097 Disconnecting the rear camera (if so equipped) Before removing the tailgate disconnect the rear camera by performing the following: 1. Open the tailgate to access the rear camera 1 located on the rear connector bracket 䊊 sill. 2 from the 2.
3. Hold the tailgate at a 45 degree angle. 4. Pull the tailgate out from the left side hinge. 5. Slide the tailgate out of the right side hinge. Installing the tailgate 1. Insert the tailgate into the right side hinge. 2. Hold the tailgate at a 45 degree angle and insert into the left side hinge. 3. Continue to hold the tailgate at a 45 degree angle and attach the tailgate support cables. LPD0271 Removing the tailgate 1. Disconnect the wiring harness for the rear camera (if so equipped).
LPD2097 Connecting the rear camera (if so equipped) Before closing the tailgate reconnect the rear camera by performing the following: : 1. After attaching the rear tailgate to the truck, keep the tailgate open and check that the tailgate harness is not hanging below the tailgate. 2 from the 2. Remove the connector bracket 䊊 sill by pressing the locking tab inward, in the direction shown, while pulling the bracket apart. 3-24 Pre-driving checks and adjustments 3.
AUTOMATIC DRIVE POSITIONER (if so equipped) WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury. The automatic drive positioner system has two features: ● Memory storage function ● Entry/exit function LTI0102 TIE DOWN HOOKS For your convenience, tie down hooks are placed at each corner of the truck box. These may be used to help secure cargo loaded into the truck box.
mation, see “Seats” in the “Safety—Seats, seat belts and supplemental restraint system” section of this manual and “Pedal position adjustment” and “Outside mirrors” earlier in this section. During this step, do not place the ignition switch in any position other than ON. 4. Push the SET switch and, within 5 seconds, push the memory switch (1 or 2).
● If the battery cable is disconnected, or if the fuse opens, the memory storage function will be canceled and must be restarted before a stored memory position can be set again. Drive the vehicle over 25 MPH (40 km/h) to restart the memory storage function. You can also restart the memory storage function using the following procedure. 1. Connect the battery cable or replace the fuse. 2. Open and close the driver’s door more than 2 times with the ignition switch in the LOCK position.
SYSTEM OPERATION The automatic drive positioner system will not work or will stop operating under the following conditions: ● When the vehicle speed is above 4 MPH (7 km/h). ● When any of the memory switches are pushed while the automatic drive positioner is operating. ● When the adjusting switch for the driver’s seat is turned on while the automatic drive positioner is operating. ● When the seat has already been moved to the memorized position. ● When no seat position is stored in the memory switch.
4 Monitor, climate, audio, phone and voice recognition systems Control panel buttons — color screen with Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . 4-4 How to use the touch screen . . . . . . . . . . . . . . . . . . . . 4-5 How to use the BACK button . . . . . . . . . . . . . . . . . . . . 4-7 How to use the MENU button . . . . . . . . . . . . . . . . . . . . 4-7 button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 RearView Monitor (if so equipped). . .
USB interface (models without Navigation System) (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . 4-59 USB interface (models with Navigation System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60 iPod姞* player operation without Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . 4-62 iPod姞* player operation with Navigation System (if so equipped) . . . . . . . . . . . . . . . . . . . . . . . .
Ending a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-105 Text messaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-105 Bluetooth姞 settings . . . . . . . . . . . . . . . . . . . . . . . . . . .4-107 Manual control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-109 Bluetooth姞 Hands-Free Phone System with Navigation System (if so equipped) . . . . . . . . . . . . . . . .4-109 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . .
CONTROL PANEL BUTTONS — COLOR SCREEN WITH NAVIGATION SYSTEM (if so equipped) WARNING ● Positioning of the heating or air conditioning controls and display controls should not be done while driving in order that full attention may be given to the driving operation. ● Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound.
9. Power button/VOL (volume) control knob 10. CAMERA button * For information regarding the Navigation system control buttons, refer to the separate Navigation System Owner’s Manual. ** For information regarding the Bluetooth姞 Hands-Free Phone System control button, see “Bluetooth姞 Hands-Free Phone System” in this section. When you use this system, make sure the engine is running.
LHA2246 LHA1478 Touch screen operation LHA2245 Adjusting the item: Selecting the item: For screens where an item can be adjusted incrementally, such as when adjusting the bass and 1 treble for the audio system, touch the “+” key 䊊 2 to adjust the settings of an item. or the “⫺” key 䊊 Other items are adjusted by selecting one of a set number of conditions. For example, the Display Mode can be set to “Automatic”, “Day” or “Night”. 1 .
● OK: Completes the character input. Touch screen maintenance If you clean the display screen, use a dry, soft cloth. If additional cleaning is necessary, use a small amount of neutral detergent with a soft cloth. Never spray the screen with water or detergent. Dampen the cloth first and then wipe the screen. HOW TO USE THE BACK BUTTON LHA2247 Inputting characters: 1 . Touch the letter key 䊊 There are some options available when inputting characters.
For information regarding Bluetooth姞 audio, see “Bluetooth姞 streaming audio with Navigation System” in this section. LHA2248 3. Select the desired item. Audio For audio setup, refer to “Audio system” in this section. Navigation Refer to the separate Navigation System Owner’s Manual for information regarding this item. Phone & Bluetooth For information regarding the Bluetooth姞 HandsFree Phone System, see “Bluetooth姞 HandsFree Phone System” in this section.
“Night” modes are suited for the respective times of day, while “Automatic” controls the display automatically. Scroll Direction The direction that menus scroll can be adjusted. Choose either “up” or “down”. LHA1482 LHA2250 Display: Clock Settings: Select the “Display” key to adjust the appearance of the display. The following settings can be adjusted: Select the “Clock Settings” key to adjust the time and the appearance of the clock on the display.
Clock Mode Select the mode for the clock. “Auto” uses the system’s GPS to automatically maintain the time. “Manual” allows you to set the clock using the “Set Clock Manually” key. “Time Zone” maintains the time based upon the zone selected when selecting the “Time Zone” key. LHA2251 LHA2252 Set Clock Manually When this setting is activated, the clock can be set manually. Touch the “+” or “-” keys to adjust the hours, minutes, day, month and year up or down.
REARVIEW MONITOR (if so equipped) System Beeps: Select the “System Beeps” key to toggle the system beep tones feature on or off. When activated, a beep sound will be heard when a pop-up message appears on the screen or a button on button) is pressed the unit (such as the and held for two seconds. Reset all settings/memory: Select the “Reset All Settings/Memory” key to return all settings to default and to clear the memory.
DIFFERENCE BETWEEN PREDICTED AND ACTUAL DISTANCES The distance guide line and the vehicle width guide line should be used as a reference only when the vehicle is on a level, paved surface. The distance viewed on the monitor is for reference only and may be different than the actual distance between the vehicle and displayed objects. LHA0437 HOW TO READ THE DISPLAYED LINES Guiding lines which indicate the vehicle width and distances to objects with reference to the A are displayed on the monitor.
B . Note that any object on the hill is the place 䊊 the hill is further than it appears on the monitor. LHA2326 LHA2327 Backing up on a steep uphill Backing up on a steep downhill When backing up the vehicle up a hill, the distance guide lines and the vehicle width guide lines are shown closer than the actual distance. For example, the display shows 3 ft (1.0 m) to the A , but the actual 3 ft (1.
B . Note that any object on the hill is the place 䊊 the hill is closer than it appears on the monitor. A if the object projects over the the position 䊊 actual backing up course. LHA2328 Backing up behind a projecting object C is shown farther than the position The position 䊊 B in the display. However, the position 䊊 C is 䊊 A.
4. Adjust the level using the TUNE-SCROLL knob and then press the ENTER/SETTING button to apply the adjustment. ● Do not adjust the Brightness or Contrast of the RearView Monitor while the vehicle is moving. LHA2254 Without Navigation System ADJUSTING THE SCREEN The procedure for adjusting the quality of the screen differs depending on the type of screen present on the vehicle. For vehicles without Navigation System: 1. Press the ENTER/SETTING button. 2.
OPERATING TIPS CAUTION ● Do not use alcohol, benzine or thinner to clean the camera. This will cause discoloration. To clean the camera, wipe with a cloth dampened with a diluted mild cleaning agent and then wipe with a dry cloth. ● Do not damage the camera as the monitor screen may be adversely affected. ● When the shift selector is shifted to R (Reverse), the monitor screen automatically changes to the RearView Monitor mode. However, the radio can be heard.
VENTS HEATER AND AIR CONDITIONER (manual) (Type A) (if so equipped) WARNING ● The air conditioner cooling function operates only when the engine is running. WHA1128 Adjust air flow direction for the driver’s and pas1 , center vents 䊊 2 , and rear senger’s side vents 䊊 3 by moving passengers’ (if so equipped) vents 䊊 the vent slide and/or vent assemblies. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone.
— Air flows from center and side vents. — Air flows from center and side vents and the front and rear floor outlets. — Air flows mainly from the front and rear floor outlets. — Air flows from defroster outlets and the front and rear floor outlets. Temperature control dial WHA1406 Type A 1. 2. 3. 4. 5. 6. 7. 8.
The air recirculation mode is only functional when the air flow control mode is in the following positions: or . OFF position: button again to turn air recirculaPush the tion off. Outside air is drawn into the passenger compartment and distributed through the selected outlet. Use the off position for normal heater or air conditioner operation. Air conditioner button Start the engine, turn the fan control dial to the button to desired position and push the turn on the air conditioner.
Bi-level heating The bi-level mode directs warmed air to the side and center vents and to the front and rear floor outlets. button to the OFF position. 1. Press the button will The indicator light on the go off. 2. Press the air flow control button. 3. Turn the fan control dial to the desired position. 4. Turn the temperature control dial to the desired position. Heating and defogging This mode heats the interior and defogs the windshield. 1. Press the air flow control button. 2.
Dehumidified heating This mode is used to heat and dehumidify the air. 1. Press the button to the OFF position. The indicator light on the button will go off. 2. Press the air flow control button. 3. Turn the fan control dial to the desired position. 4. Press the light on the button on. The indicator button will come on. 5. Turn the temperature control dial to the desired position. Operating tips ● Keep the windows closed while the air conditioner is in operation.
WHA0916 Type A 4-22 Monitor, climate, audio, phone and voice recognition systems WHA0917 Type A
WHA0918 Type A WHA0919 Type A Monitor, climate, audio, phone and voice recognition systems 4-23
WHA1362 Type A 4-24 Monitor, climate, audio, phone and voice recognition systems
HEATER AND AIR CONDITIONER (manual) (Type B) (if so equipped) WARNING ● The air conditioner cooling function operates only when the engine is running. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
— Air flows mainly from the front and rear floor outlets. — Air flows from defroster outlets and the front and rear floor outlets. — Air flows mainly from defroster outlets. The air flow control dial also has intermediate positions which allow the air flow to be distributed between 2 of the icon positions on the air flow control dial. Temperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. To lower the temperature, turn the dial to the left.
2. Turn the air flow control dial to the position. 3. Turn the fan control dial to the desired position. 4. Turn the temperature control dial to the desired position. Defrosting or defogging This mode directs the air to the defrost outlets to defrost/defog the windows. 1. Turn the air flow control dial to the position. 2. Turn the fan control dial to the desired position. 3. Turn the temperature control dial to the desired position between the middle and the hot position.
Operating tips Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater operation. AIR CONDITIONER OPERATION Start the engine, turn the fan control dial to the desired position, and push in the button to activate the air conditioner. When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function operates only when the engine is running.
AIR FLOW CHARTS The following charts show the button and dial positions for MAXIMUM AND QUICK heating, cooling or defrosting. For additional information on heating and cooling see “Heater and air conditioner” in this section. The air recirculation ) button should always be in the OFF ( position for heating and defrosting.
WHA1080 4-30 Monitor, climate, audio, phone and voice recognition systems WHA1081
WHA1082 WHA1471 Monitor, climate, audio, phone and voice recognition systems 4-31
HEATER AND AIR CONDITIONER (automatic) (if so equipped) ● Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up. Start the engine and operate the controls to activate the air conditioner. AUTOMATIC OPERATION Cooling or heating (auto) LHA2468 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
● The temperature of the passenger compartment will be maintained automatically. Air flow distribution, fan speed and A/C on/off are also controlled automatically. ● A visible mist may be seen coming from the vents in hot, humid conditions as the air is cooled rapidly. This does not indicate a malfunction. Dehumidified defrosting or defogging 1. Press the defroster control button to turn the system on. The indicator light in the button will illuminate. 2.
SERVICING AIR CONDITIONER AUDIO SYSTEM The air conditioner system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. RADIO This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system.
Reception conditions will constantly change because of vehicle movement. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception. Static and flutter: During signal interference from buildings, large hills or due to antenna position (usually in conjunction with increased distance from the station transmitter), static or flutter can be heard.
Compact disc (CD) player CAUTION ● Do not force a compact disc into the CD insert slot. This could damage the CD and/or CD player. ● Trying to load a CD with the CD door closed could damage the CD and/or CD player. ● Only one CD can be loaded into the CD player at a time. ● Only use high quality 4.7 in (12 cm) round discs that have the “COMPACT disc DIGITAL AUDIO” logo on the disc or packaging. ● During cold weather or rainy days, the player may malfunction due to the humidity.
CHECK DISC: ● Confirm that the CD is inserted correctly (the label side is facing up, etc.). ● Confirm that the CD is not bent or warped and it is free of scratches. PRESS EJECT: This is an error due to excessive temperature inside the player. Remove the CD by pressing the EJECT button. After a short time, reinsert the CD. The CD can be played when the temperature of the player returns to normal. UNPLAYABLE: The file is unplayable in this audio system (only MP3 or WMA (if so equipped) CD).
Playback order: Music playback order of a CD with MP3 or WMA files is as illustrated. ● The names of folders not containing MP3 or WMA files are not shown in the display. ● If there is a file in the top level of the disc, “Root Folder” is displayed. ● The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired order.
Specification chart: Supported media Supported file systems MP3 Supported versions*1 WMA Version Sampling frequency Bit rate Version Sampling frequency Bit rate Tag information Folder levels Text character number limitation Displayable character codes*2 CD, CD-R, CD-RW ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. MPEG1, MPEG2, MPEG2.
Troubleshooting guide: Symptom Cannot play Poor sound quality It takes a relatively long time before the music starts playing. Music cuts off or skips Skipping with high bit rate files Moves immediately to the next song when playing Songs do not play back in the desired order Cause and Countermeasure Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player.
Universal Serial Bus (USB) memory (if so equipped) ● The USB device cannot be formatted with this system. If you want to format the USB memory, use your personal computer. This system supports various USB memory sticks, USB hard drives and iPod姞 players. There are some USB devices which may not be supported with this system. ● Partitioned USB devices may not be played correctly. ● Make sure that the USB device is connected correctly into the USB connector.
● Operating procedure of the Bluetooth姞 audio will vary depending on the devices. Make sure how to operate your audio device before using it with this system. ● The Bluetooth姞 audio may be stopped under the following conditions: BLUETOOTH威 is a trademark owned by Bluetooth SIG, Inc. and licensed to Visteon and Bosch. ● Receiving a call on the Hands-Free Phone System. ● Checking the connection to the handsfree phone.
FM/AM RADIO WITH COMPACT DISC (CD) PLAYER (if so equipped) For all operation precautions, see ⬙Audio operation precautions⬙ earlier in this section. Audio main operation Power button and VOL control knob Place the ignition switch in the ACC or ON position, then press the PWR (power) button. If you listen to the radio with the engine not running, place the ignition switch in the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing.
To adjust Bass, Treble, Fade and Balance, press the MENU button until the desired mode appears in the display. Press the SEEK button to adjust Bass and Treble to the desired level. You can also use the SEEK button to adjust Fade and Balance modes. Fade adjusts the sound level between the front and rear speakers and Balance adjusts the sound between the right and left speakers.
1. Press the PRESET A·B·C button to change between storage banks. The radio displays the icon A, B or C to indicate which set of presets are active. TUNE buttons: Manual tuning or button for less Press the TUNE than 0.5 seconds for manual tuning. To move quickly through the channels, press and or hold either TUNE for more than 1.5 seconds. button down SEEK buttons: SEEK tuning or button to seek Press the SEEK through the frequencies.
SEEK (Scan CDs) button: Press and hold the SEEK button for more than 1.5 seconds to scan through the first 10 seconds of a track on the compact disc. The SCAN icon is flashed during scan mode. CD EJECT button: button is pressed with a comWhen the pact disc loaded, the compact disc will be ejected. The scan mode is canceled once it scans through all the tracks on the disc, or if the SEEK or button is pressed during the scan mode.
12.Station select (1 - 6) buttons 13.RDM button 14.RPT button 15.DISP button 16.VOL (volume) knob / PWR (power) button 17.CD•AUX button 18.FM•AM button *No satellite radio reception is available when the XM button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and an SiriusXM Satellite Radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam. LHA2501 1. 2. 3. 4. 5. 6.
FM/AM/SAT RADIO WITH COMPACT DISC (CD) PLAYER (Type A) (if so equipped) For all operation precautions, see “Audio operation precautions” in this section. Audio main operation VOL (volume) knob / ON-OFF button: Place the ignition switch in the ACC or ON position and press the VOL (volume) knob / ON-OFF button while the system is off to call up the mode that was playing immediately before the system was turned off. To turn the system off, press the VOL (volume) knob / ON-OFF button.
Brightness and Contrast iPod姞 MENU button Adjust the brightness or contrast to adjust the appearance of the display screen. This button can only be used for iPod姞 operations. See “iPod姞 player operation without Navigation System” later in this section for details about the function of this button. Clock Adjust Press the ENTER button to highlight the hours or minutes and then use the TUNE/SCROLL knob to adjust the value. Press the ENTER button again to set the value.
When the XM button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. The last station played will also come on when the VOL/ON·OFF control knob is pressed ON. *When the XM button is pressed, the satellite radio reception will not be available unless an optional satellite receiver and antenna are installed and a SiriusXM Satellite Radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam.
SEEK/CAT button: Press the SEEK/CAT button while a CD or MP3/WMA CD is playing to return to the beginning of the current track. Press the SEEK/CAT several times to skip backward sevbutton eral tracks. while a CD or Press the SEEK/CAT button MP3/WMA CD is playing to advance one track. several times Press the SEEK/CAT button to skip forward several tracks. If the last track on a CD is skipped, the first track on the disc is played.
When the button is pressed twice with a compact disc loaded, the compact disc will be ejected further for easier CD removal. If the disc is not removed within 20 seconds, the disc will reload. Additional features For more information about the iPod姞 player available with this system, see “iPod姞 player operation without Navigation System” in this section. For more information about the USB interface available with this system, see “USB interface (models without Navigation System)” in this section.
10.CD button 11.XM button* *No satellite radio reception is available when the XM button is pressed to access satellite radio stations unless optional satellite receiver and antenna are installed and an SiriusXM Satellite Radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam. To turn the system off, press the ON-OFF button. Turn the VOL (volume) control knob to adjust the volume. This vehicle may be equipped with Speed Sensitive Volume.
FM/AM/SAT radio operation FM·AM button: Press the FM·AM button to change the band as follows: AM → FM1 → FM2 → AM If another audio source is playing when the FM·AM button is pressed, the audio source playing will automatically be turned off and the last radio station played will begin playing. LHA2262 Speed Sensitive Vol.: Controls the level to which the volume is adjusted as the vehicle’s driving speed changes. Choose a setting or choose “0” to disable the feature entirely.
*When the XM button is pressed, the satellite radio mode will be skipped unless an optional satellite receiver and antenna are installed and a SiriusXM Satellite Radio service subscription is active. Satellite radio is not available in Alaska, Hawaii and Guam. If a compact disc is playing when the XM button is pressed, the compact disc will automatically be turned off and the last radio station played will come on.
Tuning with the TUNE knob: 3. The channel indicator will then come on and the sound will resume. Programming is now complete. The radio can also be manually tuned using the TUNE knob. When in FM or AM mode, turn the TUNE knob to the left for lower frequencies or to the right for higher frequencies. When in XM mode, turn the TUNE knob to change the channel. 4. Other buttons can be set in the same manner. If the battery cable is disconnected or if the fuse opens, the radio memory will be canceled.
LHA1488 CD/MP3 display mode While listening to a CD or an MP3/WMA CD, certain text may be displayed (when a CD encoded with text is being used). Depending on how the CD or MP3/WMA CD is encoded, the text is displayed listing the artist, album and song title. There are other keys displayed on the screen when a CD is playing: LHA1490 LHA1491 Random: Touch the “Random” key to apply a random play pattern to the CD. When the random mode is icon will be displayed to the left active, the of the song title.
playing, touching the “Browse” key will also list the folders on the disc. Follow the procedure for selecting a song with the touchscreen to choose a folder. SEEK (Reverse or Fast Forward) buttons: or Press and hold the seek buttons for 1.5 seconds while the compact disc is playing to reverse or fast forward the track being played. The compact disc plays at an increased speed while reversing or fast forwarding. When the button is released, the compact disc returns to normal play speed.
Additional features Audio file operation For more information about the iPod姞 player available with this system, see “iPod姞 player operation with Navigation System” in this section. CD•AUX button: Place the ignition switch in the ON or ACC position and press the CD•AUX button to switch to the USB input mode. If a CD is playing or another audio source is plugged in through the AUX IN jack on the radio, the CD•AUX button toggles between the three sources.
SEEK/CAT buttons: Press the SEEK/CAT button while an audio file on the USB device is playing to return to the beginning of the current track. Press the several times to skip SEEK/CAT button backward several tracks. The current play pattern of the USB device is displayed on the screen unless no pattern is applied.
Audio file operation Press the button while an audio file on the USB device is playing to advance one track. button several times to skip forPress the ward several tracks. If the last track in a folder on the USB device is skipped, the first track of the next folder is played. AUX button: Place the ignition switch in the ON or ACC position and press the AUX button to switch to the USB input mode.
While connected to the vehicle, the iPod姞 can only be operated by the vehicle audio controls. ● iPod姞 Nano - 5th generation (8GB) (firmware version 1.0.2PC or later) To disconnect the iPod姞 from the vehicle, remove the USB end of the cable from the USB jack on the vehicle, then remove the cable from the iPod姞. ● iPod姞 Nano - 5th generation (16GB) (firmware version 1.0.1PC or later) * iPod姞 is a trademark of Apple Inc., registered in the U.S. and other countries.
Audio main operation: ● Songs Place the ignition switch to the ACC or ON position. Then, press the CD·AUX or iPod姞 MENU button repeatedly to switch to the iPod姞 mode. ● Podcasts If the audio system is turned off while the iPod姞 is playing, the iPod姞 plays when the audio system is turned back on. If the audio system is off, pressing the CD·AUX or iPod姞 MENU button turns the audio system on and plays the iPod姞.
While connected to the vehicle, the iPod姞 can only be operated by the vehicle audio controls. ● iPod姞 Nano - 5th generation (firmware version 1.0.1 or later) To disconnect the iPod姞 from the vehicle, remove the USB end of the cable from the USB jack on the vehicle, then remove the cable from the iPod姞. * Some features of this iPod姞 may not be fully functional. * iPod姞 is a trademark of Apple Inc., registered in the U.S. and other countries.
● Playlists ● Artists ● Albums ● Genres ● Songs ● Composers ● Audiobooks ● Podcasts Random and repeat play mode: LHA1494 LHA1495 Audio main operation Interface: Place the ignition switch in the ACC or ON position. Press the AUX button repeatedly to switch to the iPod姞 mode. If the system has been turned off while the iPod姞 was playing, pressing the VOL/ON·OFF control knob will start the iPod姞.
Repeat: Touch the “Repeat” key to apply a repeat play pattern to the iPod姞. When the repeat mode is icon is displayed to the left of active, the the song title or album name to denote which repeat pattern is applied. To cancel Repeat icon mode, touch the “Repeat” key until no is displayed.
LHA2257 LHA2274 To connect your Bluetooth姞 audio device to the vehicle, follow the procedure below: 3. Select the “Add Telephone or Device” key. This same screen can be accessed to remove, replace or select a different Bluetooth姞 device. Connecting Bluetooth姞 audio 1. Press the SETTING button. 2. Select the “Bluetooth” key. 4. The system acknowledges the command and asks you to initiate connecting from the phone handset.
BLUETOOTH姞 STREAMING AUDIO WITH NAVIGATION SYSTEM (if so equipped) If you have a compatible Bluetooth姞 audio device that is capable of playing audio files, the device can be connected to the vehicle’s audio system so that the audio files on the device play through the vehicle’s speakers. LHA2253 Connecting Bluetooth姞 audio To connect your Bluetooth姞 audio device to the vehicle, follow the procedure below: 1. Press the MENU button. 2. Select the “Settings” key.
The controls for the Bluetooth姞 audio are displayed on the screen. PANDORA姞 AUDIO (United States only) (if so equipped) The vehicle’s audio system is capable of playing audio streaming through a compatible, USBconnected audio device using the Pandora姞 music service. Connecting a device for use with Pandora姞 audio LHA2265 4. Select the “Connect New Device” key. 5. The system acknowledges the command and asks you to initiate connecting from the phone handset.
The controls for the Pandora姞 audio are displayed on the screen. Touch the keys on the screen to play or pause the audio. Touch the key key to select to select “thumbs up” or the “thumbs down”. NOTE: There is a limit of six skips per station per ” (thumbs down) is given hour. If a “ after the skip limit has been reached, the current track will continue to play but the feedback will be saved.
● A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated. LHA0049 CD CARE AND CLEANING ● Handle a CD by its edges. Do not bend the disc. Never touch the surface of the disc. ● Always place the discs in the storage case when they are not being used. ● To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion.
SOURCE select switch AM and FM: Bluetooth姞 Audio (if so equipped): Push the source select switch to change the mode in the following sequence: ● Tilt up/down for less than 1.5 seconds to increase or decrease the preset station. ● Tilt up/down for less than 1.5 seconds to skip ahead or back to the next song.
NISSAN MOBILE ENTERTAINMENT SYSTEM (MES) (if so equipped) CAUTION CAUTION ● The glass screen on the liquid crystal display may break if hit with a hard or sharp object. If the glass breaks, do not touch the liquid crystalline material, which contains a small amount of mercury. In case of contact with skin, wash immediately with soap and water. Always properly tighten the antenna rod during installation or the antenna rod may break during vehicle operation.
LHA0316 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. EJECT button DVD slot ENTER button POWER on/off button MODE button Input jacks STOP button PLAY/PAUSE button MENU button DISPLAY button NAVIGATION keys DIGITAL VIDEO DISC (DVD) PLAYER CONTROLS Refer to “Playing a digital video disc (DVD)” in this section for the function of each button. LHA0317 1. 2. 3. 4. 5.
6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. DISPLAY button MODE button SUBTITLE button AUDIO button ANGLE button CLEAR button PAUSE button PLAY button FAST FORWARD/FAST RE VERSE button MENU button NAVIGATION keys BACK button Numeric keypad REMOTE CONTROL Refer to “Playing a digital video disc (DVD)” in this section for the function of each button. CAUTION ● The glass screen on the liquid crystal display may break if hit with a hard or sharp object. If the glass screen breaks, do not touch it.
PLAYING A DIGITAL VIDEO DISC (DVD) CAUTION ● Only operate the DVD while the vehicle engine is running. Operating the DVD for extended periods of time with the engine OFF can discharge the vehicle battery. SAA0720 SAA0721 Headphones NOTE: Power ON/OFF: For optimum infrared headphone performance, increase the volume on the rear seat controller to the maximum level and adjust the infrared headphone volume using the volume control on the headphones.
It is possible to operate the DVD player by remote control. Headphones are a wireless type and no cables are necessary. You can use them in almost all the ranges in the rear seat. (It is not possible to use the headphones in the front seat.) The display will show the “AUX” in the upper left corner of the display for 4 seconds once the Mode is changed to AUX. or PLAY: With the ignition switch placed in the ACC or ON position, press the POWER button to turn the DVD player on or off.
STOP: Press the STOP button once to stop playing the in the upper media. The display will show left corner of the display for 4 seconds, and the last disc position will be stored. When the PLAY button is pressed again, it will resume at the stored disc track and time position. If the STOP button is pressed again when the player is already in Stop mode, it will reinitialize the pointer to the beginning of the disc.
MENU: If the media is in PLAY mode and the MENU button is pressed, the DVD menu will appear on the screen. Use the Navigation Keys to navigate within the menu and use ENTER to select the item. Press the MENU button again to return to PLAY mode. TITLE (Remote control only): Repeatedly press the AUDIO button to cycle through each available audio track.
CARE AND MAINTENANCE ● A new disc may be rough on its inner and outer edges. Remove the rough edges using the side of a pen or pencil as illustrated. Use a lightly dampened, lint free cloth to clean the surfaces of your NISSAN Mobile Entertainment System (DVD player face, screen, remote control, etc.). Do not attempt to use the system in extreme temperature conditions [below -4°F (-20°C) or above 158°F (70°C)]. ● Never attempt to use a DVD that has been cracked, deformed, or repaired using adhesive.
● DVDs with a region code other than A is displayed in “1”. The region code 䊊 a small symbol printed on the top of B. the DVD 䊊 4. Check to see if the jammed DVD has been ejected. If it has not, try to eject the DVD by pushing the eject button. ● DVDs that are not round. 5. If the disc cannot be ejected see your NISSAN dealer for further assistance. ● DVDs with a paper label. 6. Re-program the radio presets. ● DVDs that are warped, scratched, or have unequal edges. ● Recordable (DVD+R).
● When changing batteries, do not let dust or oil get on the remote control and headphones. FCC Notice: LHA0318 Remote control and headphones battery replacement Replace the battery as follows: 1. Open the lid. 2. Replace batteries with new ones. ● Size AA (remote control) ● Size AAA (headphones) and ends on Make sure that the the batteries match the markings inside the compartment. 3. Close the lid securely.
CAR PHONE OR CB RADIO When installing a CB, ham radio or car phone in your vehicle, be sure to observe the following precautions; otherwise, the new equipment may adversely affect the engine control system and other electronic parts. WARNING ● A cellular phone should not be used for any purpose while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular phones while driving.
phone module when the ignition switch is placed in the ON position with the previously connected cellular phone turned on and carried in the vehicle. NOTE: Some devices require the user to accept connections to other Bluetooth姞 devices. If your phone does not connect automatically to the system, consult the phone’s Owner’s Manual for details on device operation. You can connect up to 5 different Bluetooth姞 cellular phones to the in-vehicle phone module.
● You will not be able to use a hands-free phone under the following conditions: – Your vehicle is outside of the cellular service area. ● If the hands-free phone system seems to be malfunctioning, see “Troubleshooting guide” in this section. You can also visit www.nissanusa.com/bluetooth for troubleshooting help. – Your vehicle is in an area where it is difficult to receive a cellular signal; such as in a tunnel, in an underground parking garage, near a tall building or in a mountainous area.
Initialization Giving voice commands When the ignition switch is placed in the ON position, NISSAN Voice Recognition is initialized, button is which takes a few seconds. If the pressed before the initialization completes, the system will announce “Hands-free phone system not ready” and will not react to voice commands. To operate NISSAN Voice Recognition, press button located on the and release the steering wheel. After the tone sounds, speak a command.
How to say numbers Example: 1-800-662-6200 NOTE: NISSAN Voice Recognition requires a certain way to speak numbers in voice commands. Refer to the following rules and examples. – “One eight zero zero” For best results, say phone numbers as single digits. ● Either “zero” or “oh” can be used for “0”. Example: 1-800-662-6200 – “One eight oh oh six six two six two oh oh”, or – “One eight zero zero six six two six two oh oh” ● Words can be used for the first 4 digits places only.
You can also use the button to interrupt the system feedback and give a command at once. See “List of voice commands” and “During a call” in this section for more information. LHA2454 CONTROL BUTTONS The control buttons for the Bluetooth姞 HandsFree Phone System are located on the steering wheel. PHONE/SEND Press the button to initiate a VR session or answer an incoming call.
NOTE: You must press the button within 5 seconds to change the language. 5. If you decide not to change the language, do not press either button. After 5 seconds, the VR session will end, and the language will not be changed. Connecting procedure NOTE: The connecting procedure must be performed when the vehicle is stationary. If the vehicle starts moving during the procedure, the procedure will be cancelled. Main Menu A “Connect phone” 䊊 B “Add phone” 䊊 C Initiate from handset 䊊 D Name phone 䊊 1.
four” as the 3rd group. For dialing more than 10 digits or any special characters, say “Special Number”. See “How to say numbers” in this section for more information. LIST OF VOICE COMMANDS Main Menu “Call” “Call” Main Menu “Call” 5. When you have finished speaking the phone number, the system repeats it back and announces the available commands. “Phonebook” A (Speak name) 䊊 “Recent Calls” “Phone Number” D . The system acknowledges 6. Say: “Dial” 䊊 the command and makes the call.
B (Speak Digits) 䊊 When prompted by the system, say the number you wish to call. Refer to “How to say numbers” and “Making a call by entering a phone number” in this section for more details. C “Special Number” 䊊 For dialing more than 10 digits or any special characters, say “Special Number”. When the system acknowledges the command, the system will prompt you to speak the number. D “Redial” 䊊 Use the Redial command to call the last number that was dialed.
“Phonebook” (phones without automatic phonebook download function) A “Transfer Entry” 䊊 Use the Transfer Entry command to store a new name in the system. When prompted by the system, say the name you would like to give the new entry. NOTE: The “Transfer Entry” command is not available when the vehicle is moving. Main Menu “Phonebook” For example, say: “Mary.” If the name is too long or too short, the system tells you, then prompts you for a name again.
“Phonebook” (phones with automatic phonebook download function) NOTE: The “Transfer Entry” command is not available when the vehicle is moving. Main Menu “Phonebook” Speak a Name A “List Names” 䊊 B “Record Name” 䊊 For phones that support automatic download of the phonebook (PBAP Bluetooth姞 profile), the “Phonebook” command is used to manage entries in the vehicle phonebook. You can say the name of an entry at this menu to initiate dialing of that entry.
C “Delete Phone” 䊊 “Connect Phone” NOTE: The Add Phone command is not available when the vehicle is moving. Main Menu “Connect Phone” Use the Delete Phone command to delete a phone that is connected to the vehicle. The system will list the names assigned to each phone and then prompt you for the phone you wish to delete. Deleting a phone from the vehicle will also delete that phonebook for that phone.
● next entry ● call eight oh five four one ● dial star two one seven oh ● correction ● yes ● connect phone ● no ● dial seven four oh one eight ● select ● previous entry ● The vehicle begins moving during VA mode. ● missed ● delete ● The ignition switch is placed in the OFF or LOCK position. ● dial eight five six nine two ● dial nine seven two six six 10. The system will announce that voice adaptation has been completed and the system is ready.
Operating tips ● To enter manual control mode, start the voice recognition system and tilt the tuning ) switch up or down. The system will ( speak ⬙Showing Manual Options⬙ when manual controls are initially activated. ● To browse the menu options, tilt the tuning ) switch up or down. The system will ( always speak the current menu option. Depending on the audio display, it will also show the current menu option. ● To select the current menu option, press the ) button.
TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved. Symptom System fails to interpret the command correctly. The system consistently selects the wrong entry from the phone book. Solution 1. Ensure that the command is valid. See “List of voice commands” in this section. 2.
BLUETOOTH姞 HANDS-FREE PHONE SYSTEM WITHOUT NAVIGATION SYSTEM (Type B) (if so equipped) WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. ● If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop your vehicle.
phone module when the ignition switch is placed in the ON position with the previously connected cellular phone turned on and carried in the vehicle. NOTE: Some devices require the user to accept connections to other Bluetooth姞 devices. If your phone does not connect automatic ally to the system, consult the phone’s Owner’s Manual for details on device operation. ● You will not be able to use a hands-free phone under the following conditions: – Your vehicle is outside of the cellular service area.
IC Regulatory information – Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. – This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. BLUETOOTH威 is a trademark owned by Bluetooth SIG, Inc. and licensed to Visteon.
● If you want to adjust the volume of the voice feedback, press the volume control switches (+ or -) on the steering wheel while being provided with feedback. You can also use the radio volume control knob. You can also use the button to interrupt the system feedback and give a command at once. See “List of voice commands” and “During a call” in this section for more information. ● In most cases you can interrupt the voice feedback to speak the next command by button on the steering pressing the wheel.
VOICE COMMANDS Voice commands can be used to operate the Bluetooth姞 Hands-Free Phone System. Press button and say “Phone” to bring up the the phone command menu. The available options are: ● Call ● Phonebook ● Recent Calls ● Send Text LHA2257 LHA2274 2. Use the TUNE/SCROLL knob to select “Bluetooth” and then press the ENTER button. 3. Use the TUNE/SCROLL knob to select “Add Phone or Device” and then press the ENTER button. 4.
● (a name) Say a name in the phonebook to bring up a list of options for that phonebook entry. The system will say the name it interpreted based on the voice command provided. If the name is incorrect, say “Correction” to hear another name. Once the correct phonebook entry is identified, say “Dial” to dial the number or “Send Text” to send a text message to that number. Say “Record Name” to record a name for the phonebook entry. Say “Delete Recording” to delete a recorded name for the phonebook entry.
“Send Text / Read Text” For more information on these commands, see “Text messaging” in this section. “Select Phone” Speak this command to select a phone to use from a list of those phones connected to the vehicle. MAKING A CALL To make a call from a phone connected to the vehicle’s Bluetooth姞 Hands-Free Phone System: ● Press the button. ● The system will prompt you for a command.
● “Transfer Call” – Speak this command to transfer the call to the handset. To transfer the call back from the handset to the Bluetooth姞 Hands-Free Phone System, button and confirm when press the prompted. If supported by the phone, the Bluetooth姞 Hands-Free Phone System allows for call waiting functionality. If a call is received while another call is already active, a message will be displayed on button to hold the the screen. Press the active call and switch to the second call.
Sending a text message: 1. Press the To send one of the custom messages, say “Custom Message”. If more than one custom message is stored, the system will prompt for the number of the desired custom message. For more information on setting and managing custom text messages, see “Bluetooth姞 settings” in this section. button. 2. Say “Send Text”. 3. The system will provide a list of available commands in order to determine the recipient of the text message.
● Call Back Speak this command to call the sender of the text message using the Bluetooth姞 Hands-Free Phone System. ● Send Text Speak this command to send a text message response to the sender of the text message. ● Read Text Speak this command to read the text message again. LHA2295 Reading a received text message: 1. Press the button. 2. Say “Read Text”. The text message, sender and delivery time are shown on the screen.
● Replace Phone Select to replace a phone from the displayed list. When a selection is made, the system will ask to confirm before proceeding. The recorded phonebook for the phone being deleted will be saved as long as the new phone’s phonebook is the same as the old phone’s phonebook. ● Select Phone or Device Select to connect to a previously connected phone from the displayed list. LHA2274 2.
BLUETOOTH姞 HANDS-FREE PHONE SYSTEM WITH NAVIGATION SYSTEM (if so equipped) ● Auto Reply Select to turn on or off the Auto Reply function. When enabled, the vehicle will automatically send a predefined text message to the sender when a text message is received while driving. ● Auto Reply Message Select to choose the message that is sent when the Auto Reply function is enabled. Choose from “I’m Driving” or one of the three custom messages stored in the system.
phone module when the ignition switch is placed in the ON position with the connected cellular phone turned on and carried in the vehicle. You can register up to 5 different Bluetooth姞 cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. NISSAN Voice Recognition system supports the phone commands, so dialing a phone number using your voice is possible. For more details, see “NISSAN Voice Recognition System” in this section.
– Your vehicle is in an area where it is difficult to receive cellular signal; such as in a tunnel, in an underground parking garage, near a tall building or in a mountainous area. – Your cellular phone is locked to prevent it from being dialed. ● When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person’s voice during a call.
CONNECTING PROCEDURE 1. Press the MENU button on the control panel. LHA2253 2. Select the “Settings” key. 4-112 Monitor, climate, audio, phone and voice recognition systems LHA2248 3. Select the “Phone & Bluetooth” key.
LHA2265 LHA2297 4. Select the “Connect New Device” key. VEHICLE PHONEBOOK 5. Initiate the connecting process from the handset. The system will display the message: “Is PIN XXXXXX displayed on your Bluetooth device?”. If the PIN is displayed on your Bluetooth姞 device, select “Yes” to complete the connecting process. To access the vehicle phonebook: For more information, see the Bluetooth姞 device’s Owner’s Manual. 1. Press the button on the control panel. 2. Select the “Phonebook” key. LHA2279 3.
● “Redial”: Dial the last outgoing call from the vehicle. ”: Input the phone number manually ● “ using a keypad displayed on the screen. For information on how to use the touchscreen, see “How to use the touchscreen” in this section. LHA2297 LHA2298 MAKING A CALL RECEIVING A CALL To make a call, follow the procedure below: When a call is placed to the connected phone, the display will change to phone mode. 1. Press the button on the instrument panel. The “Phone” screen will appear on the display. 2.
ENDING A CALL To end a phone call, select the red phone ( ) icon on the screen or press the button on the steering wheel. LHA2299 DURING A CALL While a call is active, the following options are available on the screen: ● “Handset” Select this option to switch control of the phone call over to the handset. ● “Mute Mic.” Select this option to mute the microphone. Select again to unmute the microphone. ) icon ● Red phone ( Select to end the phone call.
The system allows for the sending and receiving of text messages through the vehicle interface. ● “On my way” Sending a text message: ● “Okay” 1. Press the button. 2. Say “Send Text”. 3. The system will provide a list of available commands in order to determine the recipient of the text message. Choose from the following: ● “Running late” To send one of the custom messages, say “Custom Messages”.
● Call Back Speak this command to call the sender of the text message using the Bluetooth姞 Hands-Free Phone System. ● Send Text Speak this command to send a text message response to the sender of the text message. ● Read Text Speak this command to read the text message again. ● Previous Text Speak this command to move to the previous text message (if available). ● Next Text Speak this command to move to the next text message (if available). LHA2253 BLUETOOTH SETTINGS LHA2248 3.
● Replace Connected Device Select to replace a Bluetooth姞 device from a list of those devices connected to the Bluetooth姞 Hands-Free Phone System. ● Delete Connected Device Select to delete a Bluetooth姞 device from a list of those devices connected to the Bluetooth姞 Hands-Free Phone System. ● Bluetooth Select to toggle the Bluetooth姞 on and off. LHA2265 ● Phone Settings See “Phone settings” in this section for more information.
NISSAN VOICE RECOGNITION SYSTEM (if so equipped) ● Use Phonebook From: Select “Handset” to use the phone’s phonebook. Select “SIM” to use the phonebook on the SIM card. Select “Both” to use both sources. ● Download Phonebook Now Select to download the phonebook to the vehicle from the chosen source. ● Phone Notifications for Select “Driver” to have phone notifications shown in the vehicle information display.
● If the command is not recognized, the system announces: “Command not recognized.” Repeat the command in a clear voice. ● If you want to cancel the command or go back to the previous menu of commands, button. The system will anpress the nounce: “Voice recognition canceled” or “Go back” depending on the current menu level. ● Press the BACK button on the control panel to move back through the menus displayed on the screen. LHA2522 Giving voice commands 1. Press the button.
● Wait until a tone sounds before speaking a command. Otherwise, the command will not be received properly. How to say numbers NISSAN Voice Recognition requires a certain way to speak numbers in voice commands. Refer to the following examples. ● Start speaking a command within 3.5 seconds after the tone sounds. General rule: Either “zero” or “oh” can be used for “0”. ● Speak in a natural voice without pausing between words. Phone numbers Speak phone numbers according to the following example.
BLUETOOTH姞 HANDS-FREE PHONE SYSTEM VOICE COMMANDS To access the Bluetooth姞 Hands-Free Phone System voice commands: 1. Press the button. 2. Say “Call” and then a name in the vehicle phonebook to call that entry. Otherwise, say “Phone” to access various phone commands. If the Bluetooth姞 has been set to “Off”, the system announces: “Bluetooth姞 is off.
● Address Book ● Home ● Previous Destination For more information about these commands, see the separate Navigation System Owner’s Manual. AUDIO SYSTEM VOICE COMMANDS To access the audio system voice commands: ● CD Switches the audio system to the CD mode. A CD must be inserted for this command to be functional. ● iPod姞 Switches the audio system to the iPod姞 mode. An iPod姞 must be connected for this command to be available and functional. The following sub-commands are available for iPod姞: 1.
INFORMATION VOICE COMMANDS The following voice commands are available for the information functions of the Navigation System: ● Traffic ● Current Weather ● Weather Forecast ● Google™ Send-To-Car ● POIs Powered by Google™ For more information about these commands, see the separate Navigation System Owner’s Manual. HELP VOICE COMMANDS The following voice commands can be spoken to have the system provide instructions and tips for using the NISSAN Voice Recognition system.
TROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty. If problems are encountered, follow the solutions given in this guide for the appropriate error. Where the solutions are listed by number, try each solution in turn, starting with number one, until the problem is resolved. Symptom/error message The system responds “Command Not Recognized” or the system fails to recognize the command correctly. Solution 1. Ensure that the command format is valid.
MEMO 4-126 Monitor, climate, audio, phone and voice recognition systems
5 Starting and driving Precautions when starting and driving. . . . . . . . . . . . . . . . 5-2 Exhaust gas (carbon monoxide) . . . . . . . . . . . . . . . . . . 5-2 Three-way catalyst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 On-pavement and off-road driving precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 5-3 Avoiding collision and rollover . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS WHEN STARTING AND DRIVING WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.
● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously reduce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunctions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale.
WARNING ● If the low tire pressure warning light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with underinflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires.
For Canada: This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, include interference that may cause undesired operation of the device. 3. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.
Help prevent rapid air pressure loss by maintaining the correct air pressure and visually inspect the tires for wear and damage. See “Wheels and tires” in the “Maintenance and do-it-yourself” section of this manual. If a tire rapidly loses air pressure or “blows-out” while driving, maintain control of the vehicle by following the procedure below. Please note that this procedure is only a general guide. The vehicle must be driven as appropriate based on the conditions of the vehicle, road and traffic.
Please observe the following precautions: WARNING ● Drive carefully when off the road and avoid dangerous areas. Every person who drives or rides in this vehicle should be seated with their seat belt fastened. This will keep you and your passengers in position when driving over rough terrain. ● Do not drive across steep slopes. Instead drive either straight up or straight down the slopes. Off-road vehicles can tip over sideways much more easily than they can forward or backward.
IGNITION SWITCH ● Do not attempt to test a 4WD equipped vehicle on a 2-wheel dynamometer (such as the dynamometers used by some states for emissions testing), or similar equipment even if the other two wheels are raised off the ground. Make sure you inform test facility personnel that your vehicle is equipped with 4WD before it is placed on a dynamometer.
To remove the key from the ignition switch: 1. Shift the shift selector to the P (Park) position with the ignition switch in the ON position. 2. Place the ignition switch in the LOCK position. 3. Remove the key from the ignition switch. WSD0041 If the shift selector is shifted to the P (Park) position after the ignition switch is placed in the OFF position or when the ignition switch cannot be placed in the LOCK position, proceed as follows to remove the key. AUTOMATIC TRANSMISSION 1.
BEFORE STARTING THE ENGINE IGNITION SWITCH POSITIONS LOCK: Normal parking position (0) OFF: (1) The engine can be turned off without locking the steering wheel. ACC: (Accessories) (2) This position activates electrical accessories such as the radio when the engine is not running. ON: Normal operating position (3) This position turns on the ignition system and the electrical accessories. START: (4) This position starts the engine. As soon as the engine has started, release the key.
STARTING THE ENGINE 1. Apply the parking brake. 2. Move the shift selector to P (Park) or N (Neutral). P (Park) is recommended. The shift selector cannot be moved out of P (Park) and into any of the other gear positions if the ignition switch is turned to the OFF position or if the key is removed from the ignition switch. The starter is designed not to operate if the shift selector is in any of the driving positions. 3.
DRIVING THE VEHICLE ENGINE PROTECTION MODE The engine has an engine protection mode to reduce the chance of damage if the coolant temperature becomes too high (for example, when climbing steep grades in high temperature with heavy loads, such as when towing a trailer). When the engine temperature reaches a certain level: ● The engine coolant temperature gauge will move toward the H position. ● Engine power may be reduced.
AUTOMATIC TRANSMISSION WARNING ● Do not depress the accelerator pedal while shifting from P (Park) or N (Neutral) to R (Reverse), or L (Low). Always depress the brake pedal until shifting is completed. Failure to do so could cause you to lose control and have an accident. ● Cold engine idle speed is high, so use caution when shifting into a forward or reverse gear before the engine has warmed up. ● Never shift to P (Park) or R (Reverse) while the vehicle is moving. This could cause an accident.
WARNING Apply the parking brake if the shift selector is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage WSD0187 To move the shift selector: : Shift while depressing the brake pedal : Shift without depressing brake pedal Shifting – console After starting the engine, fully depress the brake pedal and move the shift selector out of the P (Park) position.
4H: 4LO: 62 MPH (100 km/h) 31 MPH (50 km/h) w/o tow mode 4LO: 27 MPH (44 km/h) w/tow mode 31 MPH (50 km/h) 3 (Third gear): Use this position for driving up and down long slopes where engine braking would be advantageous. 2 (Second gear): Use this position for hill climbing or engine braking on downhill grades. Do not downshift into the 2 position at speeds over the following and do not exceed the following speeds in the 2 position.
WARNING Apply the parking brake if the shift selector is in any position while the engine is not running. Failure to do so could cause the vehicle to move unexpectedly or roll away and result in serious personal injury or property damage. If the key is turned to the OFF or ACC position for any reason while the vehicle is in N (Neutral), or any D (Drive) position, the key cannot be turned to the LOCK position and be removed from the ignition switch.
M4 (Fourth): M1 (First): For driving up or down long slopes where engine braking would be advantageous. Use this position when climbing steep hills slowly or driving slowly through deep snow, sand or mud, or for maximum engine braking on steep downhill grades. Shift ranges up or down one by one as follows: M1 ←→ M2 ←→ M3 ←→ M4 M4 will be displayed on the position indicator in the meter. M3 (Third): M1 will be displayed on the position indicator on the meter.
5. Use a protective cloth on the end of a small screwdriver before inserting it in the shift lock release slot and pushing down. 6. Move the shift selector to the N (Neutral) position while holding down the shift lock release. 7. For models without the NISSAN vehicle immobilizer system, turn the key to the ON position to unlock the steering wheel. 8. Now the vehicle may be moved to the desired location.
PARKING BRAKE Accelerator downshift — in D position — For passing or hill climbing, depress the accelerator pedal to the floor. This shifts the transmission down into a lower gear, depending on the vehicle speed. WARNING ● Be sure the parking brake is fully released before driving. Failure to do so can cause brake failure and lead to an accident. Fail-safe ● Do not release the parking brake from outside the vehicle.
CRUISE CONTROL (if so equipped) PRECAUTIONS ON CRUISE CONTROL ● If the cruise control system malfunctions, it cancels automatically. The SET indicator light in the vehicle information display then blinks to warn the driver, see “Vehicle information display” in the “Instruments and controls” section. ● If the SET indicator light blinks, push the cruise control ON·OFF switch off and have the system checked by a NISSAN dealer. LSD2003 1. 2. 3. 4.
BREAK-IN SCHEDULE To cancel the preset speed, use one of the following three methods. ● Push the CANCEL button; the SET indicator light in the vehicle information display goes out. ● Tap the brake pedal; the SET indicator light goes out. ● Push the ON·OFF switch off. Both the CRUISE indicator light and SET indicator light in the vehicle information display go out. ● Push and hold the ACCEL/RES switch. When the vehicle attains the speed you desire, release the switch.
INCREASING FUEL ECONOMY USING FOUR WHEEL DRIVE (4WD) (if so equipped) ● Accelerate slowly and smoothly. Maintain cruising speeds with a constant accelerator position. ● When cruising at highway speeds, it is more economical to use the air conditioner and leave the windows closed to reduce drag. ● Drive at moderate speeds on the highway. Driving at high speed lowers fuel economy. , use 4H ● For vehicles equipped with or 4L position only when necessary. Fourwheel drive operation lowers fuel economy.
CAUTION ● Do not drive the vehicle in the 4H or 4LO position on dry hard surface roads. Driving on dry, hard surfaces in 4H or 4LO may cause unnecessary noise, tire wear and increased fuel consumption. If the 4WD warning light turns on when you are driving on dry hard surface roads: – in the 4H position, shift the 4WD shift switch to 2WD. – in the 4LO position, stop the vehicle, move the shift selector to the N (Neutral) position with the brake pedal depressed, and shift the 4WD shift switch to 2WD.
4WD Shift Switch Position Wheels Driven 4WD shift Indicator Light Transfer 4LO position Rear wheels For driving on dry, paved roads (Economy drive) 4 wheels For driving on rocky, sandy or snowcovered roads 2WD 4H Use Conditions Neutral *1 May blink Neutral disengages the automatic transmission mechanical parking lock, which will allow the vehicle to roll. Do not leave the transfer shift position in Neutral.
The transfer case 4WD shift switch is used to select either 2WD or 4WD depending on the driving conditions. There are three types of drive modes available, 2WD, 4H and 4LO. The 4WD shift switch electronically controls the transfer case operation. Rotate the switch to move between each mode, 2WD, 4H and 4LO. To change into or out of 4LO, the vehicle MUST be stationary, shift the shift selector to neutral, and depress the brake pedal. The switch must be pushed and turned to select 4LO.
● If it is difficult to free the vehicle, rock the vehicle back and forth between reverse and drive gears. ● When the vehicle is stopped after making a turn, you may feel a slight jolt after the shift selector is shifted to N or P. This occurs because the transfer clutch is released and not because of a malfunction. ● If the vehicle is stuck deep in mud, place stones or wooden blocks under the tires. Then try the recovery procedures above. Tire chains may be effective.
● If the 4WD warning light comes on, the 4WD indicator light goes out. CAUTION LSD0147 4WD shift indicator light The 4WD shift indicator light is located in the vehicle information display. ● If the 4WD shift indicator light indication changes to 2WD when the 4WD shift switch is shifted to the 4H position at low ambient temperatures, the 2WD mode may be being engaged due to malfunctioning drive system.
ELECTRONIC LOCKING REAR DIFFERENTIAL (E-Lock) SYSTEM (if so equipped) ● When the warning light comes on, the 2WD mode may be engaged even if the 4WD shift switch is in 4H. Be especially careful when driving. If corresponding parts are malfunctioning, the 4WD mode will not be engaged even if the 4WD shift switch is shifted. ● Do not drive the vehicle in the 4H or 4LO position on dry hard surface roads.
WARNING ● Never leave the E-Lock system ON when driving on paved or hard-surfaced roads. Turning the vehicle may result in the rear wheels slipping and result in an accident and personal injury. After using the E-Lock system to free the vehicle, turn the system OFF. ● Use the E-Lock system only when freeing a stuck vehicle. Try the 4LO position before using the E-Lock system. Never use the E-Lock system on a slippery road surface such as snow or ice surface.
PARKING/PARKING ON HILLS A ● HEADED DOWNHILL WITH CURB: 䊊 Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb. B ● HEADED UPHILL WITH CURB: 䊊 Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb. ● HEADED UPHILL OR DOWNHILL, NO C CURB: 䊊 WSD0050 WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.
POWER STEERING BRAKE SYSTEM The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. The brake system has two separate hydraulic circuits. If one circuit malfunctions, you will still have braking at 2 wheels. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds.
This procedure is described in the vehicle service manual and can be performed by a NISSAN dealer. ANTI-LOCK BRAKING SYSTEM (ABS) WARNING ● The Anti-lock Braking System (ABS) is a sophisticated device, but it cannot prevent accidents resulting from careless or dangerous driving techniques. It can help maintain vehicle control during braking on slippery surfaces. Remember that stopping distances on slippery surfaces will be longer than on normal surfaces even with ABS.
ACTIVE BRAKE LIMITED SLIP (ABLS) SYSTEM When the ABS senses that 1 or more wheels are close to locking up, the actuator rapidly applies and releases hydraulic pressure. This action is similar to pumping the brakes very quickly. You may feel a pulsation in the brake pedal and hear a noise from under the hood or feel a vibration from the actuator when it is operating. This is normal and indicates that the ABS is operating properly.
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM The Vehicle Dynamic Control (VDC) system uses various sensors to monitor driver inputs and vehicle motion. Under certain driving conditions, the VDC System helps to perform the following functions: ● Controls brake pressure to reduce wheel slip on one slipping drive wheel so power is transferred to a non slipping drive wheel on the same axle. ● Controls brake pressure and engine output to reduce drive wheel slip based on vehicle speed (traction control function).
REAR SONAR SYSTEM (if so equipped) ● Do not modify the vehicle’s suspension. If suspension parts such as shock absorbers, struts, springs, stabilizer bars, bushings and wheels are not NISSAN recommended for your vehicle or are extremely deteriorated, the VDC system may not operate properly. This could adversely affect vehicle handling perindicator may formance, and the flash or the indicator light may illuminate.
COLD WEATHER DRIVING ● The system is designed as an aid to the driver in detecting large stationary objects to help avoid damaging the vehicle. The system will not detect small objects below the bumper, and may not detect objects close to the bumper or on the ground. ● If your vehicle sustains damage to the rear bumper fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms.
DRAINING OF COOLANT WATER If the vehicle is to be left outside without antifreeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see “Changing engine coolant” in the “Maintenance and do-it-yourself” section of this manual. TIRE EQUIPMENT 1. SUMMER tires have a tread designed to provide superior performance on dry pavement. However, the performance of these tires will be substantially reduced in snowy and icy conditions.
ENGINE BLOCK HEATER (if so equipped) To use the engine block heater: 1. Turn the engine off. Engine block heaters are used to assist with cold temperature starting. 2. Open the hood and unwrap the engine block heater cord. The engine block heater should be used when the outside temperature is 20°F (-7°C) or lower. 3. Plug the engine block heater cord into a grounded 3-wire, 3-pronged extension cord.
MEMO 5-40 Starting and driving
6 In case of emergency Hazard warning flasher switch . . . . . . . . . . . . . . . . . . . . . . 6-2 Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Tire Pressure Monitoring System (TPMS). . . . . . . . . . 6-2 Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 Push starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HAZARD WARNING FLASHER SWITCH FLAT TIRE The flashers will operate with the ignition switch placed in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving. LIC0394 Push the switch on to warn other drivers when you must stop or park under emergency conditions. All turn signal lights flash. WARNING ● If stopping for an emergency, be sure to move the vehicle well off the road.
WARNING ● Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use. ● If the low tire pressure warning light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible.
Getting the spare tire and tools 1. Fold up the rear bench seat. Refer to “Folding the rear bench seat” in the “Safety – Seats, seat belts and supplemental restraint system” section of this manual. WCE0044 Blocking wheels 1 at both the front and Place suitable blocks 䊊 back of the wheel diagonally opposite the flat tire 2 to prevent the vehicle from moving when it is 䊊 jacked up. WARNING Be sure to block the wheel as the vehicle may move and result in personal injury.
CAUTION Be sure to center the spare tire suspending plate on the wheel and then lift the spare tire. Jacking up vehicle and removing the damaged tire WARNING WCE0150 WCE0151 3. Assemble the two pieces of the jack rod. Find the oval-shaped opening above the middle of the license plate. Pass the T-shaped end of the jack rod through the opening and direct it toward the spare tire winch, located directly above the spare tire. 4.
● Do not start or vehicle is on the vehicle to move. for vehicles differentials. run the engine while jack. It may cause the This is especially true with limited slip ● Do not allow passengers to stay in the vehicle while it is on the jack. ● Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move. Always refer to the illustration for the correct placement and jack-up points for your specific vehicle model and jack type.
4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated. Lower the vehicle completely. WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could cause an accident. WCE0063 Installing the spare tire The spare tire is designed for emergency use.
JUMP STARTING Adjust tire pressure to the COLD pressure. COLD pressure: After vehicle has been parked for three hours or more or driven less than 1 mi. (1.6 km). COLD tire pressures are shown on the Tire and Loading Information label affixed to the driver side center pillar. After adjusting tire pressure to the COLD tire pressure, the display (if so equipped) of the tire pressure information may show higher pressure than the COLD tire pressure after the vehicle has been driven more than 1 mi. (1.6 km).
● Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting. ● Do not attempt to jump start a frozen battery. It could explode and cause serious injury. WCE0054 WARNING Always follow the instructions below. Failure to do so could result in damage to the charging system and cause personal injury. 3.
PUSH STARTING CAUTION WARNING ● Always connect positive (⫹) to positive (⫹) and negative (⫺) to body ground (for example, strut mounting bolt, engine lift bracket, etc.) — not to the battery. Do not push start this vehicle. The threeway catalyst may be damaged. ● Make sure the jumper cables do not touch moving parts in the engine compartment and that the cable clamps do not contact any other metal. Automatic transmission models cannot be push-started or tow-started.
TOWING YOUR VEHICLE 3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or coolant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen. 4. Open the engine hood. WARNING If steam or water is coming from the engine, stand clear to prevent getting burned. 5. Visually check drive belts for damage or looseness. Also check if the cooling fan is running.
For information about towing your vehicle behind a recreational vehicle (RV), refer to “Flat towing” in the “Technical and consumer information” section of this manual. Two-wheel drive models NISSAN recommends that your vehicle be towed with the driving (rear) wheels off the ground or place the vehicle on a flat bed truck as illustrated.
LCE0083 WCE0161 Four-wheel drive models NISSAN recommends that towing dollies be used when towing your vehicle or place the vehicle on a flat bed truck as illustrated. CAUTION Never tow 4WD models with any of the wheels on the ground as this may cause serious and expensive damage to the transfer case and transmission.
● Attach recovery devices only to main structural members of the vehicle or the recovery hooks. Rocking a stuck vehicle ● Do not use the vehicle tie-downs to tow or free a stuck vehicle. ● Stand clear of a stuck vehicle. ● Only use devices specifically designed for vehicle recovery and follow the manufacturer’s instructions. ● Always pull the recovery device straight out from the front of the vehicle. Never pull at an angle. WARNING ● Do not spin your tires at high speed.
7 Appearance and care Cleaning exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Waxing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Removing spots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Underbody . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Glass . . . . . . . . . . . . . . . . . . . . . . .
CLEANING EXTERIOR In order to maintain the appearance of your vehicle, it is important to take proper care of it. To protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads. ● when contaminants such as soot, bird droppings, tree sap, metal particles or bugs get on the paint surface. ● when dust or mud builds up on the surface.
REMOVING SPOTS CAUTION Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store. When cleaning the inside of the windows, do not use sharp-edged tools, abrasive cleaners or chlorine-based disinfectant cleaners. They could damage the electrical conductors, radio antenna elements or rear window defroster elements.
CLEANING INTERIOR Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry, soft cloth. Regular care and cleaning is required in order to maintain the appearance of the leather. Before using any fabric protector, read the manufacturer’s recommendations.
CORROSION PROTECTION SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemental restraint system” section of this manual. WARNING LAI0009 Floor mat positioning aid This vehicle includes two driver’s side front floor mat brackets and one passenger’s side front floor mat bracket to help keep your floor mats in place.
Temperature CAUTION Air pollution ● NEVER remove dirt, sand or other debris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. Industrial pollution, the presence of salt in the air in coastal areas, or heavy road salt use accelerates the corrosion process. Road salt also accelerates the disintegration of paint surfaces. ● Never allow water or other liquids to come in contact with electronic components inside the vehicle as this may damage them.
8 Maintenance and do-it-yourself Maintenance requirements. . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Explanation of general maintenance items . . . . . . . . . 8-2 Maintenance precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Engine compartment check locations . . . . . . . . . . . . . . . . 8-6 Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE REQUIREMENTS Your NISSAN has been designed to have minimum maintenance requirements with long service intervals to save you both time and money. However, some day-to-day and regular maintenance is essential to maintain your NISSAN’s good mechanical condition, as well as its emissions and engine performance. It is the owner’s responsibility to make sure that the scheduled maintenance, as well as general maintenance, is performed.
When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim. Road wheel nuts (lug nuts)* When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary.
Steering wheel Check for changes in the steering system, such as excessive freeplay, hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly. Windshield wiper and washer* Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner.
MAINTENANCE PRECAUTIONS When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precautions which should be closely observed. WARNING ● Park the vehicle on a level surface, apply the parking brake securely and block the wheels to prevent the vehicle from moving.
ENGINE COMPARTMENT CHECK LOCATIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Battery Fuse/fusible link box Transmission dipstick Engine oil filler cap Brake fluid reservoir Windshield-washer fluid reservoir Air cleaner Drive belt location Radiator cap Power steering fluid reservoir Engine oil dipstick Engine coolant reservoir NOTE: Engine cover removed for clarity.
ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with a pre-diluted mixture of 50% Genuine NISSAN Long Life Antifreeze/Coolant (blue) and 50% water to provide year-round anti-freeze and coolant protection. The antifreeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary. WARNING ● Never remove the radiator or coolant reservoir cap when the engine is hot. Wait until the engine and radiator cool down.
This vehicle contains Genuine NISSAN Long Life Antifreeze/Coolant (blue). The life expectancy of the factory-fill coolant is 105,000 miles (168,000 km) or 7 years. Mixing any other type of coolant or the use of non-distilled water will reduce the life expectancy of the factory-fill coolant. Refer to the NISSAN Service and Maintenance Guide for more details. The engine coolant reservoir is a pressurized tank. When installing the cap, tighten.
ENGINE OIL CAUTION Oil level should be checked regularly. Operating the engine with an insufficient amount of oil can damage the engine, and such damage is not covered by warranty. LDI0370 CHECKING ENGINE OIL LEVEL 1. Park the vehicle on a level surface and apply the parking brake. 2. Start the engine and let it idle until it reaches operating temperature. 3. Turn off the engine. Wait more than 10 minutes for the oil to drain back into the oil pan. 4. Remove the dipstick and wipe it clean.
If the oil filter is to be changed, remove and replace it at this time. See “Changing engine oil filter” in this section. 7. Refill engine with recommended oil through the oil filler opening, then install the oil filler cap securely. ● Waste oil must be disposed of properly. See “Capacities and recommended fuel/lubricants” in the “Technical and consumer information” section of this manual for drain and refill capacity. ● Check your local regulations.
5-SPEED AUTOMATIC TRANSMISSION FLUID 5. Wipe the engine oil filter sealing surface with a clean rag. CAUTION WDI0505 1. Park the vehicle on a level surface and apply the parking brake. 2. Turn the engine off. CAUTION Be sure to remove any old gasket material remaining on the sealing surface of the engine. Failure to do so could lead to an oil leak and engine damage. ● Use Genuine NISSAN Matic S ATF. If Genuine NISSAN Matic S ATF is not available, Genuine NISSAN Matic J ATF may also be used. 6.
POWER STEERING FLUID BRAKE FLUID CAUTION ● DO NOT OVERFILL. ● Recommended fluid is NISSAN PSF or equivalent. Genuine For further brake fluid specification information, refer to “Capacities and recommended fuel/lubricants” in the “Technical and consumer information” section of this manual. WARNING ● Use only new fluid from a sealed container. Old, inferior or contaminated fluid may damage the brake system. The use of improper fluids can damage the brake system and affect the vehicle’s stopping ability.
WINDSHIELD-WASHER FLUID Refill the reservoir more frequently when driving conditions require an increased amount of windshield-washer fluid. Recommended fluid is Genuine NISSAN Windshield Washer Concentrate Cleaner & Antifreeze or equivalent. CAUTION ● Do not substitute engine anti-freeze coolant for windshield-washer fluid. This may result in damage to the paint. LDI0374 BRAKE FLUID Check the brake fluid level in the reservoir.
BATTERY ● Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water. ● Make certain the terminal connections are clean and securely tightened. ● If the vehicle is not to be used for 30 days or longer, disconnect the negative (-) battery terminal cable to prevent discharge. NOTE: Care should be taken to avoid situations that can lead to potential battery discharge and potential no-start conditions such as: 1.
Vehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary, see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN dealer. WDI0224 1. Remove the vent caps with a screwdriver as shown. Use a cloth to protect the battery case. WDI0529 2. Check the fluid level in each cell.
VARIABLE VOLTAGE CONTROL SYSTEM DRIVE BELT A is located near the battery The current sensor 䊊 along the negative battery cable. If you add electrical accessories to your vehicle, be sure to ground them to a suitable body ground such as the frame or engine block area. WDI0566 CAUTION ● Do not ground accessories directly to the battery terminal. Doing so will bypass the variable voltage control system and the vehicle battery may not charge completely.
SPARK PLUGS 1. Visually inspect the belt for signs of unusual wear, cuts, fraying or looseness. If the belt is in poor condition or is loose, have it replaced or adjusted by a NISSAN dealer. WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely. 2. Have the belt checked regularly for condition and tension in accordance with the maintenance schedule found in the “NISSAN Service and Maintenance Guide”.
AIR CLEANER NOTE: After installing a new air cleaner, make sure the air cleaner cover is seated in the housing and latch the clips. WARNING WDI0712 The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the “NISSAN Service and Maintenance Guide.” To remove the air cleaner filter: 1 䊊 Unlatch the clips and move the air cleaner cover upward. 2. Remove the air cleaner filter. 3.
WDI0619 LDI0387 1. Remove the 2 lower glove box hinge pins A . Remove the glove box from the opening 䊊 and let it hang by the cord. 2. Remove the filter cover bolt and remove the filter cover. 3. Remove the old in-cabin microfilters. LDI0404 NOTE: The filters are marked with air flow arrows. The end of the filter with the arrow should face the rear of the vehicle. The arrows should face downward. 4. Insert the first filter into the housing and slide it over to the right.
WINDSHIELD WIPER BLADES 6. Return the wiper to its original position and release it until it has made contact with the windshield. CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. CAUTION ● After wiper blade replacement, return the wiper arm to its original position; otherwise it may be damaged when the hood is opened.
BRAKES If the brakes do not operate properly, have the brakes checked by a NISSAN dealer. Self-adjusting brakes Your vehicle is equipped with self-adjusting brakes. Proper brake inspection intervals should be followed. For more information regarding brake inspections, see the appropriate maintenance schedule information in the “NISSAN Service and Maintenance Guide”. The front and rear disc-type brakes self-adjust every time the brake pedal is applied.
FUSES LDI0455 A is used in Two types of fuses are used. Type 䊊 the fuse boxes in the engine compartment. Type B is used in the passenger compartment fuse 䊊 box. Type A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box. Type A fuses can be installed in the engine compartment and passenger compartment fuse boxes. LDI0457 If a type A fuse is used to replace a type B fuse, the type A fuse will not be level with the fuse pocket as shown in the illustration.
3. Remove the fuse box cover by pushing the tab and lifting the cover up. 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. WDI0452 A , replace it with a new 5. If the fuse is open 䊊 B. fuse 䊊 6. If a new fuse also opens, have the electrical system checked and repaired by a NISSAN dealer. LDI0381 Fusible links If the electrical equipment does not operate and fuses are in good condition, check the fusible links.
3. Pull the fuse box cover to remove. 4. Remove the fuse with the fuse puller. WDI0452 LDI0618 PASSENGER COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight switch are OFF. 2. Open the glove box to access the fuse box cover.
How to replace the extended storage switch: 1. To remove the extended storage switch, be sure the ignition switch is in the OFF or LOCK position. 2. Be sure the headlight switch is in the OFF position. 3. Remove the fuse box cover. 1 found on each 4. Pinch the locking tabs 䊊 side of the storage switch. 5. Pull the storage switch straight out from the 2 .
BATTERY REPLACEMENT CAUTION Be careful not to allow children to swallow the battery or removed parts. LDI2026 KEYFOB (if so equipped) Replace the battery in the keyfob as follows: 1 䊊 2 䊊 8-26 Maintenance and do-it-yourself A. Open the lid using a coin 䊊 B. Remove the battery 䊊 3 䊊 C with the “+” facing Install a new battery 䊊 down. ● Hold the battery by the edges. Holding the battery across the contact points will seriously deplete the storage capacity.
LIGHTS ● Do not touch the internal circuit and electric terminals as it could cause a malfunction. ● When changing the battery, do not let dust or oil get on the keyfob. ● There is danger of explosion if a lithium battery is incorrectly replaced. Replace only with the same or equivalent type. Recommended battery: CR2025 or equivalent. 4 䊊 Close the lid securely. button, then the 5. Press the button two or three times to check the keyfob operation.
NOTE: NOTE: Use the same number and wattage as shown in the chart. To adjust the fog light vertical aim: Access the aiming screw from underneath the front bumper. The aiming screw is located on the bottom of the fog light housing. Turn the screw clockwise to raise the pattern. Turn the screw counterclockwise to lower the pattern. Fog may temporarily form inside the lens of the exterior lights in the rain or in a car wash.
EXTERIOR AND INTERIOR LIGHTS Item Headlight assembly High Low Park/Turn Sidemarker Side turn signal light* (if so equipped) Front fog light (if so equipped) Puddle light (if so equipped) Room/map lights (front) Personal lights Vanity mirror light (if so equipped) Step light (if so equipped) High-mounted stop light/cargo lights* Rear combination light Tail/Stop Backup (reversing) Turn Tailgate light (if so equipped) License plate light Wattage (W) Bulb No. 65 55 28/8 3.8 — 27.5 9 6 8 1.8 3.8 12.
1. 2. 3. 4. 5. 6. 7. 8. 9. Room/map light (if so equipped) Personal lights (if so equipped) Step light (if so equipped) Puddle light/Side turn signal light (if so equipped) High-mount stoplight/cargo lights License plate light Rear combination/tailgate light (if so equipped) assembly Fog light (if so equipped) Headlight assembly WDI0263 Replacement procedures WDI0409 8-30 Maintenance and do-it-yourself All other lights are either type A, B, C or D.
LDI0364 Personal lights (If so equipped) 1 to protect the housing. Use a cloth 䊊 LDI0385 Vanity mirror (If so equipped) 1 to protect the housing. Use a cloth 䊊 LDI0389 Interior/map lights 1 to protect the housing.
LDI0341 Step light (If so equipped) 1 to protect the housing. Use a cloth 䊊 8-32 Maintenance and do-it-yourself LDI0388 Puddle light (If so equipped) 1 to protect the housing.
WHEELS AND TIRES If you have a flat tire, see “Flat tire” in the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) LDI0410 Rear combination light This vehicle is equipped with the Tire Pressure Monitoring System (TPMS). It monitors tire pressure of all 4 tires except the spare.
The tire pressures should be checked when the tires are cold. The tires are considered COLD after the vehicle has been parked for 3 or more hours, or driven less than 1 mile (1.6 km) at moderate speeds. Incorrect tire pressure, including under inflation, may adversely affect tire life and vehicle handling. WARNING ● Improperly inflated tires can fail suddenly and cause an accident. ● The Gross Vehicle Weight Rating (GVWR) is located on the F.M.V.S.S./C.M.V.S.S. certification label.
5 䊊 6 䊊 Tire size - refer to “Tire labeling” later in this section. Spare tire size. LDI0485 Tire and loading information label 1 䊊 2 䊊 3 䊊 Seating capacity: The maximum number of occupants that can be seated in the vehicle. Vehicle load limit: See loading information in the “Technical and consumer information” section. Original tire size: The size of the tires originally installed on the vehicle at the factory. 4 䊊 Cold tire pressure: Inflate the tires to this pressure when the tires are cold.
3. Remove the gauge. 4. Read the tire pressure on the gauge stem and compare to the specification shown on the Tire and Loading Information label. 5. Add air to the tire as needed. If too much air is added, press the core of the valve stem briefly with the tip of the gauge stem to release pressure. Recheck the pressure and add or release air as needed. LDI0393 Checking tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem.
WDI0394 Example TIRE LABELING Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be used to identify the tire in case of a recall. WDI0395 Example 1 Tire size (example: P215/65R15 95H) 䊊 1.
3 Tire ply composition and material 䊊 The number of layers or plies of rubbercoated fabric in the tire. Tire manufacturers also must indicate the materials in the tire, which include steel, nylon, polyester, and others. 4 Maximum permissible inflation pres䊊 sure WDI0396 Example 2 TIN (Tire Identification Number) for a 䊊 new tire (example: DOT XX XX XXX XXXX) 1. DOT: Abbreviation for the “Department Of Transportation”.
7 The word “radial” 䊊 The word “radial” is shown if the tire has radial structure. 8 Manufacturer or brand name 䊊 Manufacturer or brand name is shown.
Generally, snow tires have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed. Never exceed the maximum speed rating of the tire. If you install snow tires, they must be the same size, brand, construction and tread pattern on all four wheels. For additional traction on icy roads, studded tires may be used. However, some U.S. states and Canadian provinces prohibit their use. Check local, state and provincial laws before installing studded tires.
Wheel nut tightening torque: ● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced. 98 ft-lb (133 N·m) The wheel nuts must be kept tightened to specifications at all times. It is recommended that wheel nuts be tightened to specification at each tire rotation interval. ● Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be obvious.
Replacing wheels and tires When replacing a tire, use the same size, tread design, speed rating and load carrying capacity as originally equipped. Recommended types and sizes are shown in “Wheels and tires” in the “Technical and consumer information” section of this manual.
If excessive tire wear is found, it is recommended that all four tires be replaced with tires of the same size, brand, construction and tread pattern. The tire pressure and wheel alignment should also be checked and corrected as necessary. Contact a NISSAN dealer. Wheel balance Unbalanced wheels may affect vehicle handling and tire life. Even with regular use, wheels can get out of balance. Therefore, they should be balanced as required. ● Do not use abrasive cleaners when washing the wheels.
MEMO 8-44 Maintenance and do-it-yourself
9 Technical and consumer information Capacities and recommended fuel/lubricants . . . . . . . . . 9-2 Fuel recommendation (without Flexible Fuel Vehicle option). . . . . . . . . . . . . . 9-3 Flexible fuel vehicle (FFV) fuel recommendation (if so equipped). . . . . . . . . . . . . . . . . 9-5 Engine oil and oil filter recommendations . . . . . . . . . . 9-6 Air conditioner system refrigerant and oil recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 Specifications. . . . . . .
CAPACITIES AND RECOMMENDED FUEL/LUBRICANTS The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Fuel Capacity (Approximate) US measure Imp measure 28 gal 23-1/4 gal Liter 105.8 Recommended Fluids and Lubricants 6-7/8 qt 6-1/2 qt 6.5 6.
FUEL RECOMMENDATION (without Flexible Fuel Vehicle option) Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). CAUTION ● Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85. ● Using a fuel other than that specified could adversely affect the emission control system, and may also affect the warranty coverage.
● E-15 fuel contains more than 10% oxygenate. E-15 fuel will adversely affect the emission control devices and systems of the vehicle and should not be used. Damage caused by such fuel is not covered by the NISSAN new vehicle limited warranty. ● If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corrosion inhibitors.
FLEXIBLE FUEL VEHICLE (FFV) FUEL RECOMMENDATION (if so equipped) Your vehicle is designed to use (E-85) Fuel Ethanol, “Regular” unleaded regular gasoline or any percentage of the two fuels combined. U.S. government regulations require Fuel Ethanol dispensing pumps to have a small, square, orange and black label with the common abbreviation or the appropriate percentage for that region. CAUTION CAUTION Only vehicles with the E-85 filler door label can operate on E-85.
Fuel consumption Because E-85 fuel contains less energy per gallon than gasoline, you will experience an increase in fuel consumption. You can expect your fuel mileage to decrease by about 30% compared to gasoline operation. Replacement parts Many components in your Flexible Fuel Vehicle (FFV) are designed to be compatible with ethanol. Always be sure that your vehicle is serviced with correct ethanol compatible parts.
Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important to select the engine oil viscosity based on the temperatures at which the vehicle will be operated before the next oil change. Choosing an oil viscosity other than that recommended could cause serious engine damage. Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high-quality genuine NISSAN oil filter.
SPECIFICATIONS ENGINE Model Type Cylinder arrangement Bore x Stroke Displacement Firing order VK56DE Gasoline, 4-cycle, DOHC 8-cylinder, V-block, Slanted at 90° in (mm) 3.858 x 3.622 (98 x 92) cu in (cm3) 338.78 (5,552) 1–8–7–3–6–5–4–2 Idle speed A/T (in “N” position) Ignition timing (degree B.T.D.C. at idle speed) CO % at idle Spark plug Spark plug gap (Nominal) Camshaft operation This spark ignition system complies with the Canadian standard ICES-002.
WHEELS AND TIRES DIMENSIONS AND WEIGHTS Wheels 18 x 8.0JJ 20 x 8.
WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY VEHICLE IDENTIFICATION When planning to drive your NISSAN vehicle in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your vehicle to areas where appropriate fuel is not available.
WTI0095 ENGINE SERIAL NUMBER The number is stamped on the engine as shown. WTI0099 WTI0189 F.M.V.S.S./C.M.V.S.S. CERTIFICATION LABEL EMISSION CONTROL INFORMATION LABEL The Federal/Canadian Motor Vehicle Safety Standard (F.M.V.S.S./C.M.V.S.S.) certification label is affixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number (VIN), etc. Review it carefully.
INSTALLING FRONT LICENSE PLATE WTI0100 WTI0220 LTI0093 TIRE AND LOADING INFORMATION LABEL AIR CONDITIONER SPECIFICATION LABEL Use the following steps to mount the front license plate: The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. The air conditioner specification label is affixed to the underside of the hood as shown. 1. Make holes on the plastic finisher at the location mark (small dimple) using a 0.20 in (5 mm) drill.
VEHICLE LOADING INFORMATION WARNING ● It is extremely dangerous to ride in a cargo area inside a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. ● Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. ● Be sure everyone in your vehicle is in a seat and using a seat belt properly.
Do not exceed the load limit of your vehicle shown as “The combined weight of occupants and cargo” on the Tire and Loading Information label. Do not exceed the number of occupants shown as “Seating Capacity” on the Tire and Loading Information label. To get “the combined weight of occupants and cargo”, add the weight of all occupants, then add the total luggage weight. Examples are shown in the following illustration.
Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX lbs or XXX kg” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX lbs or XXX kg. 4. The resulting figure equals the available amount of cargo and luggage load capacity. For example, if the XXX amount equals 1,400 lbs.
WARNING WARNING ● Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unsecured cargo could cause personal injury. ● Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts of your vehicle can break, tire damage could occur, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury.
Check the tightness of the tie-down cleat periodically during a trip to make sure the center bolt has not become loose. Install the tie-down cleat as follows: 1. Remove the channel protectors by sliding them out the back of the truck bed. Properly store the channel protectors. 2. Loosen the center bolt completely. LTI0103 3. Insert the cleat into the channel perpendicular to the channel as shown. Then rotate the cleat clockwise 90° and slide it to the desired location. LTI0104 4.
WTI0124 5. There should be no gap between the bottom of the cleat and the top of the channel. Tighten the center bolt hand tight (20-40 in-lbs ).
LTI0106 CAUTION ● Install only one cleat per section of channel. ● Applying loads at angles to the cleats greater then 45° or loads greater than 150 lbs. (header and floor channels) or 200 lbs. (side channels) may cause damage to the channel or bed.
LTI0123 1 correct installation, 2 incorrect installation WARNING Do not install accessories over the gap between the front and rear side channels. Doing this could affect the rear structure in certain rear impacts, which could result in serious injury. WTI0119 CAUTION Properly secure all cargo with ropes or straps to prevent it from sliding or shifting. Use the channel end stoppers to help secure items in the channels from sliding off the end of the truck bed.
Install the channels end stoppers as follows: 1. Remove the channel protectors by sliding them out the back of the truck bed. Properly store the channel protectors. 2. Loosen the bolt on the center of the end stopper with the provided wrench and insert it into the channel. 3. Position the end stopper to the desired location on the channel so the nubs on the bottom of the end stopper fully seat into the channel detents. 4. Tighten the bolt on the center of the end stopper with the provided wrench.
TRUCK-CAMPER LOADING INFORMATION CREW CAB MODELS WARNING Crew Cab short wheel base models should not be used to carry a slide-in camper. Improper loading may be dangerous. If a load is too far back, it can affect handling characteristics. If a load is too far forward, the front axle may be overloaded. KING CAB MODELS This information is provided for you to properly install a slide-in camper and is based on the National Highway Traffic Safety Administration regulations.
MEASUREMENT OF WEIGHTS WARNING Overloading or improper loading can adversely affect vehicle handling, braking and performance and may lead to accidents.
TOWING A TRAILER WARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and performance and may lead to accidents. CAUTION ● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km). Your engine, axle or other parts could be damaged. ● For the first 500 miles (800 km) that you tow a trailer, do not drive over 50 mph (80 km/h) and do not make starts at full throttle.
Temperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automatically decrease engine power. Vehicle speed may decrease under high load. Plan your trip carefully to account for trailer and vehicle load, weather and road conditions.
Towing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load. The vehicle and trailer need to be weighed to confirm the vehicle is within the GVWR, Front GAWR, Rear GAWR, Gross Combined Weight Rating (GCWR) and Towing capacity.
Example: ● Gross Vehicle Weight (GVW) as weighed on a scale - including passengers, cargo and hitch - 6,200 lb. (2,812 kg). ● Gross Vehicle Weight Rating (GVWR) from F.M.V.S.S./C.M.V.S.S. certification label 7,100 lb. (3,220 kg). ● Gross Combined Weight Rating (GCWR) from “Towing Load/Specification⬙ chart 15,100 lb. (6,848 kg). ● Maximum Trailer towing capacity from “Towing Load/Specification⬙ chart - 9,200 lb. (4,173 kg). 7,100 lb. (3,220 kg) – 6,200 lb. (2,812 kg) = 900 lb.
TOWING LOAD/SPECIFICATION Towing load specification chart with tow package — short wheel base 2WD Maximum Towing Capacity *1, *2, *3 Maximum Tongue load *2, *3 Maximum King pin load Maximum Gross Combined Weight Rating KC SV 9,500 lb. (4,309 kg) 950 lb. (431 kg) 1,425 lb. (646 kg) 15,100 lb. (6,848 kg) 4WD CC SV 9,400 lb. (4,263 kg) 940 lb. (426 kg) 1,410 lb. (639 kg) 15,100 lb. (6,848 kg) KC SL 9,200 lb. (4,173 kg) 920 lb. (417 kg) 1,380 lb. (626 kg) 15,100 lb. (6,848 kg) SV 9,400 lb.
Towing load specification chart without tow package — short wheel base 2WD KC Maximum Towing capacity*1, *2, *3 Maximum Tongue load *2, *3 Maximum King pin load Maximum Gross Combined Weight Rating S 7,400 lb. (3,356 kg) 740 lb. (336 kg) 1,110 lb. (504 kg) 12,800 lb. (5,806 kg) SV 7,400 lb. (3,356 kg) 740 lb. (336 kg) 1,110 lb. (504 kg) 12,800 lb. (5,806 kg) S 7,400 lb. (3,356 kg) 740 lb. (336 kg) 1,110 lb. (504 kg) 12,800 lb. (5,806 kg) 4WD CC SV 7,400 lb. (3,356 kg) 740 lb. (336 kg) 1,110 lb.
TOWING SAFETY Trailer hitch Your vehicle may be equipped with an optional trailer tow package. The trailer tow package includes a receiver-type frame mounted hitch. This hitch is rated for the maximum towing capacity of this vehicle when the proper towing equipment is used. Choose a proper ball mount and hitch ball that is rated for the trailer to be towed. Genuine NISSAN ball mounts and hitch balls are available from your NISSAN dealer.
Weight distribution hitch General set-up instructions are as follows: This type of hitch is also called a “load-leveling” or “equalizing” hitch. A set of bars attach to the ball mount and to the trailer to distribute the tongue weight (hitch weight) of your trailer. Many vehicles can’t carry the full tongue weight of a given trailer, and need some of the tongue weight transferred through the frame and pushing down on the front wheels. This gives stability to the tow vehicle.
Sway control device Class IV hitch Sudden maneuvers, wind gusts, and buffeting caused by other vehicles can affect trailer handling. Sway control devices may be used to help control these affects. If you choose to use one, contact a reputable trailer hitch supplier to make sure the sway control device will work with the vehicle, hitch, trailer and the trailer’s brake system. Follow the instructions provided by the manufacturer for installing and using the sway control device.
● Regularly check that all trailer hitch mounting bolts are securely mounted. ● When towing with the hitch ball mounted to the rear bumper, do not make sharp turns. The trailer may contact the bumper and cause damage to the bumper or trailer. ● When towing a 5th wheel trailer, do not make sharp turns while driving or backing. The trailer may contact the vehicle and cause damage to both the trailer and vehicle.
Electric Trailer Brakes - Electric braking systems are activated by an electronic signal sent from a trailer brake controller (special brakesensing module). If electric trailer brakes are used, see “Electric trailer brake controller” in this section. To install the electric trailer brake controller jumper harness, perform the following procedure: 1. Open the driver door. Move the seat to the rearmost position.
Wire color designation for electric trailer brake controller jumper harness. WIRE COLOR RED/GREEN BLACK BROWN/WHITE RED/BLUE RED LTI0118 LTI0115 2. Apply the parking brake to access the jumper harness connector. 3. Locate the jumper harness connector under the lower portion of the instrument panel. The connector is taped to the wiring harness 1 as indicated. 䊊 NOTE Vehicle stop lamp switch to trailer brake controller. Brake controller ground (-). Trailer brake controller switched output.
Pre-towing tips ● Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched. Do not drive the vehicle if it has an abnormal nose-up or nose-down condition; check for improper tongue load, overload, worn suspension or other possible causes of either condition. ● Always secure items in the trailer to prevent load shift while driving. LTI0116 4. Peel off the tape and connect the jumper 2 . harness to the connector 䊊 5. Release the parking brake. 6.
Always block the wheels on both vehicle and trailer when parking. Parking on a slope is not recommended; however, if you must do so: CAUTION If you move the shift selector to the P (Park) position before blocking the wheels and applying the parking brake, transmission damage could occur. 7. Turn off the engine. 1. Start the vehicle. 2. Have someone place blocks on the downhill side of the vehicle and trailer wheels. 4. Release the parking brake. 5. Shift the transmission into P (Park).
Do the following if the trailer begins to sway: 1. Take your foot off the accelerator pedal to allow the vehicle to coast and steer as straight ahead as the road conditions allow. This combination will help stabilize the vehicle – Do not correct trailer sway by steering or applying the brakes. 2. When the trailer sway stops, gently apply the brakes and pull to the side of the road in a safe area. 3. Try to rearrange the trailer load so it is balanced as described earlier in this section.
SNOW PLOW FLAT TOWING UNIFORM TIRE QUALITY GRADING WARNING Towing your vehicle with all four wheels on the ground is sometimes called flat towing. This method is sometimes used when towing a vehicle behind a recreational vehicle, such as a motor home. CAUTION ● Failure to follow these guidelines can result in severe transmission damage. ● Whenever flat towing your vehicle, always tow forward, never backward.
EMISSION CONTROL SYSTEM WARRANTY WARNING The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics. Temperature A, B and C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat, and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
REPORTING SAFETY DEFECTS For USA If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying NISSAN. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
READINESS FOR INSPECTION/ MAINTENANCE (I/M) TEST EVENT DATA RECORDERS (EDR) Due to legal requirements in some states and Canadian Provinces, your vehicle may be required to be in what is called the “ready condition” for an Inspection/Maintenance (I/M) test of the emission control system. This vehicle is equipped with an Event Data Recorder (EDR).
OWNER’S MANUAL/SERVICE MANUAL ORDER INFORMATION Genuine NISSAN Service Manuals for this model year and prior can be purchased. A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle. This manual is the same one used by the factorytrained technicians working at NISSAN dealerships. Genuine NISSAN Owner’s Manuals can also be purchased. For USA For current pricing and availability of genuine NISSAN Service Manuals, contact: 1-800-450-9491 www.nissan-techinfo.
MEMO 9-44 Technical and consumer information
10 Index 4WD warning light . . . . . . . . . . . . . . .2-16 A Active brake limited slip (ABLS) system . . .5-34 Adjusting pedal position . . . . . . . . . . . .3-14 Air bag (See supplemental restraint system) . . . . . . . . . . . . . . . . . . . . .1-47 Air bag system Front (See supplemental front impact air bag system) . . . . . . . . . . . . . . .1-54 Air bag warning labels . . . . . . . . . . . . .1-61 Air bag warning light. . . . . . . . . . .1-62, 2-18 Air cleaner housing filter . . . . . . . . . . .
Check tire pressure . . . . . . . . . . . . . . .2-25 Child restraints . . . . . . .1-24, 1-25, 1-26, 1-28 Precautions on child restraints. . . . . . . . .1-26, 1-32, 1-36, 1-43 Top tether strap anchor point locations . .1-30 Child safety rear door lock . . . . . . . . . . . .3-7 Chimes, audible reminders . . . . . . . . . . .2-20 Cleaning exterior and interior . . . . . . . . . . .7-2 Clock . . . . . . . . . . . . . . . . . . . . . . .4-44 C.M.V.S.S. certification label . . . . . . . . . .
Fuel Capacities and recommended fuel/lubricants . . . . . . . . . . . . . . . . .9-2 Fuel economy . . . . . . . . . . . . . . . .5-23 Fuel-filler door and cap . . . . . . . . . . .3-12 Fuel gauge . . . . . . . . . . . . . . . . . . .2-7 Fuel octane rating . . . . . . . . . . . . . . .9-4 Fuel recommendation . . . . . . . . . . . . .9-3 Loose fuel cap warning. . . . . . . .2-24, 3-12 Fuses . . . . . . . . . . . . . . . . . . . . . . .8-22 Fusible links . . . . . . . . . . . . . . . . . . .
Bulb check/instrument panel . . . . . . . .2-13 Bulb replacement . . . . . . . . . . . . . .8-29 Charge warning light . . . . . . . . . . . .2-15 Fog light switch . . . . . . . . . . . . . . .2-33 Headlight and turn signal switch . . . . . .2-30 Headlight control switch . . . . . . . . . .2-30 Headlights . . . . . . . . . . . . . . . . . .8-27 Interior light. . . . . . . . . . . . . . . . . .2-56 Light bulbs . . . . . . . . . . . . . . . . . .8-27 Low tire pressure warning light . . . . . . .
On-pavement and off-road driving precautions . . . . . . . . . . . . . . . . . .5-3 Precautions on child restraints. . . . . . . . .1-26, 1-32, 1-36, 1-43 Precautions on seat belt usage . . . . . . .1-15 Precautions on supplemental restraint system . . . . . . . . . . . . . . . . . . . .1-47 Precautions when starting and driving . . . .5-2 Pre-tensioner seat belt system . . . . . . . . .1-60 Programmable features . . . . . . . . . . . . . .4-7 Push starting . . . . . . . . . . . . . . . . . . .
Sunglasses case. . . . . . . . . . . . . . . . .2-45 Sunroof . . . . . . . . . . . . . . . . . . . . . .2-54 Sunroof (see Moonroof) . . . . . . . . . . . . .2-54 Sun visors . . . . . . . . . . . . . . . . . . . .3-15 Supplemental air bag warning labels . . . . . .1-61 Supplemental air bag warning light . . .1-62, 2-18 Supplemental front impact air bag system . . .1-54 Supplemental restraint system Information and warning labels . . . . . . .1-61 Precautions on supplemental restraint system . . . . . . . . .
Vehicle security system (NISSAN vehicle immobilizer system), engine start. .2-26, 3-2, 5-11 Ventilators . . . . . . . . . . . . . . . . . . . .4-17 Visors . . . . . . . . . . . . . . . . . . . . . . .3-15 Voice recognition system . . . . . . . . . . .4-119 Voltmeter . . . . . . . . . . . . . . . . . . . . . .2-8 W Warning 4WD warning light. . . . . . . . . . . . . .2-16 Air bag warning light . . . . . . . . .1-62, 2-18 Anti-lock brake warning light . . . . .2-13, 2-14 Battery charge warning light . . . . .
GAS STATION INFORMATION RECOMMENDED FUEL (without Flexible Fuel Vehicle [FFV] option): Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) number (Research octane number 91). CAUTION ● Only vehicles with the E-85 filler door label can operate on E-85. Fuel system or other damage can occur if E-85 is used in vehicles that are not designed to run on E-85.
RECOMMENDED NEW VEHICLE BREAK-IN PROCEDURE: During the first 1,200 mi (2,000 km) of vehicle use, follow the recommendations outlined in the “Break-in schedule” information found in the “Starting and driving” section of this manual. Follow these recommendations for the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in vehicle damage or shortened engine life.
2014 NISSAN TITAN ® 2014 TITAN OWNER’S MANUAL A60-D A60-D Printing : September 2013 (19) 0A60U0 OM14E0A60U0 Publication No.: OM1E Printed in U.S.A. For your safety, read carefully and keep in this vehicle.
