Owner manual

ManualsBrandsNitek ManualsHardwareEL1500UW

NITEK ®

De Schans 19-21 2a

8231 KA Lelystad

Tel: +31(0)320-230005

E-mail: info@nitek.nl

WWW.NITEK.NL

USA

5410 Newport Drive, # 24

Rolling Meadows, IL 60008

Phone: (847) 259-8900

Fax: (847) 259-1300

E-mail: info@nitek.net

WWW.NITEK.NET

EUROPE

INSTALLATION GUIDE

EL1500UW

Outdoor IP Video Camera Over UTP

Ethernet Extender & PoE Injector with EtherStretch

Description

The EL1500UW is another component of the NITEK EtherStretch line. Our EtherStretch solution

allows for the utilization of existing cable infrastructure (coax or UTP) to transmit data from IP cam-

eras and other network devices along with power (PoE) to operate these networked devices well be-

yond standard network limitations. The system can extend Ethernet to over 600m or 2000ft of UTP

cable making the EL1500UW is ideal for retrofitting existing installations.

The EL1500UW system consists of a NEMA4 weatherproof case enclosed transmitter and a receiver

unit that require very little installation time and absolutely no set up or configuration. The system al-

low CAT5e and CAT6 cables to be used well beyond traditional limits. The EL1500UW can com-

municate at 100Mb to distances over 600m or 2000ft. It can also turn these cables into PoE pathway

to power and operate IP cameras.

The EL1500UW is completely transparent to the network thus requiring no IP and MAC addressing.

Simply connect your network devices to the networking ports of the transmitter and receiver along

with existing cabling and the system begins communicating. LED indicators show the status and

speed of network communications and PoE power.

The NITEK EtherStretch EL1500UW reliably extends network communications to overcome cable

distance limitations offering connectivity to devices in locations traditional networking does not allow.

The units are constructed of industrial grade RoHS compliant plated aluminum with a corrosion

resistant finish and with the addition of the NEMA4 enclosure makes them extremely durable.

IEC/UL 60950-1

Patent Pending

11012013

Summary of content (9 pages)

PAGE 1
INSTALLATION GUIDE EL1500UW Outdoor IP Video Camera Over UTP Ethernet Extender & PoE Injector with EtherStretch Description The EL1500UW is another component of the NITEK EtherStretch line. Our EtherStretch solution allows for the utilization of existing cable infrastructure (coax or UTP) to transmit data from IP cameras and other network devices along with power (PoE) to operate these networked devices well beyond standard network limitations.
PAGE 2
Important Safety Instructions Read all Safety Instructions. Keep the Instructions for future reference. Be sure to HEED all Warnings. Follow ALL instructions. DO NOT use this device or any of the equipment described, near water. Clean this device ONLY with a dry cloth. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions. DO NOT install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
PAGE 3
Parts of the EL1500UW LINK PORT SIDE NETWORK PORT SIDE Installation Considerations Wire and Cable Recommendations: The EL1500CW is designed to use with ANSI/TIA/EIA defined CAT5e or CAT6 Unshielded Twisted Pair (UTP) cabling. This UTP cable shall be able to accommodate TCP/IP data operating speeds of 10/100 Mbps transmission rates. The RJ45 termination pin out schemes shall be in accordance with the 568B standard. The quality of which must be consistent with any reasonably serviceable cable condition.
PAGE 4
Installation & Setup Equipment Requirements & Mounting: The process for utilizing the EL1500UW is rather quick and easy. A common topology involves a length of existing or new UTP (CAT5e/CAT6) cable (up to but not exceeding 2000ft/600m), the NEMA4 enclosed EL1500U transmitter and receiver, an IP camera or other peripheral network device (both universally referred to as the Power Device or PD), and a 3rd party PoE network switch (or Power Sourcing Equipment/PSE). The PD and PSE must both be either 802.
PAGE 5
Installation & Setup Equipment Requirements & Mounting: The process for utilizing the EL1500UW is rather quick and easy. Another common topology involves a length of existing UTP (CAT5e/CAT6) cable (up to but not exceeding 2000ft/600m), the NEMA4 enclosed EL1500U transmitter and a receiver (ER1500U), an IP camera or other peripheral network device, a NITEK (IP1054) or 3rd party PoE injector/inserter or Power Sourcing Equipment/ PSE, and finally a network switch. The Camera and PSE must be either 802.
PAGE 6
Device Dimensions NEMA4 Enclosure 6.732 0.591 4.764 Top (Side View) NITEK Top (Inside View) 6.732 Top (Outside View) Transmitter/Receiver 3.6" 1.1" 1.6" Optional Power Input, Class 2 48 to 56VDC, 800mA NITEK Link Status EL1500U 10/100 Link Port POE Out Network Port Power Made in USA 4.288 3.602 Right TOP Left Bottom 1.6" Bottom (Inside View) 6.260 Bottom (Outside View) 1.1" 7.125 1.640 Bottom (Side View) 7.125 568B Pin out Termination 4.
PAGE 7
Connectivity Status NETWORK PORT LINK PORT LED INDICATORS Connector Network Port LED OFF ON Power No power Power Good Link Status No Ethernet Link Ethernet Link Good PoE Out No PoE Power Out PoE Power Good 10/100 No Link 100Mb Link Port FLASHING 10Mb PoE Distance Chart Available PoE Wattage At PoE Device 30.0 29.2 27.1 25.2 25.0 Watts 20.3 20.0 15.0 16.8 15.4 15.4 15.4 13.7 11.1 10.0 0.0 802.3AT 802.
PAGE 8
Troubleshooting PROBLEM POSSIBLE CAUSE No video/data Check camera and EL1500UW device connections. Check UTP cable condition and RJ45 connectors. Check that the camera is powered. Check that supplied camera power meets manufacturer’s specifications. Check that UTP cable distance does not exceed PoE capabilities. Refer to chart on pg 7. Check that UTP cable does not exceed the EL1500UW’s operating distances. Check link & device status. See chart on pg 7.
PAGE 9
Product Warranty and Return Information Lifetime Limited Warranty Network Extender Products NITEK warrants the original consumer purchaser that the Network Extender products that it sells will be free from defects in material and workmanship. If any such product proves defective by our inspection, after sale to the original consumer purchaser, NITEK, at its option, will either repair the defective product without charge for parts and labor or will provide a replacement in exchange for the defective product.