CafeRomatica Fully automatic coffee centre Operating Instructions and Useful Tips Neue Lust auf Kaffee. NICR7..
NICR7..
Equipment A Text display screen with control keys B Removable water reservoir C Cupwarming / holding plate D Water quantity control knob E Coffee strength button F 1-cup button G 2-cup button H On / Off button I Service button ‘S’ J Height-adjustable coffee spout K Cup-warming function (On / Off switch, NICR770 only) L Nameplate with model name M Grinder settings control knob (inside) N Bean container with lid O Pre-ground coffee chamber P Steam warm-up button Q Steam / hot water
Equipment 2 3 4 5 6 7 8 9 10 11 f b a b c d e f Control knob Air inlet valve Air inlet pipe Inlet valve Steam / hot water jet Liquid inlet hose c d a e
Operating Instructions and Useful Tips Dear Customer, Congratulations and many thanks for choosing a high-quality NIVONA product. To get the most out of your NIVONA machine, please read this manual carefully before use. Please start by reading the safety notes. Please keep this manual in a safe place. You may want to use it as reference guide or hand it on to any further users of your machine.
Contents 1. Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 2. Set up . . . . . . . . . . . . . . . . 2.1 Preparing the machine . 2.2 Getting started . . . . . . . 2.3 Grinder settings . . . . . . 2.4 Cup-warming function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. Safety instructions • This machine may only be used for the intended purpose (domestic use) and is not for commercial application – see guarantee conditions. Otherwise, claims under the guarantee will not be accepted. • Operating voltage must be the same as mains voltage. Please note the model nameplate / sticker on the machine (fig. 1/L). • Do not operate the machine if the power cord or machine case is damaged. • Keep the power cord away from hot parts.
... 1. Safety instructions similarly qualified specialist, in order to avoid any hazards. Caution: Electrical appliances must be repaired by qualified personnel. Non-professional repairs can expose the user to significant dangers. Liability for damages cannot be accepted if the machine is used for any other than the intended purpose, incorrectly maintained or serviced. Caution: Using the on/off button (fig. 1/H) during brewing can damage the machine.
... 2. Set up 2.2 Getting started ➔ Remove the plug from the power cord compartment (fig. 1/V) and plug the machine in. ➔ Press the On / Off button (fig. 1/H). „SYSTEM HEIZT“ (“SYSTEM IS HEATING”) appears in the display (*otherwise, please see the following Note below). ➔ After the machine has warmed up, the service button (fig. 1/I) flashes. The instruction „BITTE SPÜLEN“ (“PLEASE RINSE”) flashes in the display. ➔ Now place a cup under the heightadjustable coffee spout (fig.
... 2. Set up The cup-warming function can be switched off by pressing the “cupwarming” On / Off button (fig. 1/K and 10) a second time. Use the warming function to optimise the temperature and aroma of your coffee to suit your personal preference. The light in the switch indicates whether the warming function is switched on or off. 3. Making coffee Note: The machine is preset for immediate use. However, we recommend that first you adjust the most important settings to suit your personal preferences.
... 3. Making coffee 3.2 Selecting water quantity You can freely select the quantity of water used by turning the water quantity control knob (fig. 1/D and 6), (the empty cup bottom left represents less water, the full cup bottom right represents more water). ➔ The selected quantity of water is displayed in the upper line of the display screen. ➔ Water quantity can be adjusted in 10ml steps from 20ml to 240ml by turning the water quantity control knob from left to right.
... 3. Making coffee ➔ Press the 2-cup button (fig. 1/G). ➔ The machine now starts the grinding and brewing operation and produces two consecutive cups of coffee. chamber, and use only fresh or vacuumpacked coffee ground from beans. Do not add instant coffee powder! 3.6 Drawing hot water Note: · The brewing operation can be stopped at any point by pressing the 1-cup (fig. 1/F) or 2-cup buttons (fig. 1/G).
... 3. Making coffee Note: Steam can be drawn for about 2 minutes. Then the machine will automatically switch the operation off. You can prolong the operation by turning the control knob (fig. 1/Q and 7) back and forth. Caution: Risk of scalding! The steam which comes out is very hot. Only touch the black plastic parts of the jet. It is hard to remove dried milk left on the jet after frothing.
4. Programming functions The function keys under the text display screen are used to program functions (fig. 1/A and 4): P > ok exit = = = = Programming mode Selection key Confirmation key Cancel or end programming Important: Please note that you can only program functions if the On / Off button (fig. 1/H) is switched to ON (display lit up).
... 4. Programming functions reservoir using the assembly tool on the end of the measuring spoon. ➔ Fill up the reservoir with fresh water and put it back in the machine. ➔ Hold a container under the steam / hot water jet (fig. 1/T) and turn the control knob (fig. 1/Q and 7) to the right to open. The system will now be rinsed out. ➔ Wait until no more water comes out of the jet for a short time and turn the control knob (fig. 1/Q and 7) back to the left to close.
... 4. Programming functions First, test your water with the test strips provided: MUM” as desired. The default setting is “HIGH”: ➔ Dip the strip into the water and then shake it lightly off. ➔ After about a minute you can read the result by counting the red dots on the test strip. ➔ The settings corresponding to the different levels of hardness are as follows: ➔ Press the program key P to enter programming mode. ➔ Press the > key until “PROGRAM TEMPERATURE” appears. ➔ Press the ok key.
... 4. Programming functions 4.6 Language You can set 14 different languages: German, English, French, Italian, Dutch, Polish, Russian, Estonian, Czech, Swedish, Danish, Lithuanian, Hungarian and Turkish. The default setting is German. ➔ Press the program key P to enter programming mode. ➔ Press the > key until “WÄHLE SPRACHE” (“SELECT LANGUAGE”) appears ➔ Press the ok key. ➔ Press the > key until your desired language appears. ➔ Confirm your selection by pressing ok. The display reads “SELECT LANGUAGE”.
... 4. Programming functions remains on power-saving ECO Mode with minimal heat output 3 minutes after its last use – therefore using less electricity. If the coffee maker is started from power-saving ECO Mode, this can take a few seconds longer (heating time). You can also deactivate the ECO Mode, so that the appliance is on full stand-by while switched on: ➔ Press the program key P to enter programming mode. ➔ Press the > key until “PROGRAM ECO-MODE” appears. ➔ Press the ok key.
... 5. Maintenance and Care replace it in the machine. ➔ Press the program key P to enter programming mode. ➔ Press the > key until “PROGRAM FILTER” appears. ➔ Press the ok key. The display reads “FILTER YES”. ➔ Press the ok key again. The display reads “MANUAL CHANGE FILTER”. ➔ Press the ok key to confirm. ➔ “CHANGE FILTER” and “TURN VALVE” appear alternately in the display. ➔ Hold a container under the steam / hot water jet (fig. 1/T) and turn the control knob (fig. 1/Q and 7) to the right to open.
... 5. Maintenance and Care ➔ Press the program key P to enter programming mode. ➔ Press the > key until “SELECT CLEANING” appears. ➔ Press the ‘ok’ key. The display reads “MANUAL CLEANING” ➔ Press the ok key. “EMPTY TRAYS” appears alternately with “FILL WATER” in the display. ➔ Continue as described above, from Point 5.3, ‘Remove the drip tray … 5.4 Descaling Note: When the machine needs descaling, the message “PLEASE DESCALE” appears in the display and the service button (fig. 1/I) flashes.
... 5. Maintenance and Care ➔ The system is rinsed out in intervals once more through the steam / hot water jet (fig. 1/T) (about 5 mins.). ➔ As soon “TURN VALVE” appears in the display, you can turn the valve control knob (fig. 1/Q and 7) back to the left to close. ➔ The system is rinsed out at intervals through the inside spout (about 5 minutes). ➔ As soon as the rinse is completed, “EMPTY TRAYS” appears in the display. ➔ Empty the drip tray (fig. 1/Z) and replace it in the machine.
... 5. Maintenance and Care ➔ Then extract the brewing unit carefully by the handle (fig. 9). ➔ Wash the brewing unit under running water and then let it dry. ➔ Replace and lock the brewing unit with equal care by pressing the red lever switch and turning the handle to the right until it clicks. ➔ Replace the cover and screw the screws back in. FROM MODEL NICR 750 ONLY: Your appliance is equipped with moveable rear rollers (see image 1/S). This allows it to be moved easily on a level worktop.
... 6. System messages Message ➔ Meaning ➔ What to do TRAYS MISSING ➔ Drip tray (fig. 1/Z) and used coffee tray (fig. 1/U) are absent or not correctly positioned ➔ Contacts on back of drip tray are not clean ➔ Position water and used coffee trays correctly SYSTEM IS TOO HOT ➔ Machine is overheating ➔ Cool machine by drawing hot water (see 3.6) PLEASE CLEAN ➔ Cleaning is needed ➔ Clean machine (see 5.3) PLEASE DESCALE ➔ Descaling is needed ➔ Descale the machine (see 5.
7. Troubleshooting Fault ➔ Meaning ➔ What to do No hot water / steam comes out of jet ➔ Jet (fig. 1/T) is blocked ➔ The system may have a build-up of limescale ➔ Clean jet thoroughly Too little milk foam or foam too liquid ➔ Unsuitable milk ➔ Jet is blocked ➔ Use cold milk ➔ Take jet apart and clean (see fig. 11) ➔ Please use a large dose of descaler (see 5.4) ➔ Contact service ➔ The system may have a build-up of limescale ➔ Air inlet valve incomplete (see fig.
8. Further instructions Professional care and maintenance Your love of coffee is here to stay. The CLARIS filter cartridge NIRF 700 is filled with purely organic material, without chemical additives, if changed regularly, it ensures that you will have to descale your NIVONA machine less often. Cleaning tablets NIRT 700 Your fully automatic coffee centre provides an integrated cleaning programme.
... 8. Further instructions Transport and storage Protecting the environment The steam must be evacuated from the machine if it is to be transported or stored in cold rooms. Electric and electronic appliances often contain valuable or harmful materials which should not be processed in the same way as normal household waste. If incorrectly processed, they can harm human health and the environment. Please therefore do not put your machine in the dustbin with normal waste.
56 56