Fusion HD Quick Start Guide Nixeus Technology, Inc. Version 1.
About This Guide This Quick Start Guide gives you the information for you to setup your unit and enjoy viewing your multimedia files. The user manual will describe the unit in more detail. Please go to www.nixeus.com to download it. For quick help, press the “ ” button on the remote control. (This key function will be supported later through firmware upgrade.) Nixeus Technology, Inc.
Safety Information WARNING: Failure to follow these safety instructions could result in fire, electric shock, or other injury or damage. Read these instructions Keep these instructions Heed all Warnings Follow all instructions Do not use this apparatus near water. Clean only with dry cloth. Do not install near any hear sources such as radiators, stoves, or other apparatus (including amplifiers) that produce heat.
CAUTION: About Laser and LED Use of controls or adjustments, or performance of procedures other than those specified herein may result in hazardous radiation exposure. This device complies with International Standard IEC 60825-1:2001-08 for a Class 1 and Class 2 laser product. This device also complies with 21CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001.
Package Contents The product package should contain the following items: • • • • • • • • • • Fusion HD media player Remote Control/AAA batteries * 2 USB Wi-Fi Dongle 12V/2.5A Power supply Mini USB to A type USB cable HDD SATA Data and power cable (attached in the box) AV phone jack to RCA cable LAN Cable 4 screws for mounting HDD Quick Start Guide WARNING: Ensure you use the power adapter shipped with the unit. Other power adapters may damage or even destroy the unit. Nixeus Technology, Inc.
Hardware Overview Front View 1 ○ 3 ○ 4 ○ 5 ○ 7 ○ 8 ○ 6 ○ No# 1 ○ Front Panel Description Power on/Standby LED “Red”: ● The power supply is attached but the device has not been powered on yet or the device has been powered off after use. “Orange” ●: The device is in stand by or in the process of turning on. “Green” ●The device is operating. 3 ○ Remote control LED 4 ○ Remote sensor 5 ○ eSATA port 6 ○ USB host port 7 ○ USB client port 8 ○ Power On /Off button Nixeus Technology, Inc.
Rear View 1 ○ 2 ○ 3 ○ 4 ○ 5 ○ No# 1 ○ Rear Panel Description 2 ○ LAN 3 ○ USB host port 4 ○ S/PDIF Optical connector 5 ○ S/PDIF Coaxial connector 6 ○ A/V Phone Jack 7 ○ HDMI port 6 ○ 7 ○ Power Adaptor Standby Mode: When you press the Power key on the remote control or the On/Off button on the unit, the system will enter standby mode.
Installation and Connection Video & Audio The HDMI port is used for connecting your unit to your TV so you can view high-definition video and audio. The Optical and Coaxial S/PDIF connections are for connecting your unit to an external decoder or amplifier for high definition audio. Press the hotkey button on the remote control and go to ‘System Setup’ → ‘Audio Setup’ to select Analog or Digital Audio Output.
Storage Devices The eSATA port is for connecting the unit to your PC so that you can copy files from your PC to the device. eSATA connections are faster than the USB client ports on the device. The USB client port is another option for you to connect the unit to your PC and copy files from your PC to the unit. The USB host port can be used to connect external HDD enclosures, flash drives, Wi-Fi Dongles, Mice or keyboards to the unit.
HDD Installation To install a HDD into your unit, follow the instructions below. 1. Use a screwdriver to remove the screws on the device. 2. Carefully remove the top cover. 3. Fit the HDD in as shown below. Nixeus Technology, Inc.
4. Connect the power/data cable to the HDD. 5. Using a screwdriver, secure the HDD to the unit with the 4 screws provided. 6. Refit the cover back onto the unit and secure in place with the screws previously removed. Nixeus Technology, Inc.
Remote Control The remote control is used to navigate menus and to select and watch videos, listen to music, or view photos on your TV. Please refer to the user manual for full details on each of the buttons. Nixeus Technology, Inc.
1 2 3 5 4 8 11 10 12 14 13 37 16 17 15 18 19 20 22 21 23 24 27 25 26 28 30 31 33 29 32 34 36 35 Nixeus Technology, Inc.
The table below lists the button functions of the remote control. REMOTE CONTROL KEY FUNCTION TABLE No. 1 2 3 4 5 KEYPAD POWER HOME OUTPUT HELP SETUP 8 BGM 10 COPY 11 MUTE 12 NUMBERS 13 PREV 14 NEXT 15 BACK 16 17 18 19, 20 INFO VOLUME ─ VOLUME ┼ 1. Skip to the previous page when browsing media files. 2. Skip to the previous file when playing media files. 1. Skip to the next page when browsing media files. 2. Skip to the next file when playing media files. 1. Return to previous page.
TV Mode Setup Please set the video source selector of your TV to match the connection to your unit. For example, if you use HDMI, set the TV to use the correct HDMI input port. 1. Turn on the unit. The LED on the front panel of the PowerZest will turn orange during system loading and then green when it’s ready. START-UP PAGE 2. Check the TV display by going to ‘Setup’ → ‘System Setup’ → ‘TV Mode Setup‘ → ‘Video Output’. The default display of the unit is Composite (CVBS).
Networking An example of a network with peripheral devices attached is below. NETWORK DIAGRAM Wired Network Setup 1. Press the “Setup” hotkey on the remote control or select “SETUP” mode from the Main Menu. Nixeus Technology, Inc.
2. Select “Network Setup” to configure and make changes to your network settings. 3. Once in “Network Setup”, Select “IP Setup”, and Enable DHCP or set your static IP address according to your network settings. Nixeus Technology, Inc.
Wireless Network Setup The unit supports wireless networking with a USB Wi-Fi dongle supplied with your unit. To enable wireless function, please make sure you plug the Wi-Fi dongle into the USB port before powering on the unit. Please note that a USB Wi-Fi dongle not supplied with the unit may NOT be supported. For high-definition video streaming a wired Ethernet connection between the unit and your network is recommended. Playback of normal video (eg.
2. Select “Network Wizard” from setup main menu to start the setup wizard. 3. Once the wizard has started, choose the “Wireless” option. 4. Select to look for all the available wireless networks and choose the one you wish to use. Nixeus Technology, Inc.
5. If the network you choose is locked by password, a “Lock” icon will be shown. And the signal strength is indicated by the red (poor quality), yellow (fair quality) or green (good quality) light. 6. Select “Key Value”, and have your password ready to enter. 7. The Key Length of each Key Format is described in the table below. For WPA and WPA2 format, the unit will detect and switch automatically.
8. Input your password and choose “Enter” to save. UPnP Servers The unit will automatically detect all available UPnP AV compliant content servers on boot-up and list them on the UPnP column of the main menu. No additional setup is necessary. TM TVersity is a popular and free UPnP server software. Please refer to http://tversity.com for more information and to download the software. Nixeus Technology, Inc.
Network Shared Folders (Samba Client) The Samba Client protocol allows the Fusion HD to access media files from samba shares on windows based PCs on the network As long as there is a connection to your network and there are no firewalls blocking the shares from remote sites, there are no additional steps needed to enable this feature. The following steps show how to access media through the Samba Client Protocol. 1.
3. Press the “MENU” button on the remote control to go to the ‘directory’ bar on the top of the screen. 4. Pressing the numerical buttons on the remote control during navigation will sort the file names by the first letter of the key pressed. This will help you find the file you want when there are many files in the folder list.
File Management by Remote Control 1. Go to “Removable Device” on the Main Page. 2. Select the name of your storage device from the list and press “COPY”. 3. Select the source and destination then Press “OK” to proceed or “No” to go back. Nixeus Technology, Inc.
Copy/Delete local files from your PC The unit supports Samba server function which shares your local storage space with a client PC over the network. For PC with a Windows OS installed it is known as My Network Places. To access your unit, type in the IP address of your unit (which you can find by checking in ‘Setup’) onto the address bar of the file manager on the remote PC and press the enter key to continue. The default user name and password to login are both “admin”.
2. Click “Entire Network” → “Workgroup” Nixeus Technology, Inc.
3. The units default local network location is “Workgroup”. Double click “Workgroup” and you should see the unit listed as an icon. 4. Double click the icon and a login menu will pop up. Input the default user name and password “admin” and click “OK” to continue. Nixeus Technology, Inc.
5. You can use a mouse to copy, move and delete your media files between your PC the units local HDD. Music, Photo & Video Playback For detailed information on supported file formats, refer to the user manual. Some the functions that are more regularly used are highlighted in the following pages: Nixeus Technology, Inc.
Viewing Video Information 1. Press the “Info” button to display the video information. 2. Press the button again to see any additional info. Nixeus Technology, Inc.
Viewing elapsed time and percentage played of file 1. To view elapsed time and the percentage of a music or video file being played, press the “0(GOTO)” button on the remote control to enter time seek mode, and press the numeric buttons directly for the percentage of time in the file being played that you wish to view. 2. Photo Slide Show: Press ‘OK’ on the selected photo thumbnail to view it full-screen display and press again to start the slide show. 3.
