USER MANUAL Nixeus Technology, Inc Nixeus Technology, Inc
About This Guide This Quick Installation Guide provides you with the information to setup your unit and enjoy viewing your multimedia files. The User Manual will describe the unit in more detail. Please go to http://www.nixeus.com to download it. Safety Information WARNING: Failure to follow these safety instructions could result in fire, electric shock, or other injury or damage.
CAUTION: About Laser and LED Use of controls or adjustments, or performance of procedures other than those specified herein my result in hazardous radiation exposure. This device complies with International Standard IEC 60825-1:2001-08 for a Class 1 and Class 2 laser product. This device also complies with 21CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001.
System Requirements One Display (projector or TV set) with HDMI or Composite video (CVBS) ports and analogue audio or optical digital audio ports. HDMI or Composite cables and analog or optical digital audio cables. An Ethernet or Wireless network and a broadband Internet connection (DSL/Cable/LAN). The Fusion XS supports several ways to share and play media files or stream content from its original destination in a PC or NAS device over the network.
Power light Rear View On/Off Button S/PDIF HDMI USB Host Ethernet Power USB Host Composite Standby Mode: When you press the Power key on the remote control or the On/Off button on the unit, the system will enter standby mode. Power Off: If you want to power off the system, please press the power key on the remote control for more than 2 seconds when the unit is operating or the On/Off button for more than 5 seconds when the unit is in standby mode.
Power On/Standby LED “Red”: ● The power supply is attached but the device has not been powered on yet or the device has been powered off after use. “Orange” ●: The device is in standby or in the process of turning on. “Green” ●The device is operating.
Installation and Connection Video & Audio The HDMI port is used for connecting your Fusion XS to your TV so you can view high-definition video and audio. The Optical S/PDIF connection is for connecting your unit to an external decoder or amplifier for high definition audio. The A/V Phone jack is for connecting your unit to the CVBS/Analog audio RCA connectors on your TV. The adapter cable pictured below is included in the product package.
Network Connection The Ethernet port or Wireless dongle (optional) are used to connect the unit to your home network router for local area network (LAN) or Internet connections. To obtain a Wireless Dongle, consult your local Nixeus representative. Remote Control The remote control is used to navigate menus and to select and watch videos, listen to music, or view photos on your TV. Some keys are not functional and reserved for future features and functions.
1 2 6 8 7 5 9 10 4 0 11 0 12 14 0 0 13 0 3 Nixeus Technology, Inc 9
The table below lists the button functions of the remote control. *KEYS NOT MENTION BELOW ARE RESERVED FOR FUTURE FUNCTIONS AND FEATURES REMOTE CONTROL KEY FUNCTION TABLE No. KEYPAD FUNCTION DESCRIPTION 1 Power 2 Mute 3 Enable/ Disable Menu. 4 Menu Vol ┼ 5 Vol ─ Decrease the volume. 6 1~0 7 Prev 8 Next 9 Info Turn On/Off Fusion XS. Mute audio output. Increase the volume. Input numbers when required. 1. Go to the previous page when browsing media files. 2.
1. Turn on the unit. The LED on the front panel of the Fusion XS will turn orange during system boot up and then green when it’s ready. Note: The default display of the unit is Composite (CVBS). If you use HDMI, cycle through the TV output modes to get the correct display mode. Wired Network Setup The default network type on the unit is wired network. Please connect the supplied Ethernet cable to your router and the Ethernet port of the Fusion XS. 1. Under Setup, you can check the Network status. 2.
Wireless Network Setup The unit supports wireless networking with a USB Wi-Fi dongle supplied by Nixeus Technology. To enable wireless function, please make sure you plug the Wi-Fi dongle into the USB port before powering on the unit. Please note that a USB Wi-Fi dongle not supplied by Nixeus Technology may NOT be supported. For high-definition video streaming a wired Ethernet connection between the unit and your network is recommended. Playback of normal video (eg.
Local Storage Devices The unit supports external USB flash disks, USB HDDs. Connect a USB storage enclosure to the USB port of the unit. 1. Under Video/Music/Photo, select the USB storage enclosure and the target video/music/photo file. 2. Press to play the file. Refer to the Remote Control Key Function Table to find out the related functions of playing video/music/photo files.
Nixeus Technology, Inc 14
Web Browser 1. The Default homepage is Google in the Web Browser 2. In the Address bar or in the search box, you can input a website or keywords by pressing up an on-screen keyboard.
Watching YouTube Content YouTube content can be streamed to the Fusion XS 1. Under YouTube, press to play the content, or input keywords to search for certain contents. Install/Uninstall APK Files The Fusion XS integrates the Android OS and supports a number of applications from installing Android Package files. After downloading an APK file from the Internet on a PC, put the file on a USB storage device for installation onto the unit.
Install APK Files 1. Insert the USB storage device into the USB port on the unit. 2. Under Application, select OI File Manager mnt usb select the USB storage device select an APK file. Press 3. to install the APK file and then open it. The installation of the APK file is completed.
Uninstall APK Files To uninstall an APK files from the unit. 1. Under Application Settings 2. Applications Manage Applications 3.
4. To verify that the uninstallation is finished” Check that the uninstalled APK file is no longer located under Applications. 5. If it is not there then the un-installation of the APK file is complete. Firmware Upgrade To check the firmware version on your unit, go to Version under Setup. It will show the current firmware version (eg. Firmware Version: 00.99.01.30.00). New Firmware versions can be downloaded from the following location: http://www.nixeus.
To upgrade the firmware on your unit, follow the steps below: 1. Under Setup Version USB Upgrade New Firmware is found on the USB storage device. 2. Press 3. The “Nixeus” screen will play a number of times after upgrading to the new firmware . to initiate the process of upgrading to the new firmware. 4. Once you are at the unit’s main screen, the firmware upgrade is complete.