Installation Guide

ManualsBrandsNo Drilling Required ManualsBathKlaam Double Robe Hook in Chrome

Bath Accessory Installation

• Step 1 - Clean surface using a clean dry cloth or use

rubbing alcohol to remove any residue (wax, grease,

solvents). Allow to dry one hour. Caution! DO NOT use

any household cleaners as they can leave a residue.

• Step 2 - Locate position desired and mark. Remove

protective paper from foam securing ring and apply firm

pressure for 4 seconds. Avoid mounting adapter over

grout lines.

• Step 3 – Use the red key end to puncture the adhesive

tube. Slide tube end into slot in red key and turn the key

until firm.

• Step 4 – Insert tube end into one hole of the adapter.

Turn the red key forcing the adhesive into the adapter

base until the white adhesive beads up out of the other

hole. Caution! DO NOT apply any pressure or disturb the

adapter once the adhesive has been inserted.

• Step 5 – Allow adapter to cure (harden) for 12 hours

undisturbed. Remove any excess adhesive once dry.

Caution! Allow 24 hours for Grab Bars

• Step 6 – Mount your accessory using the tool provided

and enjoy!

Note: Surface must be able to bear load of accessory. Not intended for use on Polyethylene (PE)

Polypropylene (PP), Polytetraflouroethylene (PTE, Teflon) as they do not allow for proper adhesion

Summary of content (8 pages)

PAGE 1
Bath Accessory Installation • • • • • • Step 1 - Clean surface using a clean dry cloth or use rubbing alcohol to remove any residue (wax, grease, solvents). Allow to dry one hour. Caution! DO NOT use any household cleaners as they can leave a residue. Step 2 - Locate position desired and mark. Remove protective paper from foam securing ring and apply firm pressure for 4 seconds. Avoid mounting adapter over grout lines. Step 3 – Use the red key end to puncture the adhesive tube.
PAGE 2
Bath Accessory Installation • • • • • • Step 1 - Clean surface using a clean dry cloth or use rubbing alcohol to remove any residue (wax, grease, solvents). Allow to dry one hour. Caution! DO NOT use any household cleaners as they can leave a residue. Step 2 - Locate position desired and mark. Remove protective paper from foam securing ring and apply firm pressure for 4 seconds. Avoid mounting adapter over grout lines. Step 3 – Use the red key end to puncture the adhesive tube.
PAGE 3
Installation Tips-Two Post Accessories • For accessories with more than one adapter: – Use small piece of packaging & insert into base behind adapter – Carefully insert adapters into the accessory & lightly fasten with tool (the packaging will keep the adapter sitting tall which allows for easy attachment of the adhesive ring) – Remove protective film from ring – Hold accessory up to the marks and press adapters firmly into place – Carefully remove accessory and follow instructions for adhesive insertion an
PAGE 4
Shower Caddy Installation Clean surface with alcohol pad and let dry. Do not use household cleaners! Step 1: Attach adapters to caddy using chrome cover nuts Step 2: Use caddy to identify desired location prior to removing adhesive ring cover. Mark and check level, use masking tape to avoid marking surface Step 3: Peel protective cover ring and carefully press in place on marks.
PAGE 5
Grab Bar Installation Instructions (GB Series) Adapter Set- 2 Adapters, 3adhesive tubes, 3-Red Keys, 6 stainless screws, 1 alcohol pad Clean surface with alcohol pad, let dry fully. Do not clean with household cleaners! Carefully remove cover ring from each side. Foam ring will hold adapters in place on wall and provide a border for the adhesive when inserted. Press bar at desired location firmly for 5 seconds. Remove bar.
PAGE 6
Assist Bar Installation 1. Use level and mark location for bar placement. 2. Use moist towel to clean surface, allow 1 hour to dry completely 5. Caution: Once adapter makes contact with surface, it cannot be removed without damaging ring. Be sure you have clearly marked location before attaching to surface. Firmly press adapters on to surface. Remove bar. 3. Loosely attach adapter to base 4. Carefully remove protective ring cover 6. Pierce end of tube with end of red roller stick.
PAGE 7
Shower Bar Installation Step 1: Remove chrome cover cap from each of the two chrome posts and carefully loosen dual set screws Step 2: Slide the adjustable holder onto middle of the bar by squeezing the button. Slide ends pieces onto bar and lightly tighten dual set screws Step 3: Position in shower to optimum height and adjust chrome post to desired position. Tighten dual set screws until firm (do not over tighten) Step 4: Clean surface with alcohol pad and let dry completely.
PAGE 8
Adapter Removal • The nie wieder bohren adapter system can be removed from any hard surface by applying torsion • Step 1 – Use a pair of adjustable grips and firmly turn the adapter counterclockwise. • Step 2 – Remove residual adhesive from surface using a razor knife and wipe with acetone remover as needed.