Assembly Instructions Caution : You must read this before you proceed CONSOLE TABLE Part List Label Picture Description QTY A Table Top 1 B Top Support 2 C Table Leg Right (C) 2 D Table Leg Left (D) 2 Noble House Home Furnishings LLC Page 1 of 8
E Top Stretcher 2 F H Rail 2 G Cross Rail 1 H Top Support Rail 1 Description QTY ① JCBB M8 x 30mm + S/W 5/16" + F/W 5/16" x 22mm 9 ② Allen Wrench M5 1 ③ JCBC M6 x35mm + S/W M6 + F/W M6 x 19mm 9 ④ JCBC M6 x 40mm + S/W M6 + F/W M6 x 13mm 3 ⑤ JCBC M6 x 60mm + S/W M6 + F/W M6 x 13mm 5 ⑥ Allen Wrench M4 1 ⑦ FH Screw #8 x 38mm 9 ⑧ Wood Dowel M8 x 25mm 5 ⑨ Screwdriver(Not Provided) 1 Hardware Label Picture Noble House Home Furnishings LLC Page 2 of 8
Assembly Preparation Before Beginning Assembly: Assembly Steps Overview Top Support (B) Table Top (A) Top Support Rail (H) Top Stretcher (E) Table Leg Left (D) Table Leg Right (C) Cross Rail (G) H Rail (F) This Console Table has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Console Table parts, the above picture is to help you put the various parts into perspective.
Step 1 DIRECTION ARROW STICKER DIRECTION ARROW STICKER Place the Top Support (B) on a surface and slot in the Table Leg Left (D) onto the Top Support (B) as shown. Make sure the Top Support is at the right position by the marking arrow sticker. Affix the Table Leg Left (D) with JCBB Bolts ① + Spring Washers + Flat Washers using the Allen Wrench ②. Repeat step for the Table Leg Right (C) as shown. Step 2 Slot in the Top Stretcher (E) and H Rail (F) onto the Table Leg Left (D) as shown.
Step 3 Affix the Table Leg Right (C) with JCBB Bolts ① + Spring Washers + Flat Washers into the Top Support (B) and tighten it by using the Allen Wrench ②. Repeat the step for the Table Leg Left (D). Step 4 Affix both Top Stretchers (E) and both H Rails (F) with FH Screws ⑦ onto both the Table Leg Right (C) and Table Leg Left (D) and tighten them by using a Screwdriver (Not Provided).
Step 5 5.1 5.3 5.2 DIRECTION ARROW STICKER Place the Table Top (A) on a soft surface to avoid any scratches or damages to the product. 5.1 Slot in the Wood Dowel ⑧ into the Top Support (B) as shown. 5.2 Attach the Top Support (B) into the designated hole at the Table Top (A). 5.3 Slot in the Cross Rail (G) into the Table Leg as shown. Repeat step 5.1, 5.2 and 5.3 with another leg as shown. Step 6 6.2 6.1 6.
Step 7 Place the Top Support Rail (H) on the center table top as shown and affix it with the JCBC Bolts ⑤ + Spring Washers + Flat Washers and tighten by using the Allen Wrench ⑥. DO NOT FULLY TIGHTEN THE BOLTS. Step 8 With assistance from your adult partner, stand the table up. If the table wobbles, loosen and tighten the screws and bolts, and use your hand to press down on the top of the table, to ensure eveness, and then fully tighten the bolts sequentially. FULLY TIGHTEN THE BOLTS.
Care & Maintenance Noble House Home Furnishings LLC Page 8 of 8
