Instructions / Assembly

ManualsBrandsNoble House ManualsFabric HammocksRichardson 13.68 ft. Free-Standing Hammock in Light Green

Label Picture Description QTY

A Supporting Bar 2

Mid-Joint Support Bar 2

C Ground Bar 2

M Hammock 1

O Rope with Carabiners 4

Picture

Hammock on Wooden Stand

Caution: You must read this before you proceed

CAUTION : Do Not Swing on or in Hammock. This could cause the product to tip over

resulting in possible injury.

This Hammock on Wooden Stand is NOT a TOY.

Keep your child / children at bay in the process of assembly.

Have at least three adults to assit when assembling this Hammock on Wooden Stand.

1 OF 8

Summary of content (8 pages)

PAGE 1
Hammock on Wooden Stand Caution: You must read this before you proceed Picture CAUTION : Do Not Swing on or in Hammock. This could cause the product to tip over resulting in possible injury. This Hammock on Wooden Stand is NOT a TOY. Keep your child / children at bay in the process of assembly. Have at least three adults to assit when assembling this Hammock on Wooden Stand.
PAGE 2
Label Picture Description QTY D Bolt (M10*13CM) 4 E Washer 19 F Nut 10 L Bucket Wrench 2 H Bolt (M10X23CM) 4 J Metal Chain with Iron Carabiners 2 K Eye Bolt (M10*60MM) 2 Q Bolt and Ring Nut (M8*15MM) 4 R Allen Key 1 N Bolt and Ring Nut (M8*11CM) 2 Before Beginning Assembly: 2 OF 8
PAGE 3
This Hammock has multiple parts and may require up to 60 minutes to assemble. To give you an overview of the Hammock parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. NOTE: It is recommended that you have a partner to assist durning the entire assembly process. Step 1 Note : The COUNTERSINK hole side of Wooden Bar(B) should be on the outside.
PAGE 4
Step 2 NOTE : Have a couple of partners / assistants when assembling this step. Put Supporting Bars(A) between Mid-Joint Supporting Bars(B). Then attach using Bolts(H), Washers(E) and Nuts(F) with Bucket Wrenches(L). Tighten the Bolts in a sequential manner until fully secure. Step 3 E NOTE : This step should be completed with two or more people. Complete the assembly of Mid-Joint Support Bar(B) to Ground Bar(C) from Step 1 using Washers(E), and Nuts with Bucket Wrenches(L).
PAGE 5
Step 4 Attach the Eye Bolts(K) to the tail end of the Supporting Bars(A) using Washers(E) and Nuts(F) with Bucket Wrench(L). Tighten the Bolts in a sequential manner until fully secure. Note: The Eye Bolts should be facing the inside of the frame assembly, as pictured. Step 5 Screw the Bolt and Ring Nuts(Q) to the four ends of the Wooden Support Rails with Allen Key(R) Tighten the Bolts in a sequential manner until fully secure.
PAGE 6
Step 6 N Insert the Bolt and Ring Nuts(N) into the Supporting Bars(A), as shown in the picture. Tighten the Bolts of this step completely by hand. Step 7 J J M Hook the Chain with Carabiners(J) to the Loops at the ends of the Hammock(M).
PAGE 7
Step 8 Connect the Hammock(M) to the Supporting Bars(A) using the Chain with Carabiners(J). Step 9 Connect the four Eye Bolts(K) on the Hammock(M) to the Bolt and Ring Nut(N) on Supporting Bars(A) with Rope with Carabiners(O). Adjust the Chain with Carabiners(J) until the four Ropes are taut. Your Hammock on Wooden Stand is ready for use. Always be careful of your safety when getting on and off of the Hammock; children should not be allowed on the Hammock without adult supervision.
PAGE 8
OF 8