Assembly Instructions Caution: You must read this before you proceed Bird bath CAUTION: This table is NOT a TOY. Keep your child/children at bay during the assembly process.
E Lotus Seedpod 1 F Water Basin 1 Description Bolt(M8*30mm) QTY 4 ② Washer(8mm) 4 ③ Nut(8mm) 4 ④ Bolt(M6*25mm) 5 ⑤ Bolt(M6*30mm) 2 ⑥ Washer(6mm) 5 ⑦ Nut(6mm) 5 ⑧ Bolt(φ5*20mm) 2 ⑨ Spanner 1 ⑩ Screwdriver 1 ⑪ Rubber Cap(6mm) 4 Hard ware Label ① Picture Assembly Preparation Before Begin ning Assem bly: Noble house Home Furnishings LLC Page 2 OF 7
Assembly Step Overview Bird Ornament(C) Lotus Ornament(D) Lotus Seedpod(E) Water Basin(F) Pedestal(B) Base(A) FRONT FACING This Bird bath has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Bird bath parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Unpack and place all parts on a clean, soft surface.
Step 2 Turn the Pedestal(B) upside down and you will see 3 (three) mounting points. Lock Bolts(①) to the mounting positions on Pedestal(B) by using Screwdriver(⑩). Need tighten the bolts. Step 3 A B Align bolts on Pedestal(B) to the mounting positions on Base(A), attach Pedestal(B) to Base(A) with Washers(②) and Nuts(③) by using Spanner(⑨). Make sure the Base is turned upside down for this assembly. Need tighten the bolts.
Step 4 D D ⑧ E E Attach Lotus Ornament(D) to the Lotus Seedpod(E) with Bolts(⑧) by using Screwdriver(⑩). Step 5 5.1 5.2 5.1) Lock Bolt(④) to the Lotus Seedpod(E) by using Screwdriver(⑩). 5.2) Attach Bird Ornament(C) to the Bolt on Lotus Seedpod(E) by turning Bird Ornament,adjust to make the bird face the lotus,no need overtighten Step 6 6.1 6.2 6.1) Turn Lotus Seedpod(E) over as pix above. Lock Bolt(⑤) to Lotus Seedpod(E) by using Screwdriver(⑩). 6.2) Turn Lotus Seedpod(E) over as pix above.
Step 7 7.1 7.2 Stand the Bird bath upright. 7.1) Lock Bolt(④) to Water Basin(F) by using Screwdriver(⑩). 7.2) Align the bolts on Water Basin(F) to the mounting positions on Pedestal(B), attach Water Basin(F) to Pedestal(B) Washers(⑥) and Nuts(⑦) by using Spanner(⑨). Attachment points shall be locked in from the underside of the Water Basin(F). Need tighten the bolts. Step 8 Now, in a sequential manner, fully and securely tighten all bolts at all joints.
Do not put hot items directly on furniture surface. Do not clean furniture with harsh cleansers or To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct sunlight is Children should not climb or jump on the furniture. Do not write on furniture without a padded barrier to protect the surface. To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine.
