Instructions / Assembly

ManualsBrandsNoble House ManualsOutdoorsLa Vida Black Metal Patio Swing with Green Cushion

Label Picture Description QTY

Front Foot 1

Lower Support Pole 1

Back Foot 1

Upper Support Pole 1

E-L

Left Back Pole 1

E-R

Right Back Pole 1

Caution: You must read this before you proceed

Hanging Lounger

CAUTION : This Hanging Lounger is NOT a TOY.

Keep your child / children at bay in the process of assembly.

Summary of content (8 pages)

PAGE 1
Caution: You must read this before you proceed Hanging Lounger CAUTION : This Hanging Lounger is NOT a TOY. Keep your child / children at bay in the process of assembly.
PAGE 2
F-L Left Seat Pole 1 F-R Right Seat Pole 1 G U-shape Pole 1 H Back Support Bar 1 J Seat 1 K Armrest 2 L Sun Shade Connector Bracket 1 M Sun Shade Support Pole(short) 3 N Sun Shade Support Pole(long) 1 O Sun Shade 1 P Foot Pad 2 Y Cushion 1 Label Picture Description QTY Q Bolt with Nut&Washer(M8X75CM) 2 R Bolt with Nut&Washer(M10X85CM) 1 S Bolt with Nut&Washer(M8X95CM) 1 T Snap Hook 1 U1 Nut Cap(M10) 2 U2 Nut Cap(M8) 6 V Bolt 6 W Rope 1 X Spann
PAGE 3
Before Beginning Assembly: Step 1 Attach Front Foot(A) to Lower Support Pole(B) using Bolt with Nut&Washer(Q) and Allen Key(X). Put on Nut Cap(U2).
PAGE 4
Step 2 Attach Back Foot(C) to Lower Support Pole(B) using Bolt with Nut&Washer (R) and Spanner(X). Put on Nut Cap(U1). Step 3 Attach Upper Support Pole(D) to Lower Support Pole(B) using Bolt with Nut&Washer(Q) and Spanner(X). Put on Nut Cap(U2). Step 4 Put on the Foot Pad(P).
PAGE 5
Step 5 Place the Snap Hook(T) between the Left Back Pole(E-L) and Right Back Pole(ER). Insert Bolt(S) through the holes, and tighten the Bolt with Nut&Washer(S) using Spanner(X). Put on Nut Cap(U2). Connect the Left Seat Pole(F-L) to Left Back Pole(E-L), connect the Right Seat Pole(F-R) to Right Back Pole(E-R). Then connect the U-shape Pole(G) to Seat Pole(F-L&F-R). Step 6 Insert the Back Support Bar(H) into the Seat(J) as shown.
PAGE 6
Step 8 Attach the Armrest(K) to the main frame using Bolt(V) with Allen Key(Z). Step 9 Insert the Short Poles(M) and Long Pole(N) into the Bracket(L). Then insert the ends of the Poles(M&N) into the Sun Shade(O). Step 10 Connect the assembled Sun Shade to the top of the Upper Support Pole(D). Please note the Long Pole(N) should be on the back side. Then tighten the Snap Bottom as shown.
PAGE 7
Step 11 Connect the Lounger to the Upper Support Pole by the Snap Hook(T). Step 12 Place the Cushion(Y) onto the lounger and secure it by tying tightly to the frame. Your Hanging Lounger is ready for use. Caution: When you want to get on the Lounger, first sit on the armrest position, then put on your feet and lie down. Always be careful of your safety when getting on and off the Lounger. Children should not be allowed to use the Lounger without adult supervision.
PAGE 8