Assembly Instructions Caution: You must read this before you proceed CHAIR Caution: This Chair is NOT a TOY. Keep your child / children at bay in the process of assembly. For turning the Chair and to prevent damage to the Chair, 02 persons may be needed to execute this action.
Parts List Label A B Picture Description QTY Backrest Panel 1 Seat Panel 1 C Left Leg Panel 1 D Right Leg Panel 1 E Rocking base 2 F Left Leg Support Bar 1 G Right Leg Support Bar 1 H Seat Cushion 1 Noble House Home Furnishings LLC Page 2 of 9
Hardware Note: A Long Bolt (②) will be used to guide in the Cross Nut (⑤) This Bolt is to be kept with Allen Key as spare Hardware Label Picture Description QTY ① Screw (M6*80mm) 7 ② 7 ⑤ Long Bolt (M6*70mm) Short Bolt (M6*35mm) Sleeve Nut (M6x15mm) Cross Nut (M6x13mm) ⑥ Allen Key 2 ③ ④ 3 3 7 Assembly Preparation Before Beginning Assembly: Noble House Home Furnishings LLC Page 3 of 9
Assembly Steps Overview Right Leg Panel (D) Backrest Panel (A) Left Leg Panel(C) Seat Cushion (H) Seat Panel (B) Rocking base(E) Left Leg Support Bar(F) Right Leg Support Bar(G) FRONT FACING This Chair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Chair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 2 2 2.2 D E 5 2 2 6 2.1.1 2.1.2 Position Right Leg Panel (D) to Rocking Base (E) 2.1.1) Attach Long Bolt (②) to the top of Cross Nut(⑤) by hand,turning clockwise. Insert both into housing position of Right Leg Panel( D) 2.1.2) Insert the Long Bolt (②) through the housing position of Rocking Base (E) and affix to Cross Nut (⑤) inside of Right Leg Panel( D), tighten with Allen Key(⑥) 2.2) Remove the first Long Bolt (②) by hand Do not fully tighten the Bolts.
Step 3 2 D 3.2 E G 2 5 6 3.1.1 2 3.1.2 6 4 3 6 3.3 Position Right Leg Support Bar (G) to Rocking Base (E) and Right Leg Panel (D) 3.1.1) Attach Long Bolt (②) to the top of Cross Nut(⑤) by hand, turning clockwise. Insert both into housing position of Right Leg Support Bar (G) 3.1.2) Insert the Long Bolt (②) through the housing position of Rocking Base (E) and affix to Cross Nut (⑤) inside of Right Leg Support Bar (G), tighten with Allen Key(⑥) 3.2) Remove the first Long Bolt (②) by hand 3.
Step 4 B D C 6 B 1 4.1 4.2 4.1) Place the Left Leg in Step 3 with inside face skywards onto a clean, soft surface to avoid any scratches or damages to the product Position the Seat Panel (B) to Left Leg Panel (C) as shown. 4.2) Attached Right Leg Panel (D) in Step 3 into Seat Panel (B), secure by using Screw (①) and Allen Key (⑥). Do not fully tighten the Screws.
Step 6 H Inspect the Chair and make sure all parts are adequately connected. In a sequential manner, tighten all Bolts and Screws at all joints. Place Seat Cushion (H) on to the Chair using the velcro straps as shown above. Your Chair is ready for use. This Chair can only be used on a flat, level surface.
Noble House Home Furnishings LLC Page 9 of 9