Caution : You must read this before you proceed Chair Label Picture Description QTY A Backrest 1 B Seat 1 C Right Armrest / Leg 1 D Left Armrest / Leg 1 E Seat Cushion 1 Page 1 OF 6
Label Picture Description QTY 1 2 3 4 5 Bolt(M6*55MM) Bolt(M6*35MM) Bolt(M6*25MM) Washer Nut Cap 3 3 9 15 3 6 Allen Key 1 Before Beginning Assembly: Overview Left Armrest / Leg(D) Seat Cushion(E) Backrest(A) Right Armrest / Leg(C) Seat(B) This Chair has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Chair parts, the above picture is to help you put the various parts into perspective.
Step 1 3 2 6 6 4 4 Open the carton and place all the parts onto a clean and soft surface. Unpack all packages of hardware. Place the Backrest (A) with its inside facing skywards. Attach Seat(B) to Backrest(A) using Hardware( 2 3 4 ) with Allen Key( 6 ) as shown in Picture 1 and Picture 2. Do not fully tighten the bolts. ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting positions preventing easy assembly.
Step 3 4 4 3 6 4 C Place the Right Armrest / Leg (C) as pictured above and affix to Right Armrest / Leg(C) and Seat(B) using Hardware( 3 4 ) with Allen Key( 6 ) as shown in Picture 4. Do not fully tighten the bolts. Step 4 6 5 1 4 6 D 1 4 A 6 C Connect the Armrest/Leg (C&D) to Backrest (A) using Hardware( 1 4 )with Allen Key ( 6 ) as shown in Picture 5 and Picture 6 Note: DO NOT fully tighten a BOLT in one go and then move on to the next.
Drop the Single Chair freely and vertically with all four legs, hitting the ground, all at the same time. This Drop Test will help to ensure that all the Bolts and gaps reach full alignment status. Test again for evenness on a LEVEL SURFACE. If no wobbles are found, slowly and steadily, place the Single Chair facedown. Then, proceed to tighten all Bolts in a sequential manner. When tightening the Bolts, tighten sequentially. DO NOT tighten any Bolt fully and then move on towards the next one.
Do not put hot items directly on furniture surface Do not clean furniture with harsh cleansers or polish. To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct sunlight is recommended. Children should not climb or jump on the furniture. Do not write on furniture without a padded barrier to protect the surface. To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine.
Caution: You must read this before you proceed.
Before Beginning Assembly: Unpack all the parts for a clear overview. Overview Table Top (A) Leg Panel (B) Leg Support Panels (C) This Table has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts on a clean, non-marring surface. Turn table top upside down, then attach Leg Panel (B) to the Table Top(A) using Bolt(③) and Washer(②) with Allen Key(①) as shown in the picture above. Repeat this process with the other Leg Panel(B) Do not fully tighten the Bolts. Step 2 Attach Leg Support Panel(C) between Leg Panels(B) using Bolt(③) and Washer(②) with Allen Key(①) as shown in the picture above.
Step 3 If wobble Test again 30CM~50CM Place the table on a LEVEL SURFACE to check for wobbles. If it wobbles,with 2 to 3 adult partners, lift the table to some 30cm to 50cm height from the ground. Keep your feet and toes well away from the drop zone. Drop the table freely and vertically with the four legs, hitting the ground, all at the same time. This Drop Test will help to ensure that all the bolts and gaps to all reach full alignment status. Test again for evenness on a LEVEL SURFACE.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.