Caution : You must read this before you proceed Left Armchair Noble house Home Furnishings LLC 1 OF 7
Label Description QTY G Seat 1 H Backrest 1 D Right Panel 1 I Left Armrest 1 E Seat Cushion 1 F Back Cushion 1 Description QTY ① Bolt Cap 13 ② Bolt (M6*40mm) 12 ③ Washer 13 ④ Allen Key 1 ⑤ Bolt (M6*50mm) 2 Label Picture Picture Noble house Home Furnishings LLC 2 OF 7
Before Beginning Assembly: Overview This Left Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Left Armchair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean, non-marring surface. Place the Right Panel(D) with its inside facing up . Attach Seat(G) to Right Panel(D) using Bolt(②) and Washer(③) with Allen Key(④) as shown above. Only loosely tighten Bolts. ATTENTION: There may be some PE wicker that may have covered the Mounting Points. To ease assembly, guide and slide the PE wicker away from these Mounting Points.
Step 3 Place the Left Armrest(I) with its inside facing up . Attach Seat(G) to Left Armrest(I) using Bolt(②) and Washer(③) with Allen Key(④) as shown above. Only loosely tighten Bolts. Step 4 Stand the Chair right way up. Attach Left Armrest(I) to Backrest(H) using Bolt(⑤) and Washer(③) with Allen Key(④) as shown above. Only loosely tighten Bolts.
Step 5 Turn the Chair right side up. Place the Chair on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and gracefully, sit into to the Chair. This would help to align all the parts at all the joint areas. Then get off the Chair, and in a sequential manner, proceed to tighten all bolts. When tightening the Bolts, tighten sequentially. DO NOT tighten any Bolt fully and then move on to the next one. This may cause the frame to warp.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Armless Chair Label Picture Description QTY A Seat 1 B Backrest 1 C Left Panel 1 D Right Panel 1 E Seat Cushion 1 F Back Cushion 1 Noble house Home Furnishings LLC 1 OF 6
Label Picture Description QTY ① Bolt Cap 13 ② Bolt (M6*40mm) 13 ③ Washer 13 ④ Allen Key 1 Before Beginning Assembly: Over View This Armless Chair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Armless Chair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean, non-marring surface. Place the Left Panel(C) with its inside facing up . Attach Seat(A) to Left Panel(C) using Bolt(②) and Washer(③) with Allen Key(④) as shown above. Only loosely tighten Bolts. ATTENTION: There may be some PE wicker that may have covered the Mounting Points. To ease assembly, guide and slide the PE wicker away from these Mounting Points.
Step 3 Place the Right Panel(D) with its inside facing up . Attach Seat(A) to Right Panel(D) using Bolt(②) and Washer(③) with Allen Key(④) as shown above. Only loosely tighten Bolts. Step 4 Turn the Chair right side up. Place the Chair on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and gracefully, sit into to the Chair. This would help to align all the parts at all the joint areas. Then get off the Chair, and in a sequential manner, proceed to tighten all bolts.
Step 5 Use the Bolt Cap(①) to cover all Bolts. Step 6 Place the Back Cushion (F) and Seat Cushion(E) onto the Corner as shown. Your Armless chair is ready for use. Caution:This Ottoman can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed CORNER Noble house Home Furnishings LLC 1 OF 7
Label Description QTY M Seat 1 N Backrest 1 O Right Panel 1 C Left Panel 1 E Seat Cushion 1 P Back Cushion 1 Q Back Cushion 1 Description QTY ① Bolt Cap 14 ② Bolt (M6*40mm) 14 ③ Washer 14 ④ Allen Key 1 Label Picture Picture Noble house Home Furnishings LLC 2 OF 7
Before Beginning Assembly: Overview This Corner has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Corner parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean, non-marring surface. Place the Left Panel(C) with its inside facing up . Attach Corner Seat(M) to Left Panel(C) using Bolts(②) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Occasionally some of the PE Wicker shifts and covers the mounting positions preventing easy assembly. The PE Wicker should never be cut, but moved away from the mounting positions. Step 2 Place the Right Panel(O) with its inside facing up .
Step 3 Place the Backrest(N) with its inside facing up . Attach Corner Seat(M) to Backrest(N) using Bolts(②) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Occasionally some of the PE Wicker shifts and covers the mounting positions preventing easy assembly. The PE Wicker should never be cut, but moved away from the mounting positions. Step 4 Stand the Corner up. Place the Corner on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected.
Step 5 Use the Bolt Caps(①) to cover all Bolts(②). Step 6 Place the Seat Cushion(E) and Back Cushions(P) & (Q) onto the Corner as shown. Your Corner is ready for use. This Corner can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Right Armchair Noble house Home Furnishings LLC 1 OF 7
Label Description QTY J Seat 1 K Backrest 1 C Left Panel 1 L Right Armrest 1 E Seat Cushion 1 F Back Cushion 1 Description QTY ① Bolt Cap 13 ② Bolt (M6*40mm) 12 ③ Washer 13 ④ Allen Key 1 ⑤ Bolt (M6*50mm) 2 Label Picture Picture Noble house Home Furnishings LLC 2 OF 7
Before Beginning Assembly: Overview This Right Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Right Armchair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean, non-marring surface. Place the Left Panel(C) with its inside facing up. Attach Seat(J) to Left Panel(C) using Bolts(②) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Occasionally some of the PE Wicker shifts and covers the mounting positions preventing easy assembly. The PE Wicker should never be cut, but moved away from the mounting positions.
Step 3 Place the Right Armrest(L) with its inside facing up. Attach Seat(J) to Right Armrest(L) using Bolts(②) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Occasionally some of the PE Wicker shifts and covers the mounting positions preventing easy assembly. The PE Wicker should never be cut, but moved away from the mounting positions. Step 4 Stand the Chair up. Attach Right Armrest(L) to Backrest(K) using Bolts(⑤) and Washers(③) with Allen Key(④) as shown above.
Step 5 Place the Chair on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and gracefully, sit into to the Chair. This would help to align all the parts at all the joint areas. Then carefully get off the Chair, and in a sequential manner, proceed to tighten all Bolts. When tightening the Bolts, tighten sequentially. DO NOT tighten any Bolt fully and then move on to the next one. This may cause the frame to warp.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Table Label Picture Description QTY U Tabletop 1 V Leg 4 Noble house Home Furnishings LLC 1 OF 6
Label Picture Description QTY ① Bolt Cap 9 ⑦ Bolt (M6*20mm) 9 ③ Washer 9 ④ Allen Key 1 Before Beginning Assembly: Noble house Home Furnishings LLC 2 OF 6
Overview This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton ang place all the parts onto a clean,non-marring surface. Attach Leg（V）onto the Tabletop（U）with Bolt（⑦）and Washer(③) using Allen Key(④). Caution: The Tabletop is heavy.
Step 2 Repeat Step 1 with the remaining three Legs（V）.Ensure all Legs are tightly and securely attached. Step 3 Stand the Table right way up. Place the Table on a LEVEL SURFACE to check for wobbles. If it wobbles, lift the table some 20cm to 30cm high from the ground. Keep your feet and toes well away from the drop zone. Drop the table freely and vertically with all four legs, hitting the ground, at the same time. This Drop Test will help to ensure that all Bolts and gaps reach full alignment status.
Step 4 Use the Bolt Cap(①) to cover all Bolts(⑦). Step 5 Stand the Table right way up. Your Table is ready for use. This Table can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
