Caution : You must read this before you proceed Single Sofa Label Picture Description QTY A Sofa - Backrest 1 B Right Armrest 1 C Left Armrest 1 D Sofa Seat 1 Page 1 OF 6
Label Picture Description QTY F Plastic Cap 13 G Bolt M6*40mm 13 H Washer 13 I Spring Washer Ø16*2mm 13 J Allen Key 1 Before Beginning Assembly: Page 2 OF 6
Overview Sofa - Backrest(A) Right Armrest(B) Sofa Seat(D) Left Armrest(C) This Single Sofa has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Single Sofa parts, the above picture is to help you put the various parts into perspective. Please read through the instructions herebelow to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all the parts onto a clean and soft surface. Unpack all packages of hardware.
Step 2 Place the Seat (D) between the Right Armrest(B) and Backrest(A). Attach the Seat(D) to the Right Armrest(B) with hardware as picture 3 and 4 shows. Use an Allen Key(L) to partially tighten these. Do not fully tighten the bolts. Step 3 Place the Left Armrest (C ) against the Backrest(A) and Seat(D). Make the metal rod on the Backrest(A) insert into the MOUNTING POSITIONs of the Left Armrest(C ) as picture 5 shows. Attach the Left Armrest(C ) to Backrest(A) with hardware as picture 6 shows.
Step 4 Tighten all bolts completely. Put the Plastic Cap(F) to cover the bolt heads, adjust the Leveler to ensure good stability. Step 5 It is ready for use. This Single Sofa can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Ottoman Label Picture Description QTY O Top Panel 1 P Front/Back Panel 2 Q Side Panel 2 Page 1 OF 6
U Seat Cushion 1 Description QTY ① Bolt Cap 13 ② Bolt (M6*40mm) 13 ③ Washer 13 ④ Spring Washer (Ø16*2mm) 13 ⑤ Allen Key 1 Label Picture Before Beginning Assembly: Page 2 OF 6
Overview Seat Cushion(F) Top Panel(O) Front Panel(P) Side Panel(Q) This Ottoman has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Ottoman parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all parts on a clean, non-marring surface.
Step 2 Place the Top Panel(O) facedown on a clean and soft surface. With the help of your adult partner, turn the Table Frame over and place it onto the Top Panel(O) as shown above. Attach the Top Panel(O) to the Front and Back Panels(P) and Side Panels(Q) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above. Tighten all Bolts at all joints completely at this stage. Step 3 Use the Bolt Cap(①) to cover all Bolts.
Step 4 Place the Ottoman on a level surface to check the wobbles. If the Ottoman wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 5 Place the Seat Cushion(U) on the ottoman. Your Ottoman is ready for use. This Ottoman can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
Caution : You must read this before you proceed Table Label Picture Description QTY V Top Panel 1 W Front/Back Panel 2 X Side Panel 2 Page 1 OF 6
Label Picture Description QTY ① Bolt Cap 13 ② Bolt (M6*40mm) 13 ③ Washer 13 ④ Spring Washer (Ø16*2mm) 13 ⑤ Allen Key 1 Before Beginning Assembly: Page 2 OF 6
Overview This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all parts on a clean, non-marring surface.
Step 2 Place the Top Panel(V) facedown on a clean and soft surface. With the help of your adult partner, turn the Table Frame over and place it onto the Top Panel(R) as shown above. Attach the Top Panel(R) to the Front and Back Panels(S) and Side Panels(T) using Bolts(②), Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above. Tighten all Bolts at all joints completely at this stage. Step 3 Use the Bolt Cap(①) to cover all Bolts.
Step 4 Place the Table on a level surface to check the wobbles. If the Table wobbles, adjust the Levelers on the bottom of the Legs to make it level. Step 5 Your Table is ready for use. This Table can only be used on a flat, level surface.
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.
