Caution: You must read this before you proceed Loveseat Label Description QTY A Side Panel 2 B Back Support Bar 1 C Seat (Labelled with face and bottom) 1 Description QTY D Bolt:M6*20MM 11 E Allen Key 1 F Seat Cushion 2 G Back Cushion 2 Label Picture Picture
Before Beginning Assembly: Step 1 Take out the silders in the four ends of the Seatboard(C ) using Allen Key(E ). Step 2 Open the carton and place all the parts on a clean, non-marring surface. Insert the Seat(C) into the Side Panel(A), shown as the picture.
Step 3 Attach Seat(C) and Side Panel(A) using Bolt(D) and Allen Key(E). Loosely tighten the Bolts. Step 4 Attach Back Support Bar(B) to Side Panel(A) using Bolt(D) with Allen Key(E). Loosely tighten the Bolt. Step 5 Repeat Step 1 to Step 3 to attach the second Side Panel(A). Loosely tighten the Bolts.
Step 6 Stand up the loveseat frame , check stability and then tighten the bolts. Note DO NOT fully tighten a BOLT in one go and then move on to the next. Rather, In a sequential manner, gradually tighten each Bolt until all bolts are evenly secured. This methodology will ensure maximum evenness once all Bolts are fully tightened. Step 7 Put the Seat Cushions(F) and Back Cushions(G) on the Loveseat. Your Loveseat is ready for use.
Caution: You must read this before you proceed Single Chair Label Description QTY A Side Panel 2 B Back Support Bar 1 C Seat (Labeled with face and bottom) 1 Description QTY Bolt:M6*20MM 10 Label D Picture Picture
E Allen Key 1 F Seat Cushion 1 G Back Cushion 1 Before Beginning Assembly: Step 1 Take out the silders in the four ends of the Seatboard(C ) using Allen Key(E ).
Step 2 Insert the Seat(C) onto the Side Panel(A), as shown in the picture. Step 3 Attach Seat(C) and Side Panel(A) using Bolt(D) with Allen Key(E) as shown in the picture. Loosely tighten the Bolts. Step 4 Attach Back Support Bar(B) to Side Panel(A) using Bolt(D ) with Allen Key(E). Loosely tighten the Bolts.
Step 5 Repeat Step1 to Step 3 to attach the second Side Panel(A). Place chair upright and test for stability. Then in a sequential manner, proceed to fully tighten all Bolts at all joints. Step 6 Stand the Chair up. Put Back Cushion(G) and Seat Cushion(F) on the Chair, and stick the vercro. Your Single Chair is ready for use.
Caution : You must read this before you proceed Right Sofa Label Picture Description QTY A Side Panel 1 B Back Support Bar 1 C Seat Panel (Labeled with 'face' and 'bottom') 1 D Leg Support Bar 1 E Seat Cushion 2 F Back Cushion 2 Page -4105 OF 8
Label Picture Description QTY ① Bolt (M6*20MM) 11 ② Allen Key 1 Before Beginnin g Assembly : Page -4104 OF 8
Overview Back Cushion(F) Back Support Bar(B) Side Panel(A) Seat Panel(C) Seat Cushion(E) Leg Support Bar(D) FRONT FACING This Sofa has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Sofa parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Step 1 Open the carton and place all the parts onto a clean, non-marring surface.
Step 2 Place the Side Panel(A) with its inside facing up. Insert Seat Panel(C) into the Side Panel(A). Step 3 3.1) Attach the Seat Panel(C) to Side Panel(A) using Bolts(①) with Allen Key(②) as shown above. 3.2) Attach the Seat Panel(C) to Side Panel(A) using Bolts(①) with Allen Key(②) as shown above.
Step 4 Insert the Back Support Bar(B) into the Side Panel(A). Step 5 A Attach the Back Support Bar(B) to the Side Panel(A) using Bolt(①) with Allen Key(②). Do not fully tighten Bolt.
Step 6 Insert the Leg Support Bar(D) into the Back Support Bar(B) and Seat Panel(C) as shown above.
Step 7 7.1) Attach the Leg Support Bar(D) to Back Support Bar(B) and Seat Panel(C) using Bolts(①) with Allen Key(②) as shown above. 7.2) Attach the Leg Support Bar(D) to Seat Panel(C) using Bolt(①) with Allen Key(②) as shown above. Do not fully tighten Bolts.
Stand the Sofa up. Place the Sofa on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and carefully, sit onto to the Sofa. This will help to align all parts at all the joints. Then get off the Sofa, and in a sequential manner, proceed to tighten all Bolts. When tightening the Bolts, tighten sequentially. DO NOT tighten any Bolt fully and then move on to the next one. This may cause the frame to warp.
Caution: You must read this before you proceed Table Label Description QTY A Left Leg 1 B Right Leg 1 C Table Top Frame (with Suction Cups) 1 D Glass Top 1 Description QTY E Bolt:M6*20MM 9 F Allen Key 1 Label Picture Picture
Before Beginning Assembly: Step 1 Take out the silders in the four ends of Table Top Frame(C ) using Allen Key(F).
Step 2 Open the carton and place all the parts on a clean, non-marring surface. Attach the Table Top Frame(C) to the Left Leg(A) using Bolt(E) and Allen Key(F) as shown in the picture. Loosely tighten the Bolts. Caution: The Table and its Parts are Heavy. Two adults are required for lifting and moving them. Step 3 Attach the Table Top Frame(C) to the Right Leg(A) using Bolt(E) and Allen Key(F) as shown in the picture. Loosely tighten the Bolts. Caution: The Table and its Parts are Heavy.
Step 4 Stand up the table, check stability and then tighten the bolts. Note DO NOT fully tighten a BOLT in one go and then move on to the next. Rather, In a sequential manner, gradually tighten each Bolt until all bolts are evenly secured. This methodology will ensure maximum evenness once all Bolts are fully tightened. Step 5 Place the Glass Top(D) on the assembled Table Frame. Caution: The Table and its Parts are Heavy. Two adults are required for lifting and moving them.
Caution : You must read this before you proceed Chaise Lounge CAUTION : This Lounge is NOT a TOY. Keep your child / children at bay during the assembly process.
Before Beginning Assembly: Overview Back Leg (C) Front Leg (A) Seat Panel (B) FRONT FACING This Chaise Lounge has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Chaise Lounge parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean, non-marring surface. Remove the plastic plugs ( prevent the alum tube was scratched) from the four ends of the Seat Panel(B) using Allen Key(②) as shown above. Place the Seat Panel(B) with its inside facing up.
Step 3 3.1) Attach the Back Leg(C) to the Seat Panel(B) using Bolts(①) with Allen Key(②) as shown above. 3.2) Attach the Back Leg(C) to the Seat Panel(B) using Bolts(①) with Allen Key(②) as shown above. Do not fully tighten Bolts.
Step 5 5.1) Attach Front Leg(C) to Seat Panel(B) using Bolts(①) with Allen Key(②) as shown above. 5.2) Attach Front Leg(C) to Seat Panel(B) using Bolts(①) with Allen Key(②) as shown above. Do not fully tighten Bolts. Step 6 Stand the Chaise Lounge up. Place the Chaise Lounge on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and carefully, sit onto to the Chaise Lounge. This will help to align all the parts at all joints.
Do not put hot items directly on furniture surface Do not clean furniture with harsh cleansers or polish. To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct sunlight is recommended. Children should not climb or jump on the furniture. Do not write on furniture without a padded barrier to protect the surface. To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine.
Caution : You must read this before you proceed Chair Label Picture Description QTY A Right Armrest/Leg 1 B Left Armrest/Leg 1 C Seat 1 D Backrest 1 Page 1 OF 5
Label Picture Description QTY ① Bolt (M6*20MM) 5 ② Bolt (M6*35MM) 7 ③ Bolt (M6*20MM) 5 ④ Allen Key 1 Before Beginning Assembly: Overview Backrest(D) Left Armrest/Leg(B) Seat(C) Right Armrest/Leg(A) FRONT FACING This Chair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Chair parts, the above picture is to help you put the various parts into perspective.
Step 1 Step 1.1 Step 1.2 Open the carton and place all the parts onto a clean, non-marring surface. 1.1) Attach Seat(C) to Right Armrest/Leg(A) using Bolts(①) with Allen Key(④) as shown above. 1.2) Attach Seat(C) to Right Armrest/Leg(A) using Bolts(②) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Step 2 Attach Backrest(D) to Right Armrest/Leg(A) using Bolts(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts.
Step 3 Step3.2 Step3.1 Step3.3 3.1) Attach the Left Armrest/Leg(B) to Backrest(D) using Bolts(③) with Allen Key(④) as shown above. 3.2) Attach the Left Armrest/Leg(B) to Seat(C) using Bolts(①) with Allen Key(④) as shown above. 3.3) Attach the Left Armrest/Leg(B) to Seat(C) using Bolts(②) with Allen Key(④) as shown above. Do not fully tighten Bolts. Step 4 Stand the Chair up. Place the Chair on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected.
Do not put hot items directly on furniture surface Do not clean furniture with harsh cleansers or polish. To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct sunlight is recommended. Children should not climb or jump on the furniture. Do not write on furniture without a padded barrier to protect the surface. To obtain the longest lifespan of your outdoor products, avoid extended and lengthy exposure to rain, snow, and direct sunshine.
