Use and Care Manual

ManualsBrandsNoble House ManualsGazebos9.83 ft. x 9.83 ft. White Aluminum Canopy Gazebo with Water-Resistant Fabric Curtains

Caution : You must read this before you proceed

Gazebo

Read all instructions before assembling and using this product

1. Select ideal location. Set out all parts on a clear and level surface prior to assembly.

Ideally, the Gazebo should be set up in the desired location to avoid moving it after

assembly.

2. Team Work. We recommend 4-5 adults and it may require 3 to 4 hours to fully assemble

the Gazebo. If possible, please use safety ladders.

3. Use caution. During the entire assembly process, especially when lifting heavy or large

parts or using ladders, pay attention to safety. No one other than the adult assistants should

be allowed in the work area.

4. Check all available parts. Before assembling your Gazebo Frame, make sure that you

have all the parts described in the Parts List.

5. Ensure that ALL BOLTS are fully and securely tightened before you proceed to attach the

Canopies.

6. Keep children away. Children shouldn’t be allowed in the work area. Do not let them

handle parts and tools. Do not allow children to climb the Gazebo.

Noble House Home Furnishings LLC Page 1 OF 16

Summary of content (16 pages)

PAGE 1
Caution : You must read this before you proceed Read all instructions before assembling and using this product 1. Select ideal location. Set out all parts on a clear and level surface prior to assembly. Ideally, the Gazebo should be set up in the desired location to avoid moving it after assembly. 2. Team Work. We recommend 4-5 adults and it may require 3 to 4 hours to fully assemble the Gazebo. If possible, please use safety ladders. 3. Use caution.
PAGE 2
Label Picture Description QTY A Column 4 B Left Short Beam 4 C Right Short Beam 4 D Long Corner Roof Bar 4 E Short Roof Bar 4 F Left Roof Finishing Bar 4 G Right Roof Finishing Bar 4 H Connection Piece 12 I Left Roof Support Bar 4 J Right Roof Support Bar 4 K Left Roof Panel (Upside) 4 L Right Roof Panel (Upside) 4 M Left Roof Panel (Downside) 4 N Right Roof Panel (Downside) 4 O Bar Union 4 P Corner Cover 4 Noble House Home Furnishings LLC Page 2 OF 16
PAGE 3
Q Joint Cover Plate 4 R Outside Roof Connector 1 S Inside Roof Connector 1 T Base 4 U Track 8 V Mosquito Netting 4 W Curtain 4 X Finishing End 4 Y Corner Finishing End 4 Z Hook 112 Description QTY ① Screw (ST5*10mm) 33 ② Bolt (M5*10mm) 13 ③ Bolt (M6*12mm) 9 ④ Bolt (M6*15mm) 136 ⑤ Bolt (M6*30mm) 17 ⑥ Screwdriver 1 ⑦ Allen Key 1 ⑧ Stake 12 ⑨ Washer 163 Label Picture Noble House Home Furnishings LLC Page 3 OF 16
PAGE 4
Before Beginning Assembly: x4 x4 x4 x4 x4 x8 x4 x4 x4 x4 x4 x4 x4 x4 x4 x4 x4 x4 x4 x1 x1 x4 x4 x4 x112 x163 Noble House Home Furnishings LLC x13 x9 x12 x8 x33 x1 x136 x17 x1 Page 4 OF 16
PAGE 5
Overview Outside Roof Connector(R) Roof Panel(K) Long Corner Roof Bar(D) Roof Support Bar(J) Roof Panel(L) Connection Piece(H) Roof Panel(M) Roof Panel(N) Left Short Beam(B) Roof Support Bar(I) Short Roof Bar(E) Right Short Beam(C) Curtains(W) Columns(A) Mosquito Netting(V) This Gazebo has multiple parts and may require up to 3 hours to assemble. To give you an overview of the Gazebo parts, the above picture is to help you put the various parts into perspective.
PAGE 6
Step 1 A A T T Attach Columns(A) onto Bases(T) using Bolts(②) and Washers(⑨) with Screwdriver(⑥). Tighten the Bolts fully in a sequential manner. Step 2 C B ④+⑨ O ④+⑨X6 Attach Bar Union(O) between Left Short Beam(B) and Right Short Beam(C) using Bolts(④) and Washers(⑨) with Allen Key(⑦). Note: Ensure the mounting postions of Bar Union(O) match the Left Short Beam(B) and Right Short Beam(C) mounting positions before assembling Bolts.
PAGE 7
Step 3 C A 3.1 B C A A Inside ⑤+⑨ B C 3.2 C C B C B ⑤+⑨ B Outside C B A C B 3.3 B B C B ③ ③ C Note: Please place a blanket or carton on the floor before assembly to protect surfaces from cuts and abrasions. 3.1) Attach column inside: Left Short Beam(B), Right Short Beam(C) and Columns(A) using Bolts(⑤) and Washers(⑨) with Allen Key(⑦).Repeat once and then set aside. 3.
PAGE 8
Step 4 B C C B B C C B C P B Q ① ① C B C B ① ① 4.1) Attach Corner Covers(P) to Left Short Beams(B) and Right Short Beams(C) using Screws(①) with Screwdriver(⑥). 4.2) Attach Joint Covers(Q) on the outside of Left Short Beams(B) and Right Short Beams(C) using Screws(①) with Screwdriver(⑥). Tighten the Screws fully in a sequential manner. Note: Please use a ladder, if you can't reach it.
PAGE 9
Step 5 5.1 U Z 5.2 U U 5.1) Slide seven Hooks(Z) into each Track(U). Note: There are a total of 14 Hooks in each Track(U) 5.2) Attach Tracks(U) to the inside of Left Short Beams(B) and Right Short Beams(C) using Bolts(④) and Washers(⑨) with Allen Key(⑦). Repeat this process with the remaining Tracks. Tighten the Bolts fully in a sequential manner.
PAGE 10
Step 6 B C C B A B B C C A A A B C ④+⑨ H ④+⑨ H A H ④+⑨ Attach Connection Piece(H) between Left Short Beam(B) and Right Short Beam(C) using Bolts(④) and Washers(⑨) with Allen Key(⑦). Attach Connection Piece(H) between Left Short Beam(B) and Column(A) using Bolts(④) and Washers(⑨) with Allen Key(⑦). Attach Connection Piece(H) between Right Short Beam(C) and Column(A) using Bolts(④) and Washers(⑨) with Allen Key(⑦). Tighten the Bolts fully in a sequential manner.
PAGE 11
Step 7 R UP S D 7.1 E E S inside E 7.2 E 7.3 7.1) Attach two Short Roof Bars(E) one at a time to the inside Roof Connector(S) using Bolts(④) and Washers(⑨) with Allen Key(⑦) as picture above. 7.2) Attach the same Short Roof Bars(E) to the middle of the Left Short Beams(B) and Right Short Beams(C) using Bolts(④) and Washers(⑨) with Allen Key(⑦) as picture above. 7.3) Finally, attach the remaining Short Roof Bars(E) to the inside Roof Connector(S) using Bolts(④) and Washers(⑨) with Allen Key(⑦).
PAGE 12
Step 8 8.1 D D D D D B D C C B D D D B C R 8.2 R S 8.1) Attach Long Corner Roof Bars(D) to Inside Roof Connector(S) using Bolts(④) and Washers(⑨) with Allen Key(⑦). Then, attach Long Corner Roof Bars(D) to Columns(A) using Bolts(④) and Washers(⑨) with Allen Key(⑦). 8.2) Last attach the Outside Roof Connector(R) to Inside Roof Connector(S) using Bolt(④) and Washer(⑨) with Allen Key(⑦). Tighten the Bolts fully in a sequential manner.
PAGE 13
Step 9 Roof Panel: Thick Face Up, Thin Face Down K I D E L J D E K D K L I J D I L J E From the end of the Long Corner Roof Bars(D), insert Roof Panel(K) and Roof Panel(L) into the Roof Bar's upper tracks as pictured above. Note: Ensure they are completely inserted in the tracks. Then, insert the Roof Support Bar(I) and Roof Support Bar(J) into the Roof Bar's upper tracks as pictured above. Note: Please remove the white protective film from the Panels before assembly.
PAGE 14
Step 10 M N F G D E F ④+⑨ G Y F G X ④+⑨ Insert the Roof Panel(M) and Roof Panel(N) into the Roof Bar's bottom tracks as pictured above. Note: Ensure they are completely inserted in the tracks. Insert the Roof Finishing Bar(G) and Roof Finishing Bar(F) into the Roof Bar's bottom tracks as pictured above. Attach Finishing End(X), Roof Finishing Bar(G) and Roof Finishing Bar(F) to Roof Bar(E) using Bolt(④) and Washer(⑨) with Allen Key(⑦).
PAGE 15
Step 11 W W W V W V U Z W V ⑧X3 11.1) Install the Mosquito Netting(V) along the inside Tracks(U) on the Hooks(Z). 11.2) Install the Curtains(W) along the outside Tracks(U) on the Hooks(Z). 11.3) Affix the Gazebo to the ground by inserting the Stakes(⑧) through the Bases(T). Your Gazebo is ready for use. This Gazebo can only be used on a flat, level surface. CAUTIONS: 1. Check stability and then tighten the Bolts. 2. DO NOT tighten any Bolts fully and then move on towards the next one.
PAGE 16
What is Proposition 65? Proposition 65 is a California law that requires warning labels on products that may contain one of more than 800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment (OEHHA) has deemed to cause cancer or other reproductive toxicity.