Caution : You must read this before you proceed TABLE CAUTION : This Table is NOT a TOY. Keep your child / children at bay during the assembly process. For moving the Table and to prevent damage to the Table, two adults are needed to execute this action.
Label Picture Description QTY A Long Legs with pre-attached Support Wing.
Label Picture Description QTY ① Short Bolt (M6 x 35mm) 5 ② Long Bolt (M6 x 55mm) 13 ③ Long Screw (M6x45) 9 ④ Screw (M4 x 20mm) (used with Screw Driver) 5 ⑤ Nut Ø6 x 6 5 ⑥ Plate for Horseshoe Bolt (125 x 15 x 2) 2 ⑦ Horseshoe Bolt Ø6 x (110 + 106 + 110) 2 ⑧ Restraint Strap 2 ⑨ Allen Key 2 ⑩ Spanner 1 ⑪ Screw Driver Noble House Home Furnishings LLC Not Provided 3 ____
Before Beginning Assembly: OVERVIEW Back Panel (F) Upper Suport Wing (H) Table Top (G) Table Support Bar (C) Footrest Shelf (E) Lower Support Wing (B) FRONT FACING Long Legs (A) Short Leg (D) This Table has multiple parts and may require up to some 30 minutes to assemble. To give you an overview of the Table, the above picture aims help you put the various parts into perspective. Please read through the instructions here below to familiarise the parts and steps before assembly.
Step 1 Unpack and place all parts on a clean, non-marring surface. Step 2 Customer need to check the railing height, matching to table height, before assembly of Lower Support Wing (B). Attached Long Legs ( A ) with pre- fixed wooden dowel to the Lower Support Wing (B) using Short Bolt (②) and Allen Key (⑨). Repeat the same process with the other Long Leg ( A ) DO NOT FULLY TIGHTEN THE BOLTS.
Step 3 Customer need to check the railing height before assembly the part C. Attached Table Support Bar ( C ) with Long Legs ( A ) using Short Bolt (①) and Allen Key (⑨) as shown in picture. Upon completion - place aside. DO NOT FULLY TIGHTEN THE BOLTS. Step 4 Using Screw Driver (⑪ ) and Screws (④) to assemble the Short Leg ( D ) to the Footrest Shelf ( E ) as shown in picture. Upon completion of assembly - place aside.
Step 5 Lay down pre-fixed table in step 3 Assemble pre-fixed table in step 3 and step 4 together by using Long Bolts (②) and Allen Key (⑨) as shown in picture. DO NOT FULLY TIGHTEN THE BOLTS. Step 6 Assembly the Table Top ( G ) to the Back Panel ( F ) by using Allen Key (⑨) to tighten the Long Screws (③) in. DO NOT FULLY TIGHTEN THE SCREWS.
Step 7 Assembly Upper Support Wings (H) to finish part in Step 6 by using Long Screws (③) and Allen Key (⑨) as shown in picture . Upon completion - place aside. DO NOT FULLY TIGHTEN THE SCREWS. Step 8 With assistance from your adult partner, stand pre-fixed table in Step 5, right side up. Attach the Table Support Bar (C) to your balcony (railing) by using Horseshoe Bolt (⑦), Plate (⑥), Nut (⑤) and Spanner (⑩) as shown in picture.
Step 9 Railing Assemble pre-fixed table from Step 7 and Step 8 together by using Long bolts (②) and Allen key (⑨) as shown in picture. DO NOT FULLY TIGHTEN THE BOLTS. Step 10 Railing Next, place your arms onto the table top and EXERT pressure, floorwards. This pressure will help all parts reach alignment at all joints. Check for wobbles. In a sequential manner, gradually tighten all Bolts/Screws until evenly secured. Inspect the Table and make sure all parts are adequately connected.
Questions & Answers about Proposition 65 • What is Proposition 65? Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. These chemicals can be in the products that Californians purchase, in their homes or workplaces, or that are released into the environment.