Caution : You must read this before you proceed Chair Label Picture Description QTY A Right Armrest 1 B Left Armrest 1 C Seat 1 D Backrest 1 E Seat Cushion 1 F Back Cushion 1 Noble house Home Furnishings LLC Page 1 OF 17
Label Picture Description QTY ① Bolt (M6*35MM) 9 ③ Washer 9 ④ Allen Key 1 Before Beginning Assembly: X9 X9 Back Cushion(F) Left Armrest(B) Seat Cushion(E) Backrest(D) Right Armrest(A) Seat(C) FRONT FACING This Chair has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Chair parts, the above picture is to help you put the various parts into perspective.
Step 1 Open the carton and place all the parts onto a clean, non-marring surface. Place the Left Armrest(A) facedown. Attach Seat(C) to Left Armrest(B) using Bolts(①) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Step 2 Attach Seat(C) to Right Armrest(A) using Bolts(①) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Step 3 Stand the Chair up.
Step 4 Place the Chair on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and carefully sit onto the Chair. This will help to align all parts at all joints.Then get off the Chair, and in a sequential manner, proceed to tighten all Bolts. When tightening the Bolts, tighten sequentially. DO NOT tighten any Bolt fully and then move on to the next one. This may cause the frame to warp. If there are still wobbles, loosen the Bolts and execute this same process.
Noble house Home Furnishings LLC Page 5 OF 17
Caution : You must read this before you proceed Loveseat Label Picture Description QTY G Right Armrest 1 H Left Armrest 1 I Seat 1 J Backrest 1
K Seat Cushion 1 L Back Cushion 1 Description QTY ① Bolt (M6*35MM) 9 ② Bolt (M6*25MM) 2 ③ Washer 11 ④ Allen Key 1 Label Picture Before Beginning Assembly: X9 X2 X11
Overview Back Cushion(L) Backrest(J) Left Armrest(H) Right Armrest(G) Seat Cushion(K) Seat(I) FRONT FACING This Loveseat has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Loveseat parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Open the carton and place all the parts onto a clean, non-marring surface.
Step 2 Attach Seat(I) to Right Armrest(G) using Bolts(①) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Step 3 Attach Backrest(J) to Right Armrest(G) and Left Armrest(H) using Bolts(①) and Washers(③) with Allen Key(④) as shown above. Attach Backrest(J) to Seat(I) using Bolt(②) and Washer(③) with Allen Key(④) as pictured. Do not fully tighten the Bolts.
Step 4 Place the Loveseat on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and carefully sit onto the Loveseat. This will help to align all parts at all joints.Then get off the Loveseat, and in a sequential manner, proceed to tighten all Bolts. When tightening the Bolts, tighten sequentially. DO NOT tighten any Bolt fully and then move on to the next one. This may cause the frame to warp. If there are still wobbles, loosen the Bolts and execute this same process.
Caution : You must read this before you proceed Glass Table Label Description QTY N Leg 2 O Table Top Frame 1 M Glass Top 1 Description QTY Bolt (M6*20MM) 9 Label 5 Picture Picture
③ Washer 9 ④ Allen Key 1 Before Beginning Assembly: X9 X9 Overview Table Top Frame(O) Glass Top(M) Leg(N) FRONT FACING This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Table parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 1 Open the carton and place all the parts onto a clean, non-marring surface. Place the Table Top Frame(O) facedown. Attach Leg(N) to Table Top Frame(O) using Bolts(⑤) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts. Step 2 Attach Leg(N) to Table Top Frame(O) using Bolts(⑤) and Washers(③) with Allen Key(④) as shown above. Do not fully tighten the Bolts.
Step 3 Place the Table on a LEVEL SURFACE. Inspect it and make sure all parts are adequately connected. Gently and carefully push down onto the Table with your hands. This will help to align all parts at all joints.Then get off the Table, and in a sequential manner, proceed to tighten all Bolts. When tightening the Bolts, tighten sequentially. DO NOT tighten any Bolt fully and then move on to the next one. This may cause the frame to warp.
Step 5 Your Table is ready for use. This Table can only be used on a flat, level surface.