Caution : You must read this before you proceed Bar Stool / Counter Stool
Label Description QTY A Wooden Legs 4 pcs B Leg Frame 1 pc C Swivel Plate 1 pc D Cushion Seat 1 pc Description QTY ① Bolt : M6 x 40mm 4 pcs ② Bolt : M6 x 35mm 8 pcs ③ Bolt : M6 x 25mm 4 pcs ④ Spring Washer M6 x 13mm 12 pcs ⑤ Flat Washer M6 x 13mm 12 pcs ⑥ Flat Washer M6 x 16mm 4 pcs ⑦ Allen Key 1 pc Label Picture Picture
Before Beginning Assembly : 4 Bolt M6 x 40mm Pack A - for 4 Spring Washer M6 x 13mm assembling the 4 Flat Washer M6 x 13mm Wooden Leg (A) to 1 Allen Key the Leg Frame (B) 8 Bolt M6 x 35mm Pack B - for 8 Spring Washer M6 x 13mm assembling the 8 Flat Washer M6 x 13mm Wooden Leg (A) to the Swivel Plate (C) Pack C - for 4 Bolt M6 x 25 mm assembling the 4 Flat Washer M6 x 16mm Swivel Plate (C) to the Cushion Seat (D)
Overview Cushion Seat (D) Swivel Plate (C) Wooden Leg (A) Leg Frame (B) FRONT FACING This Bar Stool/Counter Stool has multiple parts and may require up to 30 minutes to assemble. To give you an overview of the Bar Stool/Counter Stool parts, the above picture is to help you put the various Bar Stool/Counter Stool parts into perspective. Please read through the instructions to familiarise yourself with the parts and steps before assembly. Step 1 B.Leg Frame A.Wooden Legs C.Swivel Plate D.
Step 2 Pack A Place the Wooden Leg (A) and Leg Frame (B) on a clean, non-marring surface to avoid any scratch or damage to the product. Pick up one Wooden Leg (A) and align to the notch at the Leg Frame (B). use the Bolt , Spring Washer , Flat Washer , Allen Key by using Hardware Pack A. Repeat the same process with the remaining legs. At this stage, DO NOT FULLY TIGHTEN. WARNING ! OVER TIGHTEN COULD LEAD TO DAMAGE OF THE PRODUCT .TIGHTEN ONLY UNTIL SECURE AND STABLE. Step 3 3.1 3.2 Pack B 3.
Step 4 4.1 4.2 4.1 Place asembled Swivel Plate (C) upside down to the seat frame,as shown above. 4.2 Turn the Swivel Plate (C) to 45° degree position as shown above. Align the mounting Position of the Swivel Plate (C) to the the mounting Position of the Seat Frame. Affix the Swivel Plate (C)with the Bolt l , Flat Washer ⑥ and Allen Key ⑦by using Hardware Pack C. Partially Screw in these four Bolts into the Swivel Plate (C). Turn in all the Bolts. At this stage, FULLY TIGHTEN THE BOLTS.
Step 5 CAUTION DO NOT put fingers into the seat gap Ensure that all the Bolts are fully driven in and locked in. Turn this Bar Stool/Counter Stool right way up and ensure this Bar Stool/Counter Stool is stable. Place the Bar Stool/Counter Stool on a level Surface to check if it wobbles. If it is wobbles, lift the Bar Stool/Counter Stool some 30cm to 50 cm high from the ground. Keep your feet and toes well away from the drop zone.
