G3500 V2.0 User Guide DANGER PRIOR TO USE, READ AND UNDERSTAND PRODUCT SAFETY INFORMATION. Failure to follow the instructions may result in ELECTRICAL SHOCK, EXPLOSION, or FIRE, which may result in SERIOUS INJURY, DEATH, DAMAGE TO DEVICE or PROPERTY. Do not discard this information. Welcome. Thank you for buying the NOCO Genius® G3500. Read and understand the User Guide before operating the charger. For questions regarding our chargers, view our comprehensive support information at www.no.co/support.
Contacting NOCO. Phone: 1.800.456.6626 Email: support@no.co Mailing Address: 30339 Diamond Parkway, #102 Glenwillow, OH 44139 United States of America About G3500.The NOCO Genius® G3500 represents some of the most innovative and advanced technology on the market, making each charge simple and easy. It is quite possibly the safest and most efficient charger you will ever use.
indicated on the charger by a red line. It is important to understand the differences and purpose of each charge mode. Do not operate the charger until you confirm the appropriate charge mode for your battery. Below is a brief description: Mode Standby Explanation In Standby mode, the charger is not charging or providing any power to the battery. Energy Save is activated during this mode, drawing microscopic power from the electrical outlet. When selected, an orange LED will illuminate.
Mode Explanation 6V NORM For charging 6-volt Wet Cell, Gel Cell, Enhanced Flooded, Maintenance-Free and Calcium batteries. When selected, a white LED will illuminate. Press & Hold 12V LITHIUM 7.25V | 3.5A | 2-120Ah Batteries For charging 12-volt lithium-ion batteries, including lithium iron phosphate. When selected, a blue LED will illuminate. Press & Hold 14.2V | 3.
BATTERIES MAY BE UNSTABLE AND UNSUITABLE FOR CHARGING. Using 12V Repair. [Press & Hold] 12V Repair is an advanced battery recovery mode for repairing and storing, old, idle, damaged, stratified or sulfated batteries. Not all batteries can be recovered. Batteries tend to become damaged if kept at a low charge and/or never given the opportunity to receive a full charge. The most common battery problems are battery sulfation and stratification.
1.) Connect the positive (red) battery clamp or eyelet terminal connector to the positive (POS,P,+) battery terminal. 2.) Connect the negative (black) battery clamp or eyelet terminal connector to the negative (NEG,N,-) battery terminal or vehicle chassis. 3.) Connect the battery charger’s AC power plug into a suitable electrical outlet. Do not face the battery when making this connection. 4.
Understanding Charge LEDs. The charger has four (4) Charge LEDs - 25%, 50%, 75% and 100%. These Charge LEDs indicate the connected battery(s) state-of-charge (SOC). See the explanation below: LED Explanation 25% Red LED The 25% Charge LED will slowly pulse “on” and “off”, when the battery is less than 25% fully charged. When the battery is 25% charged, the red Charge LED will be solid.
Understanding Advanced Diagnostics. Advanced Diagnostics is used when displaying Error Conditions. It will display a series of blink sequences that help you identify the cause of the error and potential solutions. All Error Conditions are displayed with the Error LED and Standby LED flashing back and forth. The number of flashes between each pulse denotes a potential Error Condition (except reverse polarity and low-voltage battery). Error Reason/Solution Single Flash Battery will not hold a charge.
Memory Returns to last selected mode when restarted Interactive Alters the charging process based on organic battery feedback Recovery Applies a high-voltage pulse charge when low-voltage, sulfation or lost capacity is detected Safe Protects against reverse polarity, sparks, overcharging, overcurrent, open-circuits, short-circuits and overheating Fast Charges two times faster than traditional battery chargers Compensation Adjusts for varying A/C line voltage for consistent charging Rugged Dirt, water,
Optimization Stabilizes internal battery chemistry for increased performance and longevity Maintenance Plus Keeps the battery fully charged without overcharging allowing the charger to be safely connected indefinitely Energy Save Minimizes energy consumption when full power is not needed Load Tracking Charge LEDs dynamically track the batteries state-of-charge when a load outpaces the charge current Diagnostics Intuitive visual diagnostic tool for detecting reverse polarity, low-voltage or damaged batte
Charging Steps. Voltage (V) Step Current (A) 2 3 4 5 6 7 8 Di An aly z ag e no Re se co ve In ry itia liz e Ab Bu so lk r O pt ptio im n M iza ain tio n te na nc e 1 Step 1 & 2: Analyze & Diagnose Checks the battery’s initial condition, including voltage, state-of-charge and health, to determine if the battery is stable before charging. Step 3: Recovery Initializes the Recovery desulfation process (if needed) for deeply discharged or sulfated batteries by pulsing small amounts of current.
Step 8: Maintenance Continuously monitors the battery to determine when a maintenance charge should be initiated. If the battery voltage falls below its target threshold, the charger will restart the Maintenance cycle until voltage reaches its optimal state and then discontinues the charge cycle. The cycle between Optimization and Maintenance is repeated indefinitely to keep the battery at full charge. The battery charger can be safely left connected indefinitely without the risk of overcharging.
Technical Specifications. Input Voltage AC: Working Voltage AC: Efficiency: Power: 110-120 VAC, 50-60Hz 85-130 VAC, 50-60Hz 85% Approx. 60W Max Charging Voltage: Various Charging Current: 3.5A (12V & 6V), .
G3500 V2.0 Manuel d’utilisation DANGER AVANT TOUTE UTILISATION VEUILLEZ LIRE ET COMPRENDRE LES INDICATIONS DE SÛRETÉ.Ne pas respecter ces instructions peut conduire à un CHOC ÉLECTRIQUE, UNE EXPLOSION, UN INCENDIE pouvant causer des BLESSURES GRAVES, LA MORT ou ENDOMMAGER L’APPAREIL ou d’autres OBJETS. N’ignorez pas les informations contenues ici. Bienvenue. Merci pour l’achat d’un NOCO Genius® G3500. Veuillez lire et comprendre le manuel d’utilisation avant d’utiliser l’appareil.
Contacter NOCO. Téléphone : 1.800.456.6626 E-Mail : support@no.co Adresse postale : 30339 Diamond Parkway, #102 Glenwillow, OH 44139 United States of America À propos de G3500. Le NOCO Genius® G3500 dispose des technologies parmi les plus innovantes et avancées du marché, rendant chaque chargement simple et facile. C’est très probablement un des chargeurs les plus sûrs et les plus efficaces que vous utiliserez.
toute votre attention avant de les déclencher. “Appuyer et charger” sont indiqués sur le chargeurs sur une ligne rouge. Il est important de comprendre les différences et les avantages de chaque mode de chargement. Il est important de charger jusqu’à ce que vous confirmiez le mode de chargement de votre batterie. Ci-dessous se trouve une brève description : Modo Veille Explication En mode veille, le chargeur ne charge pas ou ne fournit aucune électricité à la batterie.
Modo Explication NORME 6V Pour charger une batterie humide, à gel, EFB (enhanced flooded battery), sans entretien et au calcium. Lorsqu’il est choisi, un LED blanc s’allume. Appuyer & maintenir LITHIUM 12V Appuyer & maintenir RÉPARATION 12 V Appuyer & maintenir 7.25V | 3.5A | 2-120Ah Batteries Pour charger des batteries 12 volt lithium-ions, y compris lithium fer phosphate. Lorsqu’il est choisi, un LED bleu s’allume. 14.2V | 3.
DE GESTION DE BATTERIES (BMS). CONSULTEZ LE FABRICANT DE BATTERIES LITHIUM AVANT DE CHARGER ET RENSEIGNEZ-VOUS SUR LES TAUX DE CHARGEMENT ET DE TENSION. CERTAINES BATTERIES LITHIUM-IONS PEUVENT ÊTRE INSTABLES ET INADAPTÉES AU CHARGEMENT. Utilisation du mode de réparation 12V. Appuyer & maintenir Le mode batterie de réparation 12V de récupération pour réparer, sauvegarder et stocker des batteries sulfatées ou stratifiées, vieilles, inutilisées ou endommagées.
Connecter la batterie. Ne connectez pas la prise de courant AC jusqu’à ce que toutes les autres connections soient faites. Identifiez la bonne polarité des bornes de la batterie sur la batterie. La borne positive de la batterie est généralement indiquée par ces lettres ou symboles (POS, P, +). La borne négative de la batterie est généralement indiquée par ces lettres ou symboles (NEG, N, -). Ne connectez pas le carburateur, les conduites de carburant, ou bien des parties fines en métal.
5.) Les LEDs correspondant au mode de chargement s’allumeront, ainsi que les LEDs indiquant la progression du chargement (selon l’état de la batterie). 6.) Le chargeur peut maintenant rester connecté à la batterie à tout moment pour fournir un chargement d’entretien. Comprendre les diagnostics avancés. Les diagnostics avancés sont utilisés pour afficher les états d’erreur.
Comprendre les LEDs de chargement. Le chargeur dispose de quatre (4) LEDs de chargement -25%, 50%, 75% et 100%. Ces LEDs de chargement indiquent l’état de chargement (state of charge SOC) de la ou les batteries connectées.
Mémoire Revient au dernier mode sélectionné lorsqu’elle est redémarrée Interaction Modifie le processus de chargement en se basant sur le retour organique de la batterie Rétablissement Donne une pulsation de chargement de haute tension lorsque est détecté une tension basse, un sulfatage ou une perte de capacité Sécurité Protection contre une polarité inversée, des étincelles, un surchargement, une surintensité, une sous-tension et une surchauffe Rapidité Charge deux fois plus vite que des chargeurs trad
Murs coupe-feu Barrières de sécurité de plusieurs niveaux empêchant les conditions d’utilisation anormales et peu sûres Optimisation Stabilise la composition chimique interne de la batterie pour une performance et une longévité augmentée Entretien Plus Maintient la batterie pleinement chargée sans la surcharger, permettant au chargeur d’être branché sur le secteur en permanence en toute sécurité Économie d’énergie Adapte la consommation d’énergie au besoin réel Suivi du chargement Les LEDs de chargement
Étapes de chargement. 2 4 6 7 8 tio n Vr so ac r O pt ptio im n isa t En ion tre tie n 5 isa aly s D An 3 Ré iagn e ta os bl iss tic e In me itia nt l 1 Ab Tension (V) Étape Courant (A) Étape 1 & 2 : Analyse & Diagnostic Vérifie l’état initial de la batterie, y compris la tension, l’état du chargement et le cycle de vie pour déterminer si la batterie est apte à être chargée.
d’avoir une durée de cycle et une performance optimisées. Le chargeur basculera en mode entretien si la batterie indique au chargeur qu’elle nécessite plus de courant. Étape 8 : Entretien Supervise en continu la batterie pour vérifier si une charge d’entretien doit être initiée. Si la tension de la batterie tombe en-dessous du seuil-cible, le chargeur redémarrera le cycle d’entretien jusqu’à ce que la tension atteigne son état optimal, puis le cycle de charge s’interrompt.
Spécifications techniques Tension d’entrée AC: 110-120 VAC, 50-60Hz Working Voltage AC: 85-130 VAC, 50-60Hz Efficacité: Puissance: 85% Anviron. 60W Max Tension de chargement: Divers Courant de chargement: 3.5A (12V & 6V), .
G3500 Guía de usuario V2.0 PELIGRO ANTES DE USAR, ASEGÚRESE DE QUE LEE Y ENTIENDE TODA LA INFORMACIÓN DE SEGURIDAD DEL PRODUCTO. El incumplimiento de las instrucciones podría resultar en DESCARGA ELÉCTRICA, EXPLOSIÓN o INCENDIO, que podrían causar LESIONES GRAVES, MUERTE o DAÑOS MATERIALES o AL DISPOSITIVO. No tire esta información. Bienvenido. Gracias por comprar NOCO Genius® G3500. Asegúrese de que lee y entiende la guía de usuario antes de usar el cargador.
Contacte con NOCO. Teléfono: 1.800.456.6626 Correo electrónico: support@no.co Dirección postal: 30339 Diamond Parkway, #102 Glenwillow, OH 44139 United States of America Acerca de G3500. El NOCO Genius® G3500 incorpora de la más innovadora y avanzada tecnología del mercado, lo que simplifica y facilita cada carga. Es posiblemente el cargador más seguro y eficaz que utilizará jamás.
su atención completa antes de ser seleccionados. Los modos “Press and Hold” se indican en el cargador con una línea roja. Es importante entender las diferencias entre los distintos modos de carga y el propósito de cada uno. No haga funcionar el cargador hasta que haya confirmado el modo de carga adecuado para su batería. A continuación se muestra una breve descripción: Modo Standby 12V NORM 12V COLD/ AGM Explicación En el modo Standby, el cargador no está cargando o suministrando energía a la batería.
Modo Explicación 6V NORM Para cargar baterías de 6 V húmedas, de gel, con tecnología EFB, de libre mantenimiento y de calcio. Al seleccionar este modo de carga se iluminará un led blanco. pulse continuamente 12V LITHIUM pulse continuamente 12 V REPAIR pulse continuamente 7.25V | 3.5A | 2-120Ah Batería Para cargar baterías de ión de litio de 12 V, incluidas baterías con tecnología LFP (litio hierro fosfato). Al seleccionar este modo de carga se iluminará un led azul. 14.2V | 3.
FORMAS Y PUEDE QUE ALGUNAS NO CONTENGAN UN SISTEMA DE CONTROL DE LA BATERÍA. CONSULTE CON EL FABRICANTE DE LA BATERÍA DE LITIO ANTES DE CARGARLA Y AVERIGÜE CUÁLES SON LOS NIVELES DE CARGA Y VOLTAJES RECOMENDADOS. ALGUNAS BATERÍAS DE IÓN DE LITIO PUEDEN SER INESTABLES Y NO APTAS PARA CARGAR. Cómo usar 12V Repair.
Conexión a la batería. No conecte el cable de alimentación de corriente alterna hasta que haya hecho el resto de las conexiones. Averigüe la polaridad correcta de los terminales en la batería. El polo positivo de la batería está marcado generalmente con estas letras o símbolos (POS, P, +). El polo negativo de la batería está marcado generalmente con estas letras o símbolos (NEG, N, -). No establezca ninguna conexión con el carburador, las mangueras de combustible o placas delgadas de metal.
5.) El led de modo iluminará el modo de carga seleccionado y los ledes de carga LED se iluminarán (dependiendo del estado de la batería) indicando que el proceso de carga ha comenzado. 6.) Ahora el cargador se puede dejar siempre conectado a la batería para suministrar carga de mantenimiento. Diagnóstico avanzado. El diagnóstico avanzado se utiliza cuando se obtienen mensajes de error. Mostrará series de destellos que le ayudarán a encontrar la causa del error y posibles soluciones.
Significado de los ledes de carga. El cargador tiene cuatro (4) ledes de carga por entrada: 25%, 50%, 75% y 100%. Estos ledes de carga indican el estado de carga de la(s) batería(s) conectada(s). Vea la siguiente explicación: LED Explicación LED rojo 25% El led de carga 25% se encenderá y apagará lentamente cuando la carga de la batería sea inferior al 25%. Cuando la carga de la batería alcance el 25%, el led de carga se volverá rojo sólido.
Memoria Vuelve al último modo seleccionado cuando se reinicia Interactivo Modifica el proceso de carga basándose en información suministrada por la propia batería Recuperación Aplica una carga de alto voltaje cuando detecta bajo voltaje, sulfatación o pérdida de capacidad Seguro Protege contra polaridad inversa, chispas, sobrecarga, sobretensión, circuitos abiertos, cortocircuitos y sobrecalentamiento Rápido Cargas dos veces más rápido que los cargadores de batería tradicionales Compensación Se ajusta
Optimización Estabiliza la composición química interna de la batería para incrementar su rendimiento y duración Mantenimiento extra Mantiene la batería completamente cargada sin sobrecargarla y permite que el cargador quede conectado indefinidamente con toda seguridad Ahorro de energía Minimiza el consumo de energía cuando no es necesario usar la máxima potencia Seguimiento de la carga Los ledes de carga siguen el estado de carga de las baterías de forma dinámica cuando una carga supera la corriente de c
Pasos de carga. 1 2 3 4 5 6 7 8 Di An á ag lisi n s Re óst cu ico pe ra ció n In ici o C Ab arg a O sor pt c im ión M an izac te i ni ón m ien to Voltaje (V) Paso Corriente (A) Pasos 1 y 2: Análisis y diagnóstico Comprueba el estado inicial de la batería, incluido el voltaje, el estado de carga y el estado general para determinar si la batería es estable antes de cargarla.
específica de la batería. De este modo se incrementa la duración y el rendimiento de la batería. El cargador cambiará al paso de mantenimiento si la batería le indica que necesita más corriente. Paso 8: Mantenimiento Supervisa continuamente la batería para determinar cuándo deber iniciarse una carga de mantenimiento. Si el voltaje de la batería cae por debajo de su umbral objetivo, el cargador volverá a iniciar el ciclo del mantenimiento hasta que el voltaje alcance su estado óptimo.
Especificaciones técnicas. Voltaje de entrada CA: 110-120 VAC, 50-60Hz Voltaje normal de trabajo CA: 85-130 VAC, 50-60Hz Eficacia: 85% Aprox. Energía: 60W Max Voltaje de carga: Vario Drenaje de corriente: 3.
1.800.456.6626 support@no.co 30339 Diamond Parkway, #102 Glenwillow, OH 44139 United States of America no.