Installation Guide
Table Of Contents
- SAR-Hm and SAR-Hmc Chassis Installation Guide
- Table of Contents
- List of Tables
- List of Figures
- 1 Preface
- 2 Mandatory Regulations
- 2.1 In This Chapter
- 2.2 List of Terms
- 2.3 Safety Warnings / Avertissements de Sécurité
- 2.4 General Requirements
- 2.5 Safety Approvals
- 2.6 Safety Approval for External DC Sources That Power This Equipment
- 2.7 Canada Regulations
- 2.8 United States Regulations
- 2.9 European Union Regulations
- 2.10 United Kingdom Regulations
- 2.11 Australia/New Zealand Regulations
- 2.12 China Regulations
- 2.13 South Korea Regulations
- 2.14 Japan Regulations
- 2.15 Hazardous Locations
- 3 7705 SAR-Hm and 7705 SAR-Hmc Overview
- 3.1 In This Chapter
- 3.2 Overview of the 7705 SAR-Hm and 7705 SAR-Hmc
- 3.2.1 7705 SAR-Hm and 7705 SAR-Hmc Components
- 3.2.1.1 Chassis Features
- 3.2.1.2 Ethernet Ports
- 3.2.1.3 RSVD Port
- 3.2.1.4 RS-232 Ports
- 3.2.1.5 Console Port
- 3.2.1.6 Alarms Port
- 3.2.1.7 Main and Diversity Antenna Connectors
- 3.2.1.8 GPS Antenna Connector
- 3.2.1.9 WLAN Connector
- 3.2.1.10 Chassis Grounding
- 3.2.1.11 Power Supply Input
- 3.2.1.12 High Voltage Power Supply Unit
- 3.2.1.13 Chassis Temperature Control
- 3.2.1.14 Chassis Mounting Options
- 3.2.1 7705 SAR-Hm and 7705 SAR-Hmc Components
- 3.3 Cellular Components
- 3.4 GNSS Components
- 3.5 WLAN Components
- 3.6 Citizens Broadband Radio Service
- 3.7 ADP-Hm Prerequisites and Pre-staging Considerations
- 3.8 Chassis Installation Process
- Customer Document and Product Support
SAR-Hm and SAR-Hmc Chassis Installation Guide Mandatory Regulations
3HE 17810 AAAA TQZZA © 2022 Nokia. Nokia Confidential Information
Use subject to agreed restrictions on disclosure and use.
29
2.3.4 Physical Safety / Sécurité Physique
• Always keep your fingers away from rotating fan blades. Do not put your fingers
or any tool near a fan if the fans are still spinning. Allow the fans to spin down
and fully stop before servicing.
Tenez toujours vos doigts éloignés des pales du ventilateur en rotation. Ne
placez pas vos doigts ou tout autre outil à proximité d’un ventilateur s’il tourne
encore. Laissez les ventilateurs s’arrêter complètement avant l’entretien.
• Before working on equipment that is connected to power, remove jewelry, such
as rings, necklaces, and watches. When metal objects are in contact with power
and ground, serious burns can occur or the objects can become welded to the
terminals.
Avant de travailler sur un équipement connecté à l'alimentation, retirez vos
bijoux, tels que les bagues, les colliers et les montres. Lorsque des objets
métalliques entrent en contact avec l'alimentation et la terre, de graves brûlures
peuvent survenir ou les objets peuvent se souder aux bornes.
2.3.5 Electrical Safety / Sécurité Électrique
• Only connect like circuits: SELV to SELV (ES1 to ES1), TNV-2 to TNV-2 (ES2
to ES2), and Primary to Primary (ES3 to ES3), as defined in IEC 60950-1 and
62368-1.
Ne connectez que les circuits identiques: SELV à SELV (ES1 à ES1), TNV-2 à
TNV-2 (ES2 à ES2) et primaire à primaire (ES3 à ES3), conformément à la
définition des normes CEI 60950-1 et 62368-1.
• The intrabuilding ports of the equipment must use shielded intrabuilding
cabling/wiring that is grounded at both ends.
Les ports de l’équipement se trouvant à l’intérieur d’un bâtiment doivent utiliser
un câblage intérieur blindé mis à la terre aux deux extrémités.