Installation Guide
Table Of Contents
- SAR-Hm and SAR-Hmc Chassis Installation Guide
- Table of Contents
- List of Tables
- List of Figures
- 1 Preface
- 2 Mandatory Regulations
- 2.1 In This Chapter
- 2.2 List of Terms
- 2.3 Safety Warnings / Avertissements de Sécurité
- 2.4 General Requirements
- 2.5 Safety Approvals
- 2.6 Safety Approval for External DC Sources That Power This Equipment
- 2.7 Canada Regulations
- 2.8 United States Regulations
- 2.9 European Union Regulations
- 2.10 United Kingdom Regulations
- 2.11 Australia/New Zealand Regulations
- 2.12 China Regulations
- 2.13 South Korea Regulations
- 2.14 Japan Regulations
- 2.15 Hazardous Locations
- 3 7705 SAR-Hm and 7705 SAR-Hmc Overview
- 3.1 In This Chapter
- 3.2 Overview of the 7705 SAR-Hm and 7705 SAR-Hmc
- 3.2.1 7705 SAR-Hm and 7705 SAR-Hmc Components
- 3.2.1.1 Chassis Features
- 3.2.1.2 Ethernet Ports
- 3.2.1.3 RSVD Port
- 3.2.1.4 RS-232 Ports
- 3.2.1.5 Console Port
- 3.2.1.6 Alarms Port
- 3.2.1.7 Main and Diversity Antenna Connectors
- 3.2.1.8 GPS Antenna Connector
- 3.2.1.9 WLAN Connector
- 3.2.1.10 Chassis Grounding
- 3.2.1.11 Power Supply Input
- 3.2.1.12 High Voltage Power Supply Unit
- 3.2.1.13 Chassis Temperature Control
- 3.2.1.14 Chassis Mounting Options
- 3.2.1 7705 SAR-Hm and 7705 SAR-Hmc Components
- 3.3 Cellular Components
- 3.4 GNSS Components
- 3.5 WLAN Components
- 3.6 Citizens Broadband Radio Service
- 3.7 ADP-Hm Prerequisites and Pre-staging Considerations
- 3.8 Chassis Installation Process
- Customer Document and Product Support
SAR-Hm and SAR-Hmc Chassis Installation Guide Mandatory Regulations
3HE 17810 AAAA TQZZA © 2022 Nokia. Nokia Confidential Information
Use subject to agreed restrictions on disclosure and use.
37
2.6 Safety Approval for External DC Sources That
Power This Equipment
2.6.1 Low-Voltage DC Sources, Nominal 12/24/48 VDC
The low-voltage DC source, from which this equipment derives power, must be
safety approved (as per local requirements) and meet the requirements of a SELV
source as defined in IEC/UL/CSA/EN 60950-1, or an ES2 source as defined in
IEC/UL/CSA/EN 62368-1.
2.6.2 High-Voltage DC Sources, 88 to 300 VDC
The high voltage DC source, from which the HV-PS35 external Power Supply derives
power, must be safety approved (as per local requirements) and meet the
requirements of a Hazardous Voltage Secondary source as defined in
IEC/UL/CSA/EN 60950-1, or an ES3 source as defined in IEC/UL/CSA/EN 62368-1.
The external DC source must have double or reinforced levels of insulation, isolating
the DC output from the AC mains. (AC mains are sources up to and including
300 Vrms, including 230/400 V and 277/480 V sources).
Note: Only the low-voltage DC option is approved for hazardous locations.