Installation Guide
Table Of Contents
- SAR-Hm and SAR-Hmc Chassis Installation Guide
- Table of Contents
- List of Tables
- List of Figures
- 1 Preface
- 2 Mandatory Regulations
- 2.1 In This Chapter
- 2.2 List of Terms
- 2.3 Safety Warnings / Avertissements de Sécurité
- 2.4 General Requirements
- 2.5 Safety Approvals
- 2.6 Safety Approval for External DC Sources That Power This Equipment
- 2.7 Canada Regulations
- 2.8 United States Regulations
- 2.9 European Union Regulations
- 2.10 United Kingdom Regulations
- 2.11 Australia/New Zealand Regulations
- 2.12 China Regulations
- 2.13 South Korea Regulations
- 2.14 Japan Regulations
- 2.15 Hazardous Locations
- 3 7705 SAR-Hm and 7705 SAR-Hmc Overview
- 3.1 In This Chapter
- 3.2 Overview of the 7705 SAR-Hm and 7705 SAR-Hmc
- 3.2.1 7705 SAR-Hm and 7705 SAR-Hmc Components
- 3.2.1.1 Chassis Features
- 3.2.1.2 Ethernet Ports
- 3.2.1.3 RSVD Port
- 3.2.1.4 RS-232 Ports
- 3.2.1.5 Console Port
- 3.2.1.6 Alarms Port
- 3.2.1.7 Main and Diversity Antenna Connectors
- 3.2.1.8 GPS Antenna Connector
- 3.2.1.9 WLAN Connector
- 3.2.1.10 Chassis Grounding
- 3.2.1.11 Power Supply Input
- 3.2.1.12 High Voltage Power Supply Unit
- 3.2.1.13 Chassis Temperature Control
- 3.2.1.14 Chassis Mounting Options
- 3.2.1 7705 SAR-Hm and 7705 SAR-Hmc Components
- 3.3 Cellular Components
- 3.4 GNSS Components
- 3.5 WLAN Components
- 3.6 Citizens Broadband Radio Service
- 3.7 ADP-Hm Prerequisites and Pre-staging Considerations
- 3.8 Chassis Installation Process
- Customer Document and Product Support
SAR-Hm and SAR-Hmc Chassis Installation Guide 7705 SAR-Hm and 7705 SAR-Hmc Overview
3HE 17810 AAAA TQZZA © 2022 Nokia. Nokia Confidential Information
Use subject to agreed restrictions on disclosure and use.
79
3.8 Chassis Installation Process
3.8.1 Preparation
Step 1. Review all regulations. See Mandatory Regulations.
Step 2. Assess and prepare the site and observe all safety warnings. See Site
Preparation.
3.8.2 Pre-staging
This section applies only if you are using ADP-Hm to initialize and commission the
7705 SAR-Hm or 7705 SAR-Hmc in a pre-staging facility.
To pre-stage the 7705 SAR-Hm or 7705 SAR-Hmc chassis, perform the following
steps in order:
Step 1. Unpack the chassis at the pre-staging facility. See Unpacking the Chassis.
Step 2. Install the SIM. See Installing the SIM.
Step 3. Install the chassis on a table top. See Mounting the Chassis on a Flat
Surface.
Step 4. Ground the chassis. See Grounding the Chassis.
Step 5. Connect the antenna and network cables to the chassis. See Making
Indoor Antenna Connections to the 7705 SAR-Hm and Making
Connections to the RJ-45 Ports.
Step 6. Prepare the DC input power cables and connections to the DC power feed.
See Preparing the DC Power Connections. If the HV-PS35 is used, see
High Voltage Power Supply Unit.
Step 7. Power up the system and monitor ADP-Hm. See Powering Up and
Initializing.
Step 8. Shut down all power to the router.
Step 9. Remove the power cables from the router.
Step 10. Remove the antennas and cabling from the router. Do not remove the SIM.
Note: The instructions in this guide assume that the prerequisites for the instantiation of
ADP-Hm have been completed. Refer to the 7705 SAR-Hm and 7705 SAR-Hmc Main
Configuration Guide for more information.