Product Guide
Table Of Contents
- G-2426G-A Product Guide
- Legal notice
- Contents
- About this document
- 1 ETSI ONT safety guidelines
- 2 ETSI environmental and CRoHS guidelines
- 3 ANSI ONT safety guidelines
- 4 G-2426G-A unit data sheet
- 4.1 Overview
- 4.2 G-2426G-A part numbers and identification
- 4.3 G-2426G-A general description
- 4.4 G-2426G-A software and installation feature support
- 4.5 G-2426G-A interfaces and interface capacity
- 4.6 G-2426G-A LEDs
- 4.7 G-2426G-A detailed specifications
- 4.8 G-2426G-A GEM ports and T-CONTs
- 4.9 G-2426G-A performance monitoring statistics
- 4.10 G-2426G-A functional blocks
- 4.11 G-2426G-A standards compliance
- 4.12 G-2426G-A special considerations
- 5 Install a G-2426G-A indoor ONT
- 6 Replace a G-2426G-A indoor ONT
- 7 Configure a G-2426G-A indoor ONT
- 7.1 Overview
- GUI configuration
- Viewing device information and connection status
- Network configuration
- 7.14 Overview
- 7.15 Configuring LAN
- 7.16 Configuring LAN IPv6
- 7.17 Configuring WAN
- 7.18 Configuring WAN DHCP
- 7.19 Configuring Wireless 2.4GHz
- 7.20 Configuring Wireless 5GHz
- 7.21 Configuring wireless scheduling
- 7.22 Configuring IP routing
- 7.23 Configuring DNS
- 7.24 Configuring TR-069
- 7.25 Configuring GRE tunnel
- 7.26 Configuring Upstream (US) Classifier
- 7.27 Configuring QoS
- Security configuration
- Configuring the Application
- Maintenance
- 7.44 Overview
- 7.45 Configuring the password
- 7.46 WAN speed test
- 7.47 Speed test history
- 7.48 Configuring LOID
- 7.49 Configuring SLID
- 7.50 Managing the device
- 7.51 Backing up the configuration
- 7.52 Restoring the configuration
- 7.53 Upgrading firmware
- 7.54 Rebooting the device
- 7.55 Resetting to factory defaults
- 7.56 Diagnosing WAN connections
- 7.57 Viewing log files
- RG Troubleshooting Counters
- 8 ONT configuration file over OMCI
2
Configure the following parameters:
Table 7-22 QoS Config parameters
Field Description
QoS Setting
Type Select a QoS service layer type from the list: L2 or L3.
Classification Criteria
Source MAC Enter the source MAC
Select the Exclude checkbox to exclude the source MAC address.
Interface Select an interface from the list.
Classification Result
DSCP Remark Enter the value for the DSCP mark (range: 0-63); valid only for L3 Criteria.
802.1p Remark Enter the value for the 802.1p (range: 0-7).
Forwarding Policy Enter the number for the forwarding policy (range: 1-7).
Additional fields for L3
Protocol Select a protocol from the list, or select the Exclude checkbox.
Application Select an application from the list.
Source IP and Source IP
Mask
Enter the values for the source IP and IP mask, or select the Exclude checkbox.
Destination IP and
Destination IP Mask
Enter the values for the destination IP and IP mask, or select the Exclude checkbox.
Source Port and Source
Port Max
Enter the values for the source port and port max (highest port number) or select the Exclude checkbox.
Destination Port and
Destination Port Max
Enter the values for the destination port and port max (highest port number), or select the Exclude
checkbox.
3
Click Add to add a QoS policy.
END OF STEPS
Configure a G-2426G-A indoor ONT
Network configuration
Configuring QoS
7368 ISAM ONT
Draft Draft
Nokia – Proprietary and Confidential
Use pursuant to applicable agreements
3FE-XXXXX-AAAA-TCZZA
September 2020
122 Issue 1