Product Guide
Table Of Contents
- G-2426G-A Product Guide
- Legal notice
- Contents
- About this document
- 1 ETSI ONT safety guidelines
- 2 ETSI environmental and CRoHS guidelines
- 3 ANSI ONT safety guidelines
- 4 G-2426G-A unit data sheet
- 4.1 Overview
- 4.2 G-2426G-A part numbers and identification
- 4.3 G-2426G-A general description
- 4.4 G-2426G-A software and installation feature support
- 4.5 G-2426G-A interfaces and interface capacity
- 4.6 G-2426G-A LEDs
- 4.7 G-2426G-A detailed specifications
- 4.8 G-2426G-A GEM ports and T-CONTs
- 4.9 G-2426G-A performance monitoring statistics
- 4.10 G-2426G-A functional blocks
- 4.11 G-2426G-A standards compliance
- 4.12 G-2426G-A special considerations
- 5 Install a G-2426G-A indoor ONT
- 6 Replace a G-2426G-A indoor ONT
- 7 Configure a G-2426G-A indoor ONT
- 7.1 Overview
- GUI configuration
- Viewing device information and connection status
- Network configuration
- 7.14 Overview
- 7.15 Configuring LAN
- 7.16 Configuring LAN IPv6
- 7.17 Configuring WAN
- 7.18 Configuring WAN DHCP
- 7.19 Configuring Wireless 2.4GHz
- 7.20 Configuring Wireless 5GHz
- 7.21 Configuring wireless scheduling
- 7.22 Configuring IP routing
- 7.23 Configuring DNS
- 7.24 Configuring TR-069
- 7.25 Configuring GRE tunnel
- 7.26 Configuring Upstream (US) Classifier
- 7.27 Configuring QoS
- Security configuration
- Configuring the Application
- Maintenance
- 7.44 Overview
- 7.45 Configuring the password
- 7.46 WAN speed test
- 7.47 Speed test history
- 7.48 Configuring LOID
- 7.49 Configuring SLID
- 7.50 Managing the device
- 7.51 Backing up the configuration
- 7.52 Restoring the configuration
- 7.53 Upgrading firmware
- 7.54 Rebooting the device
- 7.55 Resetting to factory defaults
- 7.56 Diagnosing WAN connections
- 7.57 Viewing log files
- RG Troubleshooting Counters
- 8 ONT configuration file over OMCI
1
Deactivate the ONT services at the P-OLT.
If you are using the SLID feature, this step is not required. The ONT and the services can
remain in service (IS).
a. Use the RTRV-ONT command to verify the ONT status and th associated services. Record
the serial number or the SLID of the ONT displayed in the command output.
Example:
RTRV-ONT::ONT-1-1-1-1-1;
b. If the ONT is in service, place the ONT in OOS state.
Example:
ED-ONT::ONT-1-1-1-1-1;
2
If used, disable the Wi-Fi service by pressing the WLAN button; see Figure 6-1, “G-2426G-A
indoor ONT connections” (p. 62)
for the location of the WLAN button.
Figure 6-1 G-2426G-A indoor ONT connections
ON/OFF
RESET
WLAN
POWER
LAN4LAN3LAN2LAN1TEL2TEL1
USB
LEDWPS
36176
POTS port
(RJ-11)
Ethernet ports (4)
(RJ-45)
Power
Reset
button
Wi-Fi
security/
on/off buttons
On/off
button
USB
port
Replace a G-2426G-A indoor ONT
Procedure
7368 ISAM ONT
Draft Draft
September 2020
Issue 1 63
Nokia – Proprietary and Confidential
Use pursuant to applicable agreements
3FE-XXXXX-AAAA-TCZZA