User Guide
Mediamaster 120 C Contents Remote control Connecting the Mediamaster 4 5 Front and Rear panel Connecting the Mediamaster Preparing the remote control Common Connections Connecting to the TV with SCART Connecting to the TV without SCART Connecting a Video recorder with SCART Connecting a Video recorder without SCART 5 5 5 6 6 6 7 7 Connecting the Mediamaster & First-time installation 8 About Smart card Connecting a Hi-fi system First-time installation general information 8 8 8 First-time installation
Remote control This section describes how to operate the Mediamaster using the buttons on the remote control. mute Press once to turn the sound off/on (mute/unmute). Press and hold for a few seconds to switch the Mediamaster into standby mode. In addition, press this button to switch the Mediamaster on. ok To confirm a selection. To open Navi Bars cursor up Move up in the menus and change to the next channel in viewing mode.
Connecting the Mediamaster Front and Rear panel antenna cable for connection of the antenna cable to the cable TV antenna socket Slot for a Conax smart card Reset button TV SCART socket * * for connection to the TV SCART DC in for connecting the cable from the external power supply TV/VCR For connecting to the RF socket on the TV, or to a Video recorder Digital audio Digital audio output (TOS-link optical connection) A constant green light indicates that the Mediamaster is switched ON.
Connecting the Mediamaster Common Connections In this section, you will see some of the most common ways to connect your equipment. If you have problems with your connections and need help, contact your retailer or Nokia Support. Connecting to the TV with SCART • Connect an antenna cable from the cable TV antenna socket in the wall to the antenna cable input on the Mediamaster. • Connect an RF cable from the TV/VCR output on the Mediamaster to the antenna input socket on the TV.
Connecting the Mediamaster Connecting a Video recorder with SCART • Connect an antenna cable from the cable TV antenna socket in the wall to the antenna cable input on the Mediamaster. • Connect a SCART cable between the main SCART socket on the TV and the TV SCART socket on the Video. • Connect an RF cable from the TV/VCR output on the Mediamaster to the RF input socket on the video. • Connect an RF cable from the TV/VCR output on the video to the RF input socket on the TV.
Connecting the Mediamaster & First-time installation About Smart card The Mediamaster is equipped with a built-in decoder for the Conax encryption system. Insert a valid smart card fully into the slot on the back of the Mediamaster. The gold chip must face downwards and inwards. Connecting a Hi-fi system It is possible to connect a TOS link cable from the Digital audio output on the Mediamaster to a Hi-fi system that is equipped with the corresponding audio input.
First-time installation Switching on for the first time and start • Plug in your Mediamaster and the "First-time installation" menu is shown. • Press ok to continue. Select the desired menu language using the buttons. This will become the main language for menus, audio and subtitling. The menu to the right will be shown as long as the Mediamaster is searching for TV and radio channels. All channels found will be listed on the screen. NOTE: the search procedure may take a few minutes.
Watching TV & listening to the radio General information You can watch digital TV and listen to digital radio with this Mediamaster. • If no TV channel is automatically shown after you have finished the installation procedure, press any of the number buttons, or step up and down with cursor up/down to select a channel. • If that does not work, open the Navi Bars with any of the ok or navi buttons. • Scroll to the TV channels folder and select a channel. For more information on Navi Bars, see page 14.
Watching TV & listening to the radio Temporary settings By pressing opt, a menu appears that allows you to configure temporary settings for the channel you are currently watching. If you leave the channel and return to it later, your temporary settings will be deleted. Audio language When available, you can select from the different languages being broadcast. Subtitle language When available, you can select from different subtitle languages.
Watching TV & listening to the radio External equipment With the 0 (zero) button, you can toggle between externally connected equipment, e.g., a VCR (the VCR must be switched on.) This function may not be available on all TV and video models. NOTE: This is also only valid when the units are connected via SCART cables, not if they are connected by RF connection. Sorting channels You can select how the channels shall be sorted in the TV and Radio folders.
Watching TV & listening to the radio Teletext Pressing txt will open a teletext page, if teletext is transmitted for that channel. Select teletext pages using the number buttons on the remote control (Fig. 1). You can also quickly move to the different page options shown on any page by pressing cursor left/right. • Press ok on a highlighted page number to go to that page. • By pressing "0" you can alter between the last two pages that you have most recently watched.
Navi Bars Navigating with Navi Bars Navi Bars are used for selecting TV/Radio channels and to enter menus in which you can perform different settings. 1. Display Navi Bars by pressing the navi or ok button; to hide them, press the back button. Navi Bars Bookmark name Bookmark 2. When Navi Bars are displayed, you can move the folders in horizontal and vertical directions with the cursor buttons. The horizontal row contains folders, e.g. TV, Radio and the Settings folder.
Navi Bars The User folder Banner time out When you switch channels, an information banner will be shown for a few seconds. You can select the duration for which the banner will be shown. Volume bar time-out Select the duration for which the volume bar will be visible on the screen. Main subtitle language If you select the "Visible" option for subtitling and more than one language is available, you may select a main language.
Navi Bars The TV folder Time adjustment The time is adjusted by using the time. buttons, ±1/2 an hour at a TV screen format Select your TV screen format. The 4:3 format is standard for most TV screens. Select 16:9 for widescreen TV. Press opt to get a TV programme in the background from which you can instantly watch the result of your choice. Picture format If you do not have a widescreen TV and the transmission is in widescreen, you can select Fullscreen or Letterbox to change the display format.
Navi Bars Edit lists folder The TV folder may contain a lot of channels. By creating your own lists you can make it easier to handle channels. You can create and edit favourite channel lists in these menus. Select list If you have several lists and want to make changes in them, select which list by using the buttons. Create list Create your own lists containing the channels you most frequently watch. Give each list a specific name, e.g., "News" or "Kids".
Navi Bars Delete selected list If you want to completely delete a list, first select the list with the buttons on the line "Select list". Then, move down to "Delete selected list" and press ok. Rename selected list Give the list a new name. Refer to "Create list" on the previous page. Add/Delete channels From this menu, you add and remove the channels in your lists. A channel is added or removed from the list by pressing info.
Navi Bars Search folder When you want to search for channels at a later time. A channel search procedure can be performed in different ways: Automatic, Manual or Advanced manual search. Automatic search Highlight the line and press ok to start searching for channels Manual search Frequency: Enter the frequency with the numeric buttons on the remote control. Network search: Select "Yes" if you want to search on all of the transmitters connected to a specific network. Symbol rate: Enter the symbol rate.
Navi Bars Access folder Receiver lock To open this menu, you will be asked to enter your access code. The access code is set to 1234 at the factory. If you select "Yes", you will have to enter the access code every time you start the Mediamaster from standby. Age rating control If you want everybody to have access to all available types of programmes, select "No". If you select "Yes", you may block programmes unsuitable for children.
Navi Bars This will appear as a message on your TV screen asking you to press ok to start the download. You are strongly advised to accept the download as this might enable you to receive new features and/or services that may be available to you. You can choose to postpone the download for a more convenient time by pressing the back button. The message will appear again provided that the software is still being broadcast.
Technical specifications Transmission standards DVB-C DIGITAL AUDIO (S/PDIF) Connector 1 x RCA Tuner input & Demodulator Input connector 1 x IEC 169-2 (female) AUDIO RF input frequency 110-872 MHz Optical TOS-link connector Input impedance 75 Ohm Bypass frequency 47-862 MHz Output 0.
Nokia Mediamaster software end-user license IMPORTANT: READ CAREFULLY BEFORE OR USING THE SOFTWARE, NOKIA CORPORATION MULTIMEDIA END-USER SOFTWARE AGREEMENT This Software Agreement ("Agreement") is between You (either an individual or an entity), the End User, and Nokia Corporation Multimedia ("Nokia"). The Agreement authorizes You to use the Software specified in Clause 1 below and which is included in this Nokia digital TV receiver.
Nokia is a registered trademark of Nokia Corporation www.nokia.com 00033264.
