User Guide

For your safety
Read these simple guidelines. Not following them may
be dangerous or against local laws and regulations.
For further information, read the complete user guide.
Keys and parts
1Call key
2. Shortcut key
3. Left selection key
4. Center key
5. Earpiece
6. Right selection key
7. Back key
8. Power/ End key
9. Camera
10. Flash
11. Microphone
12. Back cover opening slot
13. Headset connector
14. Volume keys
15. SOS call key
16. USB connector
To lock the keys, press and hold the * key, or close the
fold.
To unlock the keys, select Unlock.
Do not connect to products that create an output signal,
as this may damage the device. Do not connect any
voltage source to the audio connector. If you connect an
external device or headset, other than those approved
for use with this device, to the audio connector, pay
special attention to volume levels.
Parts of the device are magnetic. Metallic materials may
be attracted to the device. Do not place credit cards or
other magnetic stripe cards near the device for extended
periods of time, since the cards may be damaged.
Some of the accessories mentioned in this user guide,
such as charger, headset, or data cable, may be sold
separately.
Note: You can set the phone to ask for a security code.
Press the scroll key and select Settings. Scroll right
to Privacy & Security, and select Screen Lock >
Screen lock > On, and create a four-digit code. Note,
however, that when you change the code, you need
to remember the new code, as HMD Global is not able
to open or bypass it.
Insert the SIM and memory card
Use only original nano-SIM cards. Use of incompatible SIM
cards may damage the card or the device, and may
corrupt data stored on the card.
Use only compatible memory cards approved for use with
this device. Incompatible cards may damage the card and
the device and corrupt data stored on the card.
Note: Switch the device off and disconnect the charger
and any other device before removing any covers. Avoid
touching electronic components while changing any
covers. Always store and use the device with any covers
attached.
1. Put your fingernail in the small slot at the bottom of
the phone, lift and remove the cover.
2. If the battery is in the phone, to remove it, lift it out.
3. Slide the SIM card holder to the left and open it up.
Place the nano-SIM in the slot face down, close down
the holder and slide it to the right to lock it in place.
SWITCH OFF IN RESTRICTED AREAS
Switch the device off when mobile phone use is not allowed
or when it may cause interference or danger, for example,
in aircraft, in hospitals or near medical equipment, fuel,
chemicals, or blasting areas. Obey all instructions in
restricted areas.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate
the vehicle when driving. Your first consideration while
driving should be road safety.
INTERFERENCE
All wireless devices may be susceptible to interference,
which could affect performance.
AUTHORIZED SERVICE
Only authorized personnel may install or repair this product.
BATTERIES, CHARGERS AND OTHER ACCESSORIES
Use only batteries, chargers, and other accessories
approved by HMD Global for use with this device. Do not
connect incompatible products.
KEEP YOUR DEVICE DRY
Your device is not water-resistant. Keep it dry.
PROTECT YOUR HEARING
To prevent possible hearing damage, do not listen at high
volume levels for long periods. Exercise caution when
holding your device near your ear while the loudspeaker
is in use.
SAR
This device meets RF exposure guidelines when used either
in the normal use position against the ear or when
positioned at least 5 mm (0.2 inches) away from the body.
The specific maximum SAR values can be found in the
Certification Information (SAR) section of this user guide.
For more info, go to www.sar-tick.com.
When a carry case, belt clip or other form of device holder
is used for body-worn operation, it should not contain metal
and should provide at least the above-stated separation
distance from the body. Note that mobile devices may be
transmitting even if you are not making a voice call.
SAFETY AND TEXTING WHILE DRIVING
Safety should be every driver’s first priority. Drivers must
obey all local laws that may include restrictions on the use
of mobile phones or accessories while driving. If use is legal,
always keep your hands free to operate the vehicle while
driving and use a handsfree device whenever possible.
Suspend calls in heavy traffic or hazardous weather. Get to
know your mobile phone and its features and make any
necessary information inputs prior to driving. Do not input
data or engage in text messaging while driving. Mobile
phones should not be used when use may be a distraction
to the driver.
1
2
3
4
16
15
14
8
6
7
5
13
910
11
12
SIM
4. Slide the memory card holder to the left and open it
up. Place the memory card in the slot face down,
close down the holder and slide it to the right to lock
it in place.
5.Put back the battery.
6.Put back the cover.
Important: Do not remove the memory card when an
app is using it. Doing so may damage the memory card
and the device and corrupt data stored on the card.
Switch your phone on or off
Press and hold the power key.
Charge the battery
1.Plug the charger into the wall outlet.
2.Connect the charger to the phone. When done, unplug
the charger from the phone then from the wall outlet.
If the battery is completely discharged, it may take several
minutes before the charging indicator is displayed.
Make a call
1.Type in the phone number.
To type in the + character used for international calls,
press * twice.
2.Press . If asked, select which SIM to use.
3.To end the call, press .
Answer a call
Press .
Send messages
1.Press the scroll key, and select Messages > New.
2. In the To field, press # until you are able to enter
numbers and then type in a phone number, or select
Contacts to add a contact from your contacts list.
3. Write your message. If you need to remove a character,
press the back key.
4.Select SEND.
Add your ICE details
To be able to make SOS calls, you need to add your ICE
(In Case of Emergency) details.
To add your personal details, press the scroll key,
and select Settings > Device > ICE information.
To define the contacts to whom the SOS call is made,
press the scroll key, and select Settings > Device >
ICE information > Options > Create ICE contacts.
Note that you cannot use official emergency call numbers
as your ICE contacts.
Make an SOS call
Once you have the accessibility mode switched on and
added an ICE contact, you can make SOS calls.
To make the call, press and hold the SOS call key for three
seconds, or press the SOS call key quickly twice.
The phone calls your first ICE contact. If the contact
doesn’t answer in 25 seconds, the phone calls the next
contact, and keeps calling your contacts 10 times until
one of them answers the call, or you press .
Note: When the SOS call is answered, the phone goes
to handsfree mode. Do not hold the phone close to your
ear, as the volume may be very loud.
Tip: If you want to keep the accessibility mode on, but
don’t want to make SOS calls, press the scroll key,
and select Settings > Device > Accessibility Mode >
SOS Call > Off.
Camera
1.To switch the camera on, press the scroll key, and
select Camera.
2.To take a photo, press the scroll key.
Keep a safe distance when using the flash. Do not use the
flash on people or animals at close range. Do not cover
the flash while taking a photo.
Find your model number and serial
number (IMEI)
If you need to contact your care point or your service
provider, you may need info such as the model number
and the serial number (IMEI). To see the model number,
dial *#0000#. To see the serial number, dial *#06#.
If you have a dual SIM phone, only IMEI1 is needed.
You can also find the info on your phone label, which is
located under the battery.
The IMEI is also visible on the original sales box.
Product and safety info
For info on HMD Global Privacy Policy, go to www.nokia.com/phones/
privacy. For the online user guide, even more info, and
troubleshooting help, go to www.nokia.com/mobile-support.
Note: Pre-installed system software and apps use a significant
part of memory space.
Network services and costs
You can use your device on the GSM 850, 900,1800, 1900;
WCDMA 2, 4, 5; LTE 2, 4, 5, 7, 12, 13, 17, 25, 26, 41, 66, 71 networks.
You need a subscription with a service provider.
Using some features and services, or downloading content, including
free items, require a network connection. This may cause the
transfer of large amounts of data, which may result in data costs.
You may also need to subscribe to some features.
Emergency calls
Important: Connections in all conditions cannot be guaranteed.
Never rely solely on any wireless phone for essential communications
like medical emergencies.
Before making the call:
• Switch the phone on.
• If the phone keys are locked, unlock them.
• Move to a place with adequate signal strength.
1. Press the end key repeatedly, until the home screen is shown.
2. Type in the official emergency number for your present location.
Emergency call numbers vary by location.
3. Press the call key.
4. Give the necessary info as accurately as possible. Do not end the
call until given permission to do so.
You may also need to do the following:
• If your phone asks for a PIN code, type in the official emergency
number for your present location, and press the call key.
• Switch the call restrictions off in your phone, such as call barring,
fixed dialling, or closed user group.
Take care of your device
Handle your device, battery, charger and accessories with care.
The following suggestions help you keep your device operational.
• Keep the device dry. Precipitation, humidity, and all types of
liquids or moisture can contain minerals that corrode electronic
circuits. If your device gets wet, remove the battery, and let the
device dry.
• Do not use or store the device in dusty or dirty areas.
• Do not store the device in high temperatures. High temperatures
may damage the device or battery.
• Do not store the device in cold temperatures. When the device
warms to its normal temperature, moisture can form inside the
device and damage it.
• Do not open the device other than as instructed in the user guide.
• Unauthorized modifications may damage the device and violate
regulations governing radio devices.
• Do not drop, knock, or shake the device or the battery. Rough
handling can break it.
• Only use a soft, clean, dry cloth to clean the surface of the device.
• Do not paint the device. Paint can prevent proper operation.
• For optimal performance, switch the device off and remove the
battery from time to time.
• Keep the device away from magnets or magnetic fields.
• To keep your important data safe, store it in at least two separate
places, such as your device, memory card, or computer, or write
down important info.
Restore original settings
To reset your phone to its original settings and to remove all your
data, select Settings > Device > Device information > Reset phone.
Recycle
Always return your used electronic products, batteries, and
packaging materials to dedicated collection points. This way you
help prevent uncontrolled waste disposal and promote the recycling
of materials. Electrical and electronic products contain a lot of
valuable materials, including metals (such as copper, aluminum,
steel, and magnesium) and precious metals (such as gold, silver,
and palladium). All materials of the device can be recovered as
materials and energy.
Crossed-out wheelie-bin symbol
The crossed-out wheelie-bin symbol on your product, battery,
literature, or packaging reminds you that all electrical and electronic
products and batteries must be taken to separate collection at the
end of their working life. Do not dispose of these products as
unsorted municipal waste: take them for recycling. For info on your
nearest recycling point, check with your local waste authority.
Battery and charger info
Use your device only with an original HE402 rechargeable battery.
Charge your device with the DSA-5PF18-05 charger. Charger plug
type may vary. HMD Global may make additional battery or charger
models available for this device.
Battery and charger safety
Once charging of your device is complete, unplug the charger from
the device and electrical outlet. Please note that continuous charging
should not exceed 12 hours. If left unused, a fully charged battery will
lose its charge over time.
Always keep the battery between 15°C and 25°C (59°F and 77°F)
for optimal performance. Extreme temperatures reduce the capacity
and lifetime of the battery. A device with a hot or cold battery may
not work temporarily.
Obey local regulations. Recycle when possible. Do not dispose as
household waste.
Do not expose the battery to extremely low air pressure or leave it to
extremely high temperature, for example dispose it in a fire, as that
may cause the battery to explode or leak flammable liquid or gas.
Do not dismantle, cut, crush, bend, puncture, or otherwise damage
the battery in any way. If a battery leaks, do not let liquid touch skin
or eyes. If this happens, immediately flush the affected areas with
water, or seek medical help. Do not modify, attempt to insert foreign
objects into the battery, or immerse or expose it to water or other
liquids. Batteries may explode if damaged.
Use the battery and charger for their intended purposes only.
Improper use, or use of unapproved or incompatible batteries or
chargers may present a risk of fire, explosion, or other hazard,
and may invalidate any approval or warranty. If you believe the
battery or charger is damaged, take it to a service center or your
phone dealer before continuing to use it. Never use a damaged
battery or charger. Only use the charger indoors. Do not charge your
device during a lightning storm.
To unplug a charger or an accessory, hold and pull the plug, not the
cord.
Additionally, the following applies if your device has a removable
battery:
• Always switch the device off and unplug the charger before
removing the battery.
• Accidental short-circuiting can happen when a metallic object
touches the metal strips on the battery. This may damage the
battery or the other object.
Small children
Your device and its accessories are not toys. They may contain small
parts. Keep them out of the reach of small children.
Medical devices
Operation of radio transmitting equipment, including wireless
phones, may interfere with inadequately shielded medical devices'
function. Consult a physician or the medical device's manufacturer to
determine if it is adequately shielded from external radio energy.
Implanted medical devices
To avoid potential interference, manufacturers of implanted medical
devices (such as cardiac pacemakers, insulin pumps, and
neurostimulators) recommend a minimum separation of
15.3 centimeters (6 inches) between a wireless device and the
medical device. Persons who have such devices should:
• Always keep the wireless device more than 15.3 centimeters
(6 inches) from the medical device.
• Not carry the wireless device in a breast pocket.
• Hold the wireless device to the ear opposite the medical device.
• Switch the wireless device off if there is any reason to suspect
that interference is taking place.
• Follow the manufacturer directions for the implanted medical
device.
If you have any questions about using your wireless device with
an implanted medical device, consult your health care provider.
Information on health
The U.S. Food and Drug Administration (FDA) and the U.S. Federal
Communications Commission (FCC) published statements and
questions and answers concerning mobile phones and health.
HMD Global encourages you to visit these websites for updated
information. You can access the FDA website at
www.fda.gov/Radiation-emittingProducts/
RadiationEmittingProductsandProcedures/
HomeBusinessandEntertainment/CellPhones/default.htm and the
FCC website at www.fcc.gov/engineering-technology/
electromagnetic-compatibility-division/radio-frequency-safety/
faq/rf-safety. Additional health-related information is available from
the World Health Organization (WHO) at www.who.int/mediacentre/
factsheets/fs193/en/ and from The National Cancer Institute ("NCI")
at www.cancer.gov/about-cancer/causes-prevention/risk/radiation/
cell-phones-fact-sheet . In the event that you are concerned about
possible health effects, the FDA suggests that you limit your own or
your children’s radio frequency (RF) exposure by limiting the length
of calls or by using handsfree devices.
Hearing
Warning: When you use the headset, your ability to hear outside
sounds may be affected. Do not use the headset where it can
endanger your safety.
Some wireless devices may interfere with some hearing aids.
Nickel
The surface of this device is nickel-free.
Vehicles
Radio signals may affect improperly installed or inadequately
shielded electronic systems in vehicles. For more info, check with the
manufacturer of your vehicle or its equipment.
Only authorized personnel should install the device in a vehicle.
Faulty installation may be dangerous and invalidate your warranty.
Check regularly that all wireless device equipment in your vehicle is
mounted and operating properly. Do not store or carry flammable or
explosive materials in the same compartment as the device, its parts,
or accessories. Do not place your device or accessories in the air bag
deployment area.
Potentially explosive environments
Switch your device off in potentially explosive environments, such as
near gas pumps. Sparks may cause an explosion or fire resulting in
injury or death. Note restrictions in areas with fuel; chemical plants;
or where blasting operations are in progress. Areas with a potentially
explosive environment may not be clearly marked. These usually are
areas where you are advised to switch your engine off, below deck on
boats, chemical transfer or storage facilities, and where the air
contains chemicals or particles. Check with the manufacturers of
vehicles using liquefied petroleum gas (such as propane or butane) if
this device can be safely used in their vicinity.
You can send text messages that are longer than the
character limit for a single message. Longer messages
are sent as two or more messages. Your service provider
may charge accordingly. Characters with accents, other
marks, or some language options, take more space,
and limit the number of characters that can be sent in
a single message.
Use the accessibility mode
With the accessibility mode, the text on the phone display
is bigger and the alerts louder.
To start using the accessibility mode, press the scroll key,
and select Settings > Device > Accessibility Mode > On.
Certification information (SAR)
This mobile device meets guidelines for exposure to radio waves as
set forth by the Federal Communications Commission (FCC). Refer to
the following.
FCC RF Exposure Information
Your handset is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government. The guidelines are based on
standards that were developed by independent scientific
organization through periodic and thorough evaluation of scientific
studies. The standards include a substantial safety margin designed
to assure the safety of all persons, regardless of age and health.
The exposure standard for wireless handsets employs a unit of
measurement known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6 W/kg. The tests are performed
in positions and locations (e.g. at the ear and worn on the body)
as required by the FCC for each model. The highest SAR value for
this handset model as reported to the FCC when tested for use at the
ear is 1.06 W/kg, and when worn on the body in a holder or carry case, is
1.17 W/kg.
Body-worn Operation; This device was tested for typical body-worn
operations with the handset kept 1.5 cm from the body. To
maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 1.5 cm separation distance between the
user's body and the handset. The use of belt clips, holsters and
similar accessories should not contain metallic components in its
assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure requirements,
and should be avoided. The FCC has granted an Equipment
Authorization for this handset model with all reported SAR levels
evaluated as in compliance with the FCC RF emission guidelines. SAR
information on this handset model is on file with the FCC and can be
found under the FCC ID Search section of www.fcc.gov/oet/ea/
after searching on FCC ID 2AJOTTA-1420. Additional information
on Specific Absorption Rates (SAR) can be found on the FCC website
at www.fcc.gov/general/radio-frequency-safety-0.
To send data or messages, a good connection to the network is
needed. Sending may be delayed until such a connection is available.
Follow the separation distance instructions until the sending is
finished.
During general use, the SAR values are usually well below the values
stated above. This is because, for purposes of system efficiency and
to minimise interference on the network, the operating power of your
mobile is automatically decreased when full power is not needed for
the call. The lower the power output, the lower the SAR value.
Device models may have different versions and more than one value.
Component and design changes may occur over time and some
changes could affect SAR values.
For more info, go to www.sar-tick.com. Note that mobile devices
may be transmitting even if you are not making a voice call.
About Digital Rights Management
When using this device, obey all laws and respect local customs,
privacy and legitimate rights of others, including copyrights.
Copyright protection may prevent you from copying, modifying,
or transferring photos, music, and other content.
Copyrights and other notices
FCC notice:
This device complies with part 15 of the FCC rules and standard(s).
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation. For more info, go to www.fcc.gov/engineering-
technology/electromagnetic-compatibility-division/radio-
frequency-safety/faq/rf-safety. Any changes or modifications not
expressly approved by HMD Global could void the user’s authority to
operate this equipment. Note: This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
HAC notice:
Your phone is compliant with the FCC Hearing Aid Compatibility
requirements.
The FCC has adopted HAC rules for digital wireless phones. These
rules require certain phones to be tested and rated under the
American National Standard Institute (ANSI) C63.19-2011 hearing aid
compatibility standards. The ANSI standard for hearing aid
compatibility contains two types of ratings:
• M-Ratings: Rating for less radio frequency interference to enable
acoustic coupling with hearing aids.
• T-Ratings: Rating for inductive coupling with hearing aids in
telecoil mode.
© 2022 HMD Global. HMD Global Oy is the exclusive licensee of the
Nokia brand for phones & tablets. Nokia is a registered trademark of
Nokia Corporation.
The Bluetooth word mark and logos are owned by the Bluetooth SIG,
Inc. and any use of such marks by HMD Global is under license.
This product includes open source software. For applicable copyright
and other notices, permissions, and acknowledgements, select
*#6774# on the home screen.
Manufacturer’s limited warranty
1. General
HMD Global Oy (hereinafter "Manufacturer") provides this
Manufacturer's Limited Warranty ("Warranty") for each genuine
device (the "Product") and related Accessories (as defined in Section
2) included with the Product sales package designated for sale in the
United States of America and Canada.
This Warranty is only applicable in the country where the Product was
purchased through Manufacturer's authorized sales channels,
provided that the Product was intended for sale in that country
("Covered Country"). The warranty services available in a particular
Covered Country may be limited to the Products and country-specific
elements available for sale in that Covered Country.
IF YOU LIVE IN (OR IF A BUSINESS WITH A PRINCIPAL PLACE OF
BUSINESS IN) THE UNITED STATES, SECTION 6 CONTAINS A BINDING
ARBITRATION CLAUSE AND CLASS ACTION WAIVER. IT AFFECTS YOUR
RIGHTS ABOUT HOW TO RESOLVE A DISPUTE WITH MANUFACTURER.
PLEASE READ IT.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR
BY PROVINCE TO PROVINCE OR COUNTRY. ALL PARTS OF THIS
WARRANTY APPLY TO THE MAXIMUM EXTENT PERMITTED BY LAW OR
UNLESS PROHIBITED BY LAW.
The Product and its Accessories must be used in accordance with
the instructions provided in the user guides and leaflets that come
in the Product package and are also available online. From time to
time the Manufacturer may offer additional warranty coverage
that supplements the terms listed here. To learn more about
your Product and any additional coverage, please visit
www.nokia.com/mobile-support.
2. Warranty
The Warranty period starts on the date the Product is sold to an end
user for the first time, as evidenced by the original proof of purchase.
A. The Manufacturer warrants that the Product (including non-user
replaceable batteries) is free from defects in materials and
workmanship ("Defect") for twelve (12) months.
B. The Manufacturer warrants that the Accessories (defined as user-
replaceable batteries, covers, cables, chargers, headsets and any
other accessory included in the sales package) are free from Defect
for six (6) months
During the Warranty period, any Defect covered by this warranty will,
in a reasonable time, be remedied free of charge by either repairing
or replacing the defective Product or Accessory or the defective
part of it at its option, provided that you have returned the
defective Product or Accessory to the original point of purchase
(or Manufacturer or its authorised service centre, as specified
from time to time) before the Warranty period has expired.
When repairing or replacing your Product or Accessory, the
Manufacturer may use new or re-conditioned parts or provide
a refurbished replacement Product or Accessory except where the
use of such re-conditioned parts or refurbished Product or Accessory
is prohibited by local law. In case local law requires the end user to
be informed about the use of re-conditioned parts or refurbished
Products or Accessories, this Warranty document constitutes the
necessary notice in that regard. In case local law requires consent
from the end user for the use of re-conditioned parts or refurbished
Products or Accessories, then such parts or Products or Accessories
will not be used until such consent has been obtained.
When making a Warranty claim, you must provide the legible and
original proof of purchase, clearly indicating the name and the
address of the point of purchase, the place and date of purchase,
the Product type and the serial number together with the
defective Product or Accessory to the original point of purchase
(or Manufacturer or its authorised service centre, as specified
from time to time).
To the fullest extent permitted by applicable law:
(i) No repair or replacement will renew or extend the original Warranty
period unless such renewal or extension is mandated by local law,
in which case the Warranty period is extended by the minimum time
required by law;
(ii) IF YOUR APPLICABLE STATE OR PROVINCIAL LAW GIVES YOU
ANY IMPLIED WARRANTY, INCLUDING AN IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ITS DURATION IS LIMITED TO THE WARRANTY PERIOD. Some States
or Provinces do not allow limitations on how long an implied warranty
lasts, so this limitation may not apply to You; and
(iii) Where the Product, Accessory or parts of a Product or Accessory
have been replaced, the original Product, parts, or Accessories shall
become the Manufacturer's or retailer's property.
Please always back up and remove all personal data, programs,
applications, and content stored on your Product before taking
your Product in for service since repair activities will erase all data
from your Product. If your product is replaced, the data, programs,
applications, and content stored on your Product will not be
transferred to the replacement Product Remove any confidential
information prior to submitting your Product for service.
Manufacturer, its authorised service centres and retailers are not
responsible for the loss the of your data, programs, applications,
or content.
3. What this Warranty does not cover
This Warranty excludes all of the following:
(i) Errors or damages caused by:
(a) exposure to liquid or dampness (unless the Product is declared to
be water-resistant under certain conditions as specified by the
Manufacturer), damage caused by exposure to extreme
electromagnetic field (such as damages caused by microwave oven),
or extreme thermal or environmental conditions or to rapid changes
in such conditions, corrosion, oxidation, spillage of food or liquid, or
influence from chemical products;
(b) physical damage, cracks, dents or scratches caused by a drop or
by external forces impacting the Product or any part of the Product
including but not limited to the cover, display, camera lenses and
buttons (unless specified otherwise by the Manufacturer under
certain conditions);
(c) using your Product with, or connecting it to, any product,
accessory, software, or service not manufactured, authorised, or
supplied by Manufacturer; or chargers, power adaptors or data
cables which do not meet the required technical and safety
specifications described in the user guide;
(d) any third party products sold in combination with your Product;
(e) damage or errors caused by hacking, cracking, viruses, or other
malware, or by unauthorised access to services, accounts, computer
systems, or networks;
(f) power outages or surges capable of affecting the normal use of
the Product; or
(g) other acts beyond the Manufacturer's reasonable control.
(ii) Any wear and tear;
(iii) Use of your Product in a manner that does not comply with its
intended use and the provisions of the user guide;
(iv) If your Product, has been opened, repaired or modified by non-
authorised third parties, or repaired using unauthorised spare parts;
(v) If you have not installed the latest software updates that are
publicly available for your Product within a reasonable time of their
release.
Manufacturer does not warrant that software preinstalled by or on
behalf of Manufacturer in the Product (or subsequent updates and
upgrades) (together "Manufacturer Software") will meet your
requirements, work in combination with any hardware or software
not provided by Manufacturer, be uninterrupted or error free or that
errors are correctable or will be corrected. For Manufacturer
Software-related errors, Manufacturer will make available the latest
version of the Manufacturer Software for reinstallation on your
Product or, if that would not be possible, another remedy, which in
Manufacturer's reasonable discretion, satisfactorily addresses the
error. Some Manufacturer Software may be subject to separate
license terms that are available with the software.
This Warranty is not valid outside of the Covered Country or Region
and does not cover: (a) User guides; (b) Any third party software,
settings, content, data, or links installed or downloaded onto your
Product at any time, or Manufacturer and third-party services or
enabling clients even if preinstalled by Manufacturer (please read the
terms and conditions that may accompany the services as those will
define your rights and obligations); (c) Reduced charging capacity of
the battery resulting from its natural end of Product life, or pixel
defects in your Product's display that are within the scope of industry
standards; (d) SIM card and/or any cellular or other networks or
system on which your Product operates, and (e) A Product where the
serial number, the mobile accessory date code, or the IMEI number
has been removed, erased, defaced, altered or if these are illegible in
any way.
You cannot enforce this Warranty if you refuse to return the Product
or Accessory to the original point of purchase or Manufacturer for
investigation
If this Warranty does not cover your Product or Accessory based on
the above, the retailer, Manufacturer or its authorised service centre
reserves the right to charge for the repair or replacement of your
Product or Accessory following your consent, as well charging a
handling fee.
4. Limitation of Manufacturer’s liability
TO THE EXTENT PERMITTED BY APPLICABLE LAW(S), MANUFACTURER
SHALL NOT UNDER ANY CIRCUMSTANCES BE LIABLE, EITHER
EXPRESSLY OR IMPLIEDLY, FOR ANY
(i) DAMAGES OR LOSSES OF ANY KIND WHATSOEVER RESULTING
FROM OR RELATING TO LOSS OF, DAMAGE TO, OR CORRUPTION OF,
CONTENT OR DATA OR THE RECREATION OR TRANSFER THEREOF
EVEN IF SUCH LOSS, DAMAGE, OR CORRUPTION WAS A RESULT
OF A DEFECT IN YOUR PRODUCT OR ACCESSORY; AND/OR
(ii) LOSS OF PROFIT, USE, PRODUCTIVITY, BUSINESS, CONTRACTS,
REVENUES OR ANTICIPATED SAVINGS, INCREASED COSTS OR
EXPENSES, OR FOR ANY INDIRECT, CONSEQUENTIAL OR SPECIAL
LOSS OR DAMAGE.
To the extent permitted by applicable law, Manufacturer's liability
shall be limited to the purchase value of your Product or Accessory,
as applicable.
5. Choice of law
The laws of the State or Province where you live (or if a business,
or the location of a principal place of business) govern the
interpretation of this Warranty, any claim that Manufacturer has
breached it, and all other claims (including consumer protection,
unfair competition, implied Warranty, and tort claims), regardless
of conflict of law principles, except that the US Federal Arbitration
Act governs arbitration.
6. Binding arbitration and class action waiver if you live
in (or if a business with a principal place of business
located in) the United States
This section applies to any dispute EXCEPT DISPUTES RELATING
TO THE ENFORCEMENT OR VALIDITY OF YOUR, YOUR LICENSOR'S,
MANUFACTURER'S, OR MANUFACTURER'S LICENSOR'S
INTELLECTUAL PROPERTY RIGHTS.
The term "dispute" means any dispute, action or other controversy
between you and Manufacturer concerning the Product, Accessory
(including its price) or this Warranty, whether in contract, warranty,
tort, statute, regulation, ordinance or any other legal or equitable
basis. "Dispute" will be given the broadest possible meaning
allowable under law.
(i) Notice of Dispute. In the event of a dispute, you or Manufacturer
must give the other a Notice of Dispute, which is a written statement
that sets forth the name, address and contact information of the
party giving it, the facts giving rise to the dispute, and the relief
requested. You must send any Notice of Dispute by U.S. Mail to
HMD America, Inc., Attn: Dispute Notice, 1200 Brickell Avenue,
Suite 510, Miami, FL 33131. Manufacturer will send any Notice of
Dispute to you by U.S. Mail to your address if we have it, or otherwise
to your e-mail address. You and Manufacturer will attempt to resolve
any dispute through informal negotiation within 60 days from the
date the Notice of Dispute is sent. After 60 days, you or Manufacturer
may commence arbitration.
(ii) Small Claims Court. You may also litigate any dispute in small
claims court in your county of residence (or if a business, the location
of your principal place of business), if the dispute meets all
requirements to be heard in the small claims court. You may litigate
in small claims court whether or not you negotiated informally first.
(iii) Binding Arbitration. If you and Manufacturer do not resolve any
dispute by informal negotiation or in small claims court, any other
effort to resolve the dispute will be conducted exclusively by
individual binding arbitration governed by the Federal Arbitration Act
("FAA"). Class arbitrations are not permitted. You are giving up the
right to litigate disputes in court before a judge or jury (or participate
as a party or class member). Instead, all disputes will be resolved
before a neutral arbitrator, whose decision will be final except for
a limited right of appeal under the FAA. Any court with jurisdiction
over the parties may enforce the arbitrator's award.
(iv) Class Action Waiver. Any proceedings to resolve or litigate any
dispute in any forum will be conducted solely on an individual basis.
Neither you nor Manufacturer will seek to have any dispute heard
as a class action, private attorney general action, or in any other
proceeding in which either party acts or proposes to act in a
representative capacity. No arbitration or other proceeding will be
combined with another without the prior written consent of all
parties to all affected arbitrations or proceedings.
(v) Arbitration Procedure. Any arbitration will be conducted by the
American Arbitration Association (the "AAA") under its Commercial
Arbitration Rules. If you are an individual and use the Product or
Accessory for personal or household use, or if the value of the
dispute is $75,000 USD or less whether or not you are an individual
or how you use the Product or Accessory, the AAA's Consumer
Arbitration Rules will apply. For more information, see www.adr.org or
call 1-800-778-7879. To commence arbitration, send a request to
HMD America, Inc., Attn: Dispute Notice, 1200 Brickell Avenue,
Suite 510, Miami, FL 33131. You agree to commence arbitration
only in your county of residence (or if a business, the county where
your principal place of business is located). Manufacturer agrees
to commence arbitration only in your county of residence (or if
a business, the county where your principal place of business is
located). You may request a telephonic or in-person hearing by
following the AAA rules. In a dispute involving $10,000 USD or less,
any hearing will be telephonic unless the arbitrator finds good cause
to hold an in-person hearing instead. The arbitrator may award the
same damages to you individually as a court could. The arbitrator
Not all phones have been rated. A phone is considered hearing aid
compatible under FCC rules if it is rated M3 or M4 for acoustic
coupling and T3 or T4 for inductive coupling. These ratings are given
on a scale from one to four, where four is the most compatible.
Your phone meets the M4/T4 level rating.
However, hearing aid compatibility ratings don't guarantee that
interference to your hearing aids won't happen. Results will vary,
depending on the level of immunity of your hearing device and the
degree of your hearing loss. If your hearing device happens to be
vulnerable to interference, you may not be able to use a rated phone
successfully. Trying out the phone with your hearing device is the
best way to evaluate it for your personal needs.
This phone has been tested and rated for use with hearing aids for
some of the wireless technologies that it uses. However, there may
be some newer wireless technologies used in this phone that have
not been tested yet for use with hearing aids. It is important to try the
different features of this phone thoroughly and in different
locations, using your hearing aid or cochlear implant, to determine if
you hear any interfering noise. Consult your service provider or the
manufacturer of this phone for information on hearing aid
compatibility. If you have questions about return or exchange
policies, consult your service provider or phone retailer.
Hearing devices may also be rated. Your hearing device manufacturer
or hearing health professional may help you find this rating. For more
information about FCC Hearing Aid Compatibility, please go to
http://www.fcc.gov/cgb/dro.
Manufacturer and/or importer in EU: HMD Global Oy, Bertel Jungin
aukio 9, 02600 Espoo, Finland.
HMD Global Privacy Policy, available at http://www.nokia.com/
phones/privacy, applies to your use of the device.
may award declaratory or injunctive relief only to you individually,
and only to the extent required to satisfy your individual claim.
(vi) Arbitration Fees and Payments.
(a) Disputes Involving $75,000 USD or Less. Manufacturer will
promptly reimburse your filing fees and pay the AAA's and
arbitrator's fees and expenses. If you reject Manufacturer's last
written settlement offer made before the arbitrator was appointed
("Manufacturer's last written offer"), and your dispute goes all the
way to an arbitrator's decision (called an "award"), and the arbitrator
awards you more than Manufacturer's last written offer,
Manufacturer will:
(i) pay the greater of the award or $1,000 USD;
(ii) pay your reasonable attorney's fees, if any; and
(iii) reimburse any out of pocket expenses (including expert witness
fees and costs) that your attorney reasonably accrues for
investigating, preparing, and pursuing your claim in arbitration.
The arbitrator will determine the amount of fees, costs, and
expenses unless you and Manufacturer agree on them.
(b) Disputes Involving More Than $75,000 USD. The AAA rules will
govern payment of filing fees and the AAA's and arbitrator's fees
and expenses.
(c) Disputes Involving Any Amount. In any arbitration you commence,
Manufacturer will seek its AAA or arbitrator's fees and expenses,
or your filing fees it reimbursed, only if the arbitrator finds the
arbitration frivolous or brought for an improper purpose. In any
arbitration Manufacturer commences, Manufacturer will pay all filing,
AAA, and arbitrator's fees and expenses. Manufacturer will not seek
its attorney's fees or expenses from you in any arbitration. Fees and
expenses are not counted in determining how much a dispute
involves.
(vii) Conflict with AAA Rules. This Warranty governs to the extent it
conflicts with AAA's Commercial Arbitration Rules or Consumer
Arbitration Rules.
(viii) Claims or Disputes Must Be Filed Within One Year. To the extent
permitted by law, any claim or dispute to which Section 6 applies
must be filed within one year in small claims court, an arbitration
proceeding, or in court, if Section 6 permits the dispute to be filed
in court instead of arbitration. The one-year period begins when the
claim or Notice of Dispute first could be filed. If such a claim or
dispute is not filed within one year, it is permanently barred.
(ix) Severability. If the class action waiver in this Section is found to
be illegal or unenforceable as to all or some parts of a dispute, then
Section 6 will not apply to those parts. Instead, those parts will be
severed and proceed in a court of law, with the remaining parts
proceeding in arbitration. If any other provision of Section 6 is found
to be illegal or unenforceable, that provision will be severed with the
remainder of this Section 6 remaining in full force and effect.
7. Other important notices
Manufacturer reserves the right to make changes to the location and
availability of its authorized service centers network at any time.
Your Product may contain specific elements which may not operate
as intended when used outside of the original country of purchase.
Manufacturer's Address:
HMD Global Oy, Bertel Jungin aukio 9, 02600 Espoo, Finland
United States: HMD America, Inc., 1200 Brickell Avenue, Suite
510,Miami, FL 33131.
Canada: HMD America, Inc., 1200 Brickell Avenue, Suite 510,Miami, FL
33131.
TA-1420
EN-US
Quick guide Nokia xx Flip
EN_ES_xxxxxxxx_Nokia_xx_QSG_Issue1_0.book Page 1