Owner’s Manual MEDIAMASTER 9400S
MEDIAMASTER 9400S Contents FOR YOUR SAFETY Rear panel Front panel INSTALLATION OF THE MEDIAMASTER Connecting the Mediamaster to the satellite dish Connecting the Mediamaster to a TV set Connecting to a TV and a video recorder If your VCR does not have a SCARTConnector Connecting to an analogue satellitereceiver and a video recorder Connecting to Hi Fi system Preparing the remote control Before you continue REMOTE CONTROL BASIC SETTINGS Tuning procedure when RF Connections are used The Welcome Menu Language
FOR YOUR SAFETY • • • • • • • • • Keep a clear space around the Mediamaster to allow for sufficient ventilation. Do not cover the Mediamaster or place it on a unit that emits heat. Use a soft cloth and a mild solution of dish washing liquid to clean the casing. Never allow liquids, spray or other materials to come into contact with the inside of the Mediamaster. Service should be carried out only at a Nokia authorized service center. Do not connect or modify cables when the Mediamaster is plugged in.
Front panel Power To turn the receiver on/off (standby). Up/Down Select channel number, up/down. Display Shows channel number, remote control signal and time in standby mode. At start up, it displays the model number.
Connecting the Mediamaster to the satellite dish Installing the satellite dish Ÿ Ÿ Your satellite dish should be installed with a cable for you to connect to the Mediamaster. If you do not have this cable you will need to buy one from a dealer (tell the dealer you need a coaxial cable and F-connectors). Connect the cable from the satellite dish to the socket marked ”LNB IN” on the back of the Mediamaster.
Connecting to a TV and a Video recorder Refer to your video recorder manual for full instructions. Ÿ Connect one SCART cable between the main SCART socket on the TV and the TV SCART socket on the Mediamaster. Ÿ Ÿ Ÿ Connect another SCART cable between the VCR and the AUX SCART socket on the Mediamaster. Connect the RF cable from the RF output on the VCR to the TV aerial input on the TV. Connect the TV aerial to the RF input socket on the VCR.
Connecting to Hi Fi system Connect an RCA/Cinch stereo cable from the AUDIO L R sockets on the Mediamaster to the LINE, AUX, SPARE or EXTRA input sockets on your Hi Fi system. Preparing the remote control Ÿ Remove the cover on the battery compartment at the bottom of the remote control handset. Ÿ Insert the 2 x AAA (1,5 V) batteries, as shown in the diagram, taking care to observe the + and markings indicated inside. Ÿ Replace the cover.
REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control. Some of the functions can also be carried out using the buttons on the front panel. To switch the Mediamaster in and out of standby mode. EXIT TV To return to the viewing mode from a menu without storing settings (in menu mode). To switch between TV or Radio (in viewing mode). To turn the sound off/on (mute). To adjust the volume of digital programmes.
BASIC SETTINGS Once you have correctly connected the Mediamaster, you also have to perform some “Basic Settings”. During this procedure, helpful information is displayed at the bottom of the menus. Please note! The OK button always confirms a selection within these menus, and pressing it will take you to the next step in the installation process. However, and this is important, often more than one value has to be entered in a menu. First, perform all necessary settings on the different lines.
The Welcome Menu To install the Mediamaster properly you have to adjust a few settings. You will always be guided by the information at the bottom of the menus. When you have finished the final part of the setup procedure you can start watching TV channels and listening to radio channels. Now you should have the Welcome Menu on the TV screen. Press the OK button to proceed. Language Settings Select the menu language that you desire. This will define the language shown in the menus.
Satellite name: From here you can select a name for the configuration. Switch Type: There are in principle two kinds of external DiSEqC switches on the market at present. One for connection of two LNBs. The other one for connection of up to 4 LNBs. If you have the other switch, defined as DiSEqC, Level 1 or 2 on the market, select “DiSEqC 1, 2, (3 or 4)”, for each LNB connected to respective inputs on this switch. LNB Type: Selection is possible for different kinds of LNBs.
Manual Channel Search You can use manual channel search if you want to add new channels later. For example If you have a special antenna configuration which is not assigned in the “Antenna alternative” menu, you can add new channels using the “manual channel search” function. When you perform a Manual Search you first need to enter some parameters for the channel search to work.
TV Screen Format If you have a TV set with a 4:3 picture format, and the transmission is in 16:9, you can select “4:3 (Pan & Scan)” or “4:3 (Letterbox)” to change display format. “4:3 (Pan & Scan)” will fill up the screen vertically, but cut off some information from the left and right sides of the picture. “4:3 (Letterbox)” will give a complete picture, but leave black areas at the top and bottom.
TV Guide By pressing the GUIDE button you obtain access to the TV Guide which gives the titles of the current programmes on the different channels. By pressing the LEFT or RIGHT button you also can also obtain information about the next programme. The minimized viewing window also helps you to select channels and information. Use the Up/Down buttons to move the cursor to different programme areas. You can obtain extended information for a programme by pressing the “i” button.
List of Radio Channels While listening to radio Programmes you can see a programme list on the screen by pressing the OK button. You can change to another channel by pressing the UP/DOWN buttons and then pressing the OK button. To move faster (8 at the time) between the channels you can also use the DOUBLE ARROW buttons. Video Recorder With a Video Cassette Recorder (VCR) connected you can watch/record video tapes.
TV Channels and Radio Channels TV/Radio Channels will show a list with the names of the different channels. To move faster within the list, use the DOUBLE ARROW buttons. Press OK to enter a marked channel. TV Guide and Radio Guide These guides will give you an overview of programme information from the TV/Radio channels. Step to different channel numbers with the UP/DOWN buttons. If you stop on a highlighted line and press OK, you will exit the menu and enter the highlighted channel.
Rearrange List If you have created several Favorite lists you can determine the sequence in which the lists will appear. To rearrange channels, select the list which you want to move using the OK button. Move the channels to the desired position using the UP/DOWN button and press OK. Rename List You can change the list name with the virtual keyboard on the screen. Type in the text you want using the remote control arrow keys.
Rearrange Channels You can arrange the order of channels within your favorite lists. To rearrange channels, select the channel which you want to move using the OK button. Move the channels to the desired position using the UP/DOWN button and press OK. Remove Channels From here, when the “All TV” list is selected in the “Edit Channels” menu, you can remove channels. Please note. Channels deleted this way will be permanently removed. The only way to get them back is to perform a new channel search.
Change access code From here you can change the access code from the standard 1234. DO NOT FORGET IT! Without it you do not have access to any of the functions where the code is required! If you forget it, you have to contact an Authorized Nokia Service Center to get help. Language Settings From here you can change the language for the menus, main audio language and alternative audio language. System Settings From here you can adjust settings concerning your TV.
On/Off Timer Setting You can enjoy this On/Off Timer for such a convenience as wake-up or automatic VCR recording. Mediamaster will be automatically switched-on and play specified channel for the specified time, and then switched-off. You may specify up to 8 separate lists with turn-on time, date, duration, channel and occurrence options. Time Setting You can select the operation mode of the On/Off timer by pressing LEFT/RIGHT button on the remote control.
INSTALLATION SUBMENUS Select this Menu from the line “Installation” in the Main Menu. The submenu will give you the opportunity to change the preferences performed during first time installation. You can also add features that were not included in the first installation. Please note that helpful information for every line is given at the end of the menu. Antenna Satellite Configuration Please refer to page 11. Automatic Channel Search Please refer to page 12.
Reinstall This will start the Installation procedure from the “Welcome Menu”. When you press OK in the “Welcome Menu” again, be aware of the fact, that all previous channels and settings will be erased! To exit the ”Reinstall” menu without erasing any channels, press “Back”. System Information This gives general information about which hardware and software version your Mediamaster is running on.
GLOSSARY OF TERMS AGC Acquisition Gain Control. Audio system With digital satellite reception, the sound is transmitted in packages and is elected either in a special audio mode or pre-selected by using the installation set-up. This makes it possible to select between several different languages in a film. The number of choices is dependent on what is available in the signal. DiSEqC Digital satellite Equipment Control.
PROBLEM SOLVING Problem Possible causes What to do The display on the front panel does not light up/is not lit. No sound or picture. Mains lead is not connected. Check that the mains lead is plugged into the power socket. Bad picture/blocking error. The satellite dish is not pointing at the satellite. Adjust the dish. Check the signal level indicator in one of the channel search submenus. No signal or weak signal.
TECHNICAL SPECIFICATION Transmission Standards DVB,MPEG2 TV SCART RGB, CVBS, Audio LNB/Tuner input Connector AUX SCART CVBS, Audio Input frequency Max Current Supply Voltage DiSEqC RF Impedance Demodulator QPSK Symbol rate SCPC and MCPC 2 x F-type (Loop Through) 950-2150MHz 500mA max 13V/18V 1.
MENUS SCREEN STRUCTURE First Time Installation Welcome Menu Language Settings 1.Menu Language 2.Main Audio Lang… 3.Alternative… 4…… Main Menu 1.TV Channels 2.Radio Channels 3.TV Guide 4.Radio Guide 5.Edit Channels 6.User Preferences 7.Game 8.Installation 5.Edit Channels 1.Rearrage List 2.Rename List 3.Add Channels 4.Lock Channels 5.Rearrange Channels 6.Remove Channel On/Off Timer Setting 1.Timer Defined 2.Timer Defined 3…. … 8.
Nokia is a registered trademark of Nokia Corporation www.nokia.