Nokia Bluetooth Headset BH-219 Issue 2.0 © 2010 Nokia. All rights reserved.
© 2010 Nokia. All rights reserved.
© 2010 Nokia. All rights reserved.
DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION declares that this BH-219 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/ phones/declaration_of_conformity/. © 2010 Nokia. All rights reserved. Nokia, Nokia Connecting People and the Nokia Original Accessories logo are trademarks or registered trademarks of Nokia Corporation.
your Nokia dealer. This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited. Introduction With the Nokia Bluetooth Headset BH-219, you can make and answer calls hands-free with your compatible mobile device. Read this user guide carefully before using the headset. Also, read the user guide for the device that you connect to the headset. The surface of this device is nickelfree.
Get started The headset contains the following parts shown on the title page: multifunction key (1), Near Field Communication (NFC) area (2), charger connector (3), microphone (4), earloop (5), earpiece (6), and indicator light (7). Before using the headset, you must charge the battery and pair the headset with a compatible device. Parts of the device are magnetic. Metallic materials may be attracted to the device.
The fully charged battery has power for up to 6 hours of talk time or up to 100 hours of standby time. To check the battery charge when the headset is not connected to a charger, press the multifunction key when the headset is connected to a mobile device. If the indicator light is green, the charge level is sufficient. If the light is yellow, you may need to recharge the battery soon. If the light is red, recharge the battery.
1. Make sure your mobile device is switched on and the headset is off. Pair and connect the headset 2. If the headset has not been previously paired with a device, Before using the headset, you switch on the headset. The must pair and connect it to a headset enters pairing mode, compatible device. and the blue indicator light You can pair the headset with up starts to flash quickly.
4. Select the headset from the list of found devices. 5. If necessary, enter the passcode 0000 to pair and connect the headset to your device. In some devices, you may need to make the connection separately after pairing. When the headset is connected to at least one device and is ready for use, the blue indicator light flashes slowly.
and push the new earpad into place (9). Place the headset on the ear To use the headset with the earloop, attach the earloop to it (11). To detach the earloop, gently pull it from the headset. You can rotate the earpad to keep the headset securely in the ear (10). For example, if you use the headset on the right ear, you may need to rotate the earpad to the right for the best fit. If you wear an earring, make sure it is not accidentally attached to the earpad.
no call is in progress, press and hold the multifunction key for about 2 seconds. Proceed as described in the user guide of the mobile device. To answer or end a call, press the multifunction key (14). To reject a call, press the multifunction key twice. To switch a call between the headset and a compatible connected device, press and hold the multifunction key for about 2 seconds. Connect to two devices The headset can be connected to two devices at the same time.
To end the active call on one connected device and make the call on hold active on the other device, press the multifunction key. To switch between the active call on one device and the call on hold on the other device, press and hold the multifunction key for about 2 seconds. Clear pairings To clear the pairings from the headset, switch off the headset, and press and hold the multifunction key for about 8 seconds.
discharged hundreds of times, but it will eventually wear out. Talk and standby times are estimates only. Actual times are affected by, for example, device settings, features being used, battery condition, and temperature. If the battery has not been used for a long time, to begin charging, you may need to connect the charger, then disconnect and reconnect it. If the battery is completely discharged, it may take several minutes before the charging indicator is displayed.
Take care of your device Handle your device, charger and accessories with care. The following suggestions help you protect your warranty coverage. • Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode electronic circuits. If your device gets wet, allow it to dry completely. • Do not use or store the device in dusty or dirty areas. Moving parts and electronic components can be damaged. • Do not store the device in high temperatures.
information and how to recycle your Nokia products at www.nokia.com/ werecycle, or with a mobile device, www.nokia.mobi/werecycle. The crossed-out wheeledbin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European Union. Do not dispose of these products as unsorted municipal waste.