ENGINEERING w w w.noktaengineering.
INTRODUCTION Thank you for choosing and purchasing our Nokta Velox One detector. Manufacturing high-tech metal detectors since 2001, Nokta Engineering has played a key role in the development of this sector. Nokta Engineering is particularly known for its technological know-how and professional staff. Seeking to create different kind of technology, Nokta Engineering offers both high-quality products and services to its consumers all around the world.
INTRODUCTION WARNINGS : .................................................................................................................................................................................... ASSEMBLY : .................................................................................................................................................................................... 3-4 5-8 CORRECT WAY OF HOLDING 9 : ........................................................................
WARNINGS WARNINGS! LEGAL WARNINGS ► When using the device, comply with all applicable laws and regulations. Do not use the device in private premises, historic sites and military zones. Notify the authorities of any historical or cultural findings. WARNINGS ABOUT THE DEVICE ► This is a high-tech electronic device. Do not assemble or use the device before reading the user manual. ► Do not expose the device or the search coil to very hot or cold conditions for extended periods of time.
IMPORTANT Do not use the device indoors. The device will constantly give target signals inside places like homes where there are many metals present. Use the device outdoors, in open fields. IMPORTANT WARNINGS Do not carry any metal objects while using the device. Keep the device away from your shoes while walking. The device may detect the metals on you or inside your shoes as targets. Do not let another detector or an electromagnetic device come in close proximity (10m (33ft.)) to the device.
ASSEMBLY 1 3 2 4 5 6 7 8 5 10 9 NOKTA ENGINEERING 11 1) System Box 2) Handle and S-Rod 3) Search Coil 4) Search Coil Cover 5) Upper Shaft 6) Extension Shaft 7) Wingnut, Fastening Screw and Washers 8) 8 AA Batteries 9) Battery Case 10) Battery Case Cover 11) Headphones Coil cover use is optional. It protects the search coil from scratches. If you want to use the cover, attach the cover to the coil and press firmly on the edges to secure.
ASSEMBLY Holding the metal pin pressed, insert the S-rod into its place underneath the system box and secure it by tightening the wingnut as shown in the picture. Again by holding the metal pin pressed, insert the upper shaft into the S-rod and click the pin into its hole. Then, secure it by tightening the twist lock. Insert the extension shaft into the upper shaft holding the metal pin pressed and adjust the height by clicking the pin into one of the holes.
ASSEMBLY Place the washers into the openings on both sides at the end of the extension shaft. After placing the shaft on the coil as shown in the picture, insert the fastening screw through the hole and tighten it using the wingnut. 7 NOKTA ENGINEERING Wrap the coil cable around the shaft all the way up as shown in the picture and after inserting it in the coil input socket underneath the system box, secure it by twisting the connector. Pay attention to not wrap the cable too tight during this step.
ASSEMBLY 1 3b 2 4 3a 5 To attach the battery case to the system box: Follow the above steps in the pictures. After step 5, plug the battery case cable into the socket underneath the system box and tighten securely. Assembly is completed.
CORRECT WAY OF HOLDING 9 Shaft height is wrong. Shaft height is correct. It is very important to adjust the shaft to your height correctly to be able to search without discomfort and fatigue. Adjust the height of the shaft so that you are standing in an upright position, your arm is relaxed and the search coil is approximately 5cm (~2'') above the ground.
CORRECT WAY OF SWEEPING Wrong search coil angle Wrong search coil angle Correct search coil angle Incorrect way of sweeping Correct way of sweeping It is important to keep the search coil parallel to the ground in order to get accurate results. The search coil must be parallel to the ground at all times.
BATTERY The device comes with 8 AA Alkaline batteries and a battery case. Insert the batteries in the case paying attention to the + (plus) and – (minus) poles. When batteries are full, they will provide approximately 25-30 hours of use. Different types or brand of batteries may have different lifetimes. LOW BATTERY: When the batteries are low, the device will produce a warning sound approximately once every minute. The device will shut down automatically 3-4 hours after the warning.
DEVICE INTRODUCTION SENSITIVITY IRON DISC.
CONTROLS TURNING ON THE DEVICE Mineral 3 Off Mineral 2 On Mineral 1 To turn on the device, rotate the On/Off knob to ON. Turn the same knob to OFF position when you want to turn off the device. When the device is turned on, a melody will be heard and approximately 10 seconds later you will hear a long beep indicating that the device is ready to use. The device will provide more depth at on position.
CONTROLS For maximum depth, do not turn the ground balance knob to the right more than necessary. Generally speaking, the mid-level (between 4-7) offers the most ideal and stable detection capability on different types of ground without sacrificing depth. GROUND BALANCE As the ground balance goes into the right area, the device will start losing depth for some non-ferrous metals except for gold.
CONTROLS IRON DISCRIMINATION IRON DISC. This setting is designed for tough ground conditions and experienced users. For normal ground conditions or if you do not want to bother with this setting it is recommended that you keep it at the factory setting (FS). This setting has 2 main purposes: 1) Especially in areas of high iron mineralization and wet beach sand you may not be able to ground balance the device. In such a case, you can use iron discrimination.
CONTROLS MINERAL MODES Mineral 3 Off Mineral 2 On Mineral 1 Mineral Modes: If you are searching on high mineralized ground (extremely salty soil, wet beach sand, wet plowed land or highly magnetic ground conditions) you may not be able to ground balance the device. In such a case, first turn the On/Off knob to mineral 1. If the device is still getting noise, turn it to mineral 2 or mineral 3. This will eliminate the noise and false signals caused by mineralization.
SEARCHING AND METAL DETECTION SEARCHING AND METAL DETECTION After the settings are adjusted, you can start searching by lifting the search coil 5cm. above the ground and sweeping it right and left, keeping it parallel to the ground. 5cm The device operates on the principle of motion. This means that you must move the search coil over the target or the target over the search coil, in order for the device to see it. In other words, metal detection is not possible without moving the search coil.
TECHNICAL SPECIFICATIONS Operating Principle: Operating Frequency: Metal Identification: Induction Balance 17.5 KHz Audio warning Audio Discrimination: 3 tones Sensitivity Setting: Manual Ground Balance: Manual Search Coil: Battery: Headphone Output: 28cm (11'') waterproof Double-D 8 x AA Alkaline Batteries 1/4'' mono Length: 125-145cm (49''-57'') extendable Weight: 2.0kg (4.
Emek Mah. Sivatyolu Cad. Sakiz Sok. No: 4 34785 Sancaktepe - Istanbul / Turkey Phone : +90 216 415 56 86 Fax : +90 216 415 63 43 E-mail: info@noktaengineering.
