User Manual

devices.
(e) Select “BTHS” from the list.
(f) Enter the pre-programmed passkey “0000” and press “OK”
to pair the headset and the handset. When pairing is
completed, you may hear two beeps and the LED will flash
blue and amber alternatively every 2.5 seconds. Now the
headset is in standby mode.
(g) Return and to go back to your handset’s main menu.
(Most mobile handset models, will display a headset icon.)
You should now be able to make/receive calls through the
headset. Please place the mobile handset at a distance of
up to 10 meters from the headset. (Any obstacle may result
in a shorter sensing distance.)
IMPORTANT: Under pairing mode, if pairing procedures are
not completed within 2 minutes, the headset will be in standby
mode and will emit a beep. Please repeat steps (b) to (g) to
re-pair the headset and mobile handset.
Connection/Link to a Mobile Handset
When pairing is completed, the headset is in standby mode.
Before you place or answer a call, if the headset ICON is not
displayed on the handset screen, please follow the simple steps
to activate the Bluetooth connection/link through your handset or
headset until the headset ICON is on the screen.
(a) On Handset: Select “BTHS” from the list of paired devices
on your handset screen.
(b) On Headset: Short press the headset MFB and select
“Accept” on the handset screen to accept the connection.
IMPORTANT: Whenever the Bluetooth connection/link is
removed and you cannot see the headset ICON on your mobile
phone’s screen, please follow the activate connection/link steps.
Disconnection to the Mobile Handset
You may connect your headset with another Bluetooth mobile
handset. Please follow the simple steps to disconnect your
Bluetooth headset with the pre-paired handset.
(a) Power off the headset.
(b) Select “Disconnect” to remove the previous connection
from your handset list.
USING THE HEADSET
Once the pairing is completed and the battery is fully charged,
you may access the following functions. Some of the functions
listed below are only accessible on handsets supporting a
Hands-Free Profile.
(a) Answering a Call: To answer a call, wait for the ringing
tone from the headset, then short press the MFB on your
Bluetooth headset to accept the call, or answer the call via your
mobile handset in the normal way.
(b) Ending a Call: Short press the MFB, to end your call or
end the call via your mobile handset in the normal way. You will
hear a beep from the headset when your call is completed.
(c) Reject a Call: When you hear the ringing tone, press and
hold the MFB on your Bluetooth headset for 3 seconds until you
hear a beep.
(d) Voice Dialing: If your mobile handset is voice dialing
enabled, in standby mode, press the MFB and when you hear a
beep, say the voice tag.
IMPORTANT: Please make sure to record voice tag into the mobile
handset before you use the voice dialing function. This function is
only supported by mobile handsets with a Bluetooth Hands-Free
Profile. You may not hear the beep, using certain mobile phone
models. Please refer to your mobile handset user guide for
additional information.
(e) Last Number Re-Dial: In standby mode, short press the
MFB button twice to redial the last number.
(f) Adjusting the Volume: During conversation, press the volume
buttons repeatedly until you reach the desired volume level.
(g) Mute & Un-mute:
1. Mute the headset: Press the V+ button for 3 seconds.
The LED will flash blue.
2. Un-mute the headset: Press and hold V+ and V- buttons
simultaneously.
(h) Call Inter-Changing:
1. Headset to Handset: During conversation, press V-
button for 3 seconds.
2. Handset to Headset: Press the V- button for 3 seconds
or MFB button, depending on the features available on your
phone model.
VISUAL INDICATORS
Headset Mode Amber LED Blue LED Sound
Off Mode
Off Of
f
Power On
On for 1 sec. 2 beeps
Power Off
On for 1 sec. 2 beeps
Standby - before
Pairing
Flashes 2 times
every 2.5 sec.
Standby - after
Pairing
Flashes once
every 2.5 sec.
Standby - Low
Voltage
f
lashes
2 beeps
every 30
sec.
Talking in Progress
Flashes 3 times
every 2.5 sec.
Pairing in Progress
Flashes alternatively
Pairing Completed
Flashes once
every 2.5 sec.
2 beeps
Mute
Flashes 3 times
every 2.5 sec.
1 beep
Un-Mute
Flashes 3 times
every 2.5 sec.
1 beep
Charging in
Progress
Steady
Charging
Completed
Off Of
f
Trouble Shooting:
Please note that you should also be familiar with the operation of
your mobile phone and how to connect to Bluetooth devices.
Please read your mobile phone user guide carefully. Please note
that the Bluetooth headset will only work with Bluetooth mobile
phones. For operation with a PC or laptop device please note that
these devices should also be Bluetooth enabled with appropriate
third party software in order to enable correct operation.
Symptom/Problem Solution
When Talk button is
pressed, no LED
indicator
• Unit not charged
• Consult authorized dealer
Headset powers on
with blue LED flashing
but no connection to
mobile phone
• Check unit is paired to phone.
Check settings in phone.
Headset default name is BTHS
• Check phone is switched on
• Check handsfree settings for
phone
• Ensure headset & phone are
within Maximum 10M range
Headset does not
charge
• Check mains charger adapter is
connected to the headset
securely & is switched on
• Check mains charger is working
using another device
• Consult authorized dealer
CUSTOMER SERVICE INFORMATION
For other Nolan Bluetooth products or support, please view our
website – www.nolan-sys.com or email [e-mail] or
contact your local representative.
DISCLAIMER
Whilst every effort has been made to ensure that the information in
this manual is accurate and complete, no liability will be accepted
for any errors and/or omissions made. The manufacturer reserves
the right to make changes and improvements to the specifications
and features of the hardware and firmware of the products
described in this document without prior notice. Reproduction,
transfer, distribution or storage of part or all of the contents in this
document in any form is prohibited without prior permission of the
manufacturer. All trademarks acknowledged.