Installation guide

ManualsBrandsNone ManualsLighting08239204240

Figure 16

Blade Balancing

All blades are grouped by weight. Because nat-

ural woods vary in density, the fan may wobble

even though the blades are weight matched. The

following procedure should correct most fan

wobble. Check after each step.

1. Check that all blades are securely mounted

to the blade brackets with the locking mech-

anisms engaged.

2. Run the fan for ten minutes. If the fan con-

tinues to wobble please contact Customer

Service and a balacing kit will be sent to you

at no charge.

Attaching the Light

Fixture/Glass Shades

CAUTION - To reduce the risk of electric

shock, disconnect the electrical supply circuit

to the fan before installing the light xture.

1. Loosen the three serrated head screws on

the switch cup cover of the light kit tter

(Figure 16).

2. Connect the wires from the light kit tter

to the wires from the switch cup of the fan

TO REDUCE THE RISK OF PERSONAL INJURY,

DO NOT BEND THE BLADE HOLDERS WHILE

INSTALLING, BALANCING THE BLADES, OR

CLEANING THE FAN. DO NOT INSERT FOREIGN

OBJECTS BETWEEN ROTATING BLADES.

motor assembly by connecting the molded

adaptor plugs together (blue to black, white

to white). Carefully tuck all wires and splic-

es into the switch cup.

3. Align the three serrated head screws on the

switch cup cover of the light kit tter with

the three key slots in the switch cup. Make

sure the notch in the switch cup cover of the

light kit tter clears the reversing switch in

the switch cup. Position the light kit tter

on the switch cup and turn it clockwise un-

til it locks. Tighten the three serrated head

screws that were loosened in step 1 to se-

cure the light kit tter (Figure 16).

4. Remove the rubber washer, hex nut, bottom

cover and the nial from the light kit tter

(Figure 17).

5. With power off, install the two uorescent

bulbs (Max. 14W, included) by screwing

into the light bulb sockets.

6. Position the glass bowl over the threaded

nipple and pass the fan switch chain through

the side hole in the glass bowl.

7. Re-install the rubber washer and hex nut to

the threaded nipple of the light kit tter to

secure the glass bowl properly.

8. Re-install the bottom cover and nial and

nger tighten the nial.

CAUTION - Be sure that the fan switch chain

does not make contact with the light bulbs.

Summary of content (4 pages)

PAGE 1
Blade Balancing All blades are grouped by weight. Because natural woods vary in density, the fan may wobble even though the blades are weight matched. The following procedure should correct most fan wobble. Check after each step. 1. Check that all blades are securely mounted to the blade brackets with the locking mechanisms engaged. 2. Run the fan for ten minutes. If the fan continues to wobble please contact Customer Service and a balacing kit will be sent to you at no charge.
PAGE 2
Fan Without Light Kit 1. In order to use the fan without the light kit, remove the switch cup cover from the top of the light kit fitter by removing the center hex nut inside the switch cup cover, and then thread the switch cup cover off of the threaded nipple on the top of the light kit fitter. Remove three serrated head screws, 2. Press the plastic plug (provided) into the center hole of the switch cup cover. 3.
PAGE 3
Equilibrar las aspas Todas las aspas se agrupan por peso. Como las maderas naturales varían en densidad, el ventilador puede oscilar aunque las aspas tengan el mismo peso. El siguiente procedimiento corregirá en gran medida la oscilación del ventilador. Verifica después de cada paso. 2. Conecta los cables del soporte del kit de 3. 1. Verifica que todas las aspas estén correctamente montadas en los soportes con los mecanismos de cierre acoplados. 2. Enciende el ventilador durante diez minutos.
PAGE 4
Ventilador sin kit de luces Caja del interruptor Bombillas (incluidas) Boquilla enroscada Arandela de goma Cadena del interruptor del ventilador Tazón de vidrio Tuerca hexagonal Cubierta inferior Remate Figura 17 1.