Instructions / Assembly

ManualsBrandsNone ManualsDomestic Appliances82392052881

1. Carefully unhook the fan from the mount-

ing bracket and align the locking slots of

the ceiling canopy with the two screws in

the mounting plate. Push up to engage the

slots and turn clockwise to lock in place. Im-

mediately tighten the two mounting screws

rmly.

2. Install the remaining two mounting screws

into the holes in the canopy and tighten

rmly.

3. Install the decorative canopy ring by align-

ing the ring’s slots with the screws in the

canopy. Rotate the ring clockwise to lock in

place.

4. You may now proceed to attaching the fan

blades.

LOCKING SLOTS OF CEILING CANOPY ARE

PROVIDED ONLY AS AN AID TO MOUNTING.

DO NOT LEAVE FAN ASSEMBLY UNATTENDED

UNTIL ALL FOUR CANOPY SCREWS ARE EN-

GAGED AND FIRMLY TIGHTENED.

Attaching the

Fan Blades

1. Attach blade to blade bracket using the

screws as shown in gure 14. Please note that

the rubber washers are pre-attached to the

blade bracket. Start a screw into the bracket.

Repeat for the two remaining screws

Attaching the Light

Kit Assembly / Glass

Shade

CAUTION - To reduce the risk of electric

shock, disconnect the electrical supply circuit to

the fan before installing the light kit assembly.

1. Remove the three screws on the switch cup

cover of the light kit assembly (Figure 16).

Slot

Screws

Alignment Post

Blade / Blade

Bracket Assembly

Reversing

Switch

Blue

Black

Notch

Switch Cup

Cover

Light Kit

Assembly

Switch Cup

White

Serrated Head

Screw (3)

Screws

Blade

Bracket

Rubber

Washers

Figure 14

Figure 15

Figure 16

2. Tighten each screw securely.

3. Fasten the blade assembly to the motor by

inserting the alignment post into the slot on

the bottom of the motor and tightening the

blade bracket screws. Please note that the

blade bracket screws are pre-installed into

the blade bracket (Figure 15).

4. Repeat steps 1-3 for the remaining blades.

2. Connect the wires existing the bottom of

switch cup with the light kit assembly by

connecting the molded adaptor connectors

together.

Summary of content (4 pages)

PAGE 1
. Carefully unhook the fan from the mounting bracket and align the locking slots of the ceiling canopy with the two screws in the mounting plate. Push up to engage the slots and turn clockwise to lock in place. Immediately tighten the two mounting screws firmly. LOCKING SLOTS OF CEILING CANOPY ARE PROVIDED ONLY AS AN AID TO MOUNTING. DO NOT LEAVE FAN ASSEMBLY UNATTENDED UNTIL ALL FOUR CANOPY SCREWS ARE ENGAGED AND FIRMLY TIGHTENED. 2.
PAGE 2
3. Secure the light kit assembly to the switch cup using the three screws that were removed in step 1. 7. Re-install the rubber washer, hex nut and bottom cover to the threaded nipple to secure the glass shade properly. 4. Remove the rubber washer, hex nut, bottom cover and the finial from the threaded nipple of the light kit assembly (Figure 17). DO NOT OVER TIGHTEN THE HEX NUT, OVERTIGHTENING THE HEX NUT MAY CAUSE THE GLASS TO BREAK. 3.
PAGE 3
MONTAJE CERCA DEL TECHO 1. Con cuidado desengancha el ventilador del soporte de montaje y alinea las ranuras de cierre de la cubierta del techo con los dos tornillos en la placa de montaje. Alza para enganchar las ranuras y gira de izquierda a derecha para asegurar en su sitio. Ajusta con firmeza los dos tornillos de montaje. LAS RANURAS DE CIERRE DE LA CUBIERTA DEL TECHO SÓLO SIRVEN DE AYUDA DURANTE LA INSTALACIÓN.
PAGE 4
3. Fija el ensamblaje del kit de luces a la caja del interruptor con los tres tornillos retirados en el paso 1. 4. Retira la arandela de goma, la tuerca hexagonal, la cubierta inferior y el remate de la boquilla enroscada del ensamblaje del kit de luces (Figura 17). 7. Reinstala la arandela de goma, la tuerca hexagonal y la cubierta inferior en la boquilla enroscada para asegurar la pantalla de vidrio correctamente. NO APRIETES DEMASIADO LA TUERCA HEXAGONAL, HACERLO PUEDE HACER QUE EL VIDRIO DE ROMPA. 8.