User Manual

ManualsBrandsNor-Lake ManualsRefrigeratorsAdvantEDGE Back Bar Refrigeration

09/13 Rev.G 143594

BACK BAR REFRIGERATION

Installation, Operation and Maintenance Instructions

INSPECTION

When the equipment is received, all items should be carefully checked against the Bill

of Lading to ensure all crates and cartons have been received. Do not sign the freight

bill clear until the freight has been properly inspected for damage. All units should be

inspected for damage including concealed damage by uncrating immediately. If any

damage is found, it should be reported to the carrier at once, noted on the Bill of Lading

and a claim should be filed with the carrier. This equipment has been inspected and

tested in the manufacturing facility and has been crated in accordance with

transportation rules and guidelines. The manufacturer is not responsible for freight loss

or damages.

INSTALLATION

After removing the unit from the packaging, clean the interior and exterior surfaces of

the unit with soap and water and a rinse with clean water. Do not use chlorinated

cleaners on the surfaces as they can cause corrosion.

This unit is designed for indoor use only. Be sure to locate the unit where the floor can

support the weight of the unit and product installed inside of it. The refrigeration system

located at the bottom left of the unit requires free air access for proper operation. Allow

a minimum of two inches between the back of the cabinet and the wall. Do not locate

the unit next to heat generating equipment or in direct sunlight.

Confirm that the proposed electrical outlet has the correct voltage, frequency and

current carrying capacity for the requirements of the unit. This information is noted on

the data plate on the inside left wall of the unit. The unit should be isolated on a circuit.

Do not use an extension cord to get power to the unit. Improper electrical installations

will void the compressor warranty. To prevent shock and fire, be sure the unit is properly

grounded.

Local health codes may require that the unit be sealed to the floor with an NSF

approved silicone sealant if it is not on legs or casters. After the unit is set in its desired

location, simply apply a bead of sealant around the base of the unit and smooth it out.

The shelves and shelf support clips are shipped inside the cabinet. Install the shelf

support clips on the pilasters mounted on the inside walls of the cabinet and set the

shelves on the supports. The shelves are adjustable in ½” increments to suit your

needs.

Summary of content (6 pages)

PAGE 1
BACK BAR REFRIGERATION Installation, Operation and Maintenance Instructions INSPECTION When the equipment is received, all items should be carefully checked against the Bill of Lading to ensure all crates and cartons have been received. Do not sign the freight bill clear until the freight has been properly inspected for damage. All units should be inspected for damage including concealed damage by uncrating immediately.
PAGE 2
OPERATION AND MAINTENANCE This cooler is designed to maintain your product temperature within the most desirable range of +34°F to +38°F. You can expect this temperature with the proper temperature control setting and in a normal environment. It is important to remember that when the product is delivered, it must be placed inside the cooler as soon as possible to avoid excessive warm up. If this happens, it may take many hours for the temperature to be reduced to the desirable range.
PAGE 3
TROUBLESHOOTING Problem Remedy · Check the power cord and make sure it is plugged in and has power. Compressor will not start · Check the temperature controller. If it is in the “OFF” position, turn it clockwise to set a desired temperature. · Move the unit from direct sunlight. · Move the unit away from heating devices. · Install the unit in a well ventilated place, with at least 2 inches of clearance on all sides. Poor performance · Clean the condenser if heavy dust is collected.
PAGE 4
BB SERIES REPLACEMENT PARTS LISTS Model Item Number Part Number Description BB59 BB69 BB79 BB95 1 150315 Compressor 115v X X X X 2 150316 Compressor Start Kit 115v X X X X 3 150206 Condenser Coil X X X X 4 150207 Condenser Fan Motor 115V X X X X 5 150232 Evaporator Coil X X X X 6 150234 Evaporator Fan Motor 115V X X X X 7 150236 Evaporator Fan Blade X X X X 8 150238 Evaporator Fan Guard X X X X 9 150211 Thermostat X X X X 10 150212 Ther
PAGE 5
09/13 Rev.
PAGE 6
09/13 Rev.