GB Migration Guide Decentralised drive technology from SK 300E to SK 200E 11.10.
Decentralised drive technology - from SK 300E to SK 200E Contents Contents ..................................................................................................................................................2 1. Introduction ..................................................................................................................................3 1.1 Overview of components ..........................................................................................................3 1.
Introduction 1. Introduction This document serves for the recoding of drive solutions with SK 300E series frequency inverters to the new model SK 200E. As well as the comparison and recoding of the usual modules in the first part of the document, the middle part deals with the comparison of the connection terminals and the final part describes the dimensions of the devices.
Decentralised drive technology - from SK 300E to SK 200E SK 300E Designation Illustration Components SK 200E Illustration Designation M12 System connector System connectors SK TU4-xxx-M12 MA H10E Motor plug connector SK TIE4-HAN10E Table 1: Overview of components 1.2 Overview of frequency inverters The assignment of the inverter versions according to the supply voltage and the rated power of the devices is summarised below.
Recoding 2. Recoding SK 2xxE series frequency inverters are available in a total of 8 different performance levels (SK 200E, SK 205E, SK 210E, SK 215E, SK 220E, SK225E, SK 230E, SK 235E). In general, a distinction is made between SK 2x0E and SK 2x5E devices.
Decentralised drive technology - from SK 300E to SK 200E Power level: 1 phase 230V/240V ~ SK 300E Designation Part Number SK 300E-370-323-B-(C) 275120370 (275160370) SK TI 0/1 230-(C) SK TI 0/2 230-(C) SK 300E-550-323-B-(C) 275120550 (275160550) SK TI 0/1 230-(C) SK TI 0/2 230-(C) SK 300E-750-323-B-(C) 275120750 (275160750) SK TI 0/1 230-(C) SK TI 0/2 230-(C) SK 300E-111-323-B-(C) 275121100 (275161100) SK TI 0/1 230-(C) SK TI 0/2 230-(C) - SK 2xxE Type / Components Frequency inverter 370 W / ½ hp Connecti
Recoding SK 300E Designation Part Number SK 300E-550-323-B-(C) 275120550 (275160550) SK TI 0/1 230-(C) SK TI 0/2 230-(C) SK 300E-750-323-B-(C) 275120750 (275160750) SK TI 0/1 230-(C) SK TI 0/2 230-(C) SK 300E-111-323-B-(C) 275121100 (275161100) SK TI 0/1 230-(C) SK TI 0/2 230-(C) SK 300E-151-323-B-(C) 275121500 (275161500) SK TI 0/1 230-(C) SK TI 0/2 230-(C) SK 300E-221-323-B-(C) 275122200 (275162200) SK TI 0/1 230-(C) SK TI 0/2 230-(C) - SK 2xxE Type / Components Frequency inverter 550 W / ¾ hp Connecti
Decentralised drive technology - from SK 300E to SK 200E Power level: 3 phase 400V/480V ~ SK 300E Designation Part Number SK 300E-550-340-B-(C) 275120555 (275160555) SK TI 0/1,400-(C) SK TI 0/2,400-(C) SK 300E-750-340-B-(C) 275120755 (275160755) SK TI 0/1,400-(C) SK TI 0/2 400-(C) SK 300E-111-340-B-(C) 275121105 (275161105) SK TI 0/1 400-(C) SK TI 0/2 400-(C) SK 300E-151-340-B-(C) 275121505 (275161505) SK TI 0/1 400-(C) SK TI 0/2 400-(C) SK 300E-221-340-B-(C) 275122205 (275162205) SK TI 0/1,400-(C) SK TI 0/
Recoding SK 300E Designation Part Number SK 300E-301-340-B-(C) 275123005 (275163005) SK TI 0/1,400-(C) SK TI 0/2 400-(C) SK 300E-401-340-B-(C) 275124005 (275164005) SK TI 0/1,400-(C) SK TI 0/2 400-(C) - SK 2xxE Type / Components Frequency inverter 3.0 kW / 4 hp Connection unit Internal brake resistor Frequency inverter 4.
Decentralised drive technology - from SK 300E to SK 200E 2.2 Options and components A distinction is made between the standard IP 55 version and the "coated" IP 66 version. The details for the IP 66 versions are shown in brackets. SK 300E option SK 2xxE option Information Designation Part Number SK CU2-BSC-(C) 275130010 (275170010) Customer Unit Basic I/O 3 digital inputs 1 analog input 0…10V (differential input) If the analog input is used as a differential input.
Recoding More recent software files are required for the field bus technology option SK TU4-xxx-(C). SK 300E option SK 2xxE option Designation Part Number Information Designation Part Number SK TU2-PBR-(C) 275130070 (275170070) PROFIBUS DP module Baud rate: 1.
Decentralised drive technology - from SK 300E to SK 200E 2.3 AS Interface Ø If the technology option SK TU2-ASx of the SK 300E is only used as an I/O extension, the SK 20xE must be used with an additional technology option SK TU4-IOE-(C) and the appropriate connection unit SK TI4-TU-BUS-(C). Ø SK 300E with SK TU2-AS1-(C): The "extended string transfer" (refer to BU 0090) cannot be implemented with the SK 22xE.
Recoding 2.4 External braking resistor If the SK 300E application does not have an external braking resistor, an internal braking resistor SK BRI4-x-xxx-xxx must be used with the SK 2xxE If the SK 300E application has an external braking resistor SK BR3-xxx/xxx-TI x/x, the SK 2xxE must be equipped with an external braking resistor SK BRE 4-x-xxx-xxx according to the following table. In this case, the internal braking resistor may not be used with the SK 2xxE.
Decentralised drive technology - from SK 300E to SK 200E 2.
Power and and control terminal connection 3. Power and and control terminal connection 3.1 Power connection PE- socket = 3~ 400V device PE- connector = 3~ 230V device Earth "PE" (connection of mains line) Option Customer unit L1 L2 L3 PE L1 1 ( PE 2 ( PE L - L2 L3 N N U V Motor 3~ 2 Earth "PE" (Additional PE terminal, e.g. for control line, braking resistor) External brake resistor The polarity can be ignored.
Decentralised drive technology - from SK 300E to SK 200E 3.
Power and and control terminal connection SK 300E SK 200E Function / Meaning Terminal bar Terminal number Terminal number Terminal bar SK 2x0E SK BRE3-xxx-xxx Braking resistor SK TI 0/x-(C) 8 Braking resistor SK TI4-x-2xx-x-(C) Braking resistor - -B +B Braking resistor + +B Potentiometer 0...100% switch left-0-right SK CU2-xxx-(C) SK CU4-POT Potentiometer adapter IP 66 SK 2x0E SK 2x5E 43 44 Enable right (e.g. DIN1) 21 - Enable left (e.g.
Decentralised drive technology - from SK 300E to SK 200E SK 300E SK 200E Terminal number Function / Meaning Terminal bar Terminal number Terminal bar SK 2x0E SK TU2-DEV-...
Power and and control terminal connection More recent software files (GSD, EDS) are required for the field bus technology option SK TU4-xxx(C). Information about the master data for the device can be found in Section 5. Further software planning information for conversion to the technology options for SK 2xxE frequency inverters can also be found there. 3.2.1 Details of control terminals for connection units and customer interfaces Control connections: Option Customer unit [21] Dig.
Decentralised drive technology - from SK 300E to SK 200E ASI: Integrated AS interface 24V: 24V power supply AGND: Reference potential for analog signals GND: Reference potential for digital signals DIN: ‚Digital input‘, digital output DOUT: ‚Digital output‘, digital output MB+/-: Control of electro-magnetic brake (105V, 180V, 205V) TF+/-: Motor thermistor (PTC) connection Fig.
Power and and control terminal connection Parameterisation of the customer interface and the field bus technology options can be carried out either via DIP switches or via individual parameters. Further details can be found in the supplementary manuals for the relevant technology option (BU 02x0) or in the manual BU 0200. Mains unit SK CU4-24V-...
Decentralised drive technology - from SK 300E to SK 200E Setpoint converter SK CU4-REL This customer interface can be used instead of the electronic brake rectifier SK CU4-MBR for SK 2x0E applications in which an electro-mechanical brake does not need to be controlled. The setpoint converter SK CU4-REL enables the digital output signal (DO) of the frequency inverter to be converted into potential-isolated relay outputs.
Power and and control terminal connection Electronic brake rectifier, SK CU4-MBR This customer interface must be used for controlling an electro-magnetic brake in SK 2x0E applications and is mounted directly in the connection unit. Fig.
Decentralised drive technology - from SK 300E to SK 200E 3.2.2 Details of control terminals for the technology options I/O extension SK TU4-IOE-(C) With SK 2xxE applications, this technology option can be used to connect additional digital and analog IO signals and is mounted on the frequency inverter with an additional connection unit. Fig.
Power and and control terminal connection AS interface SK TU2-ASx-(C) or SK 22xE-…-(C) Socket I/O 1 Socket I/O 2 1 AUX 24V 2 Dig In 1 3 AUX GND 4 Dig Out 1 5 Dig In 3 1 AUX 24V 2 Dig In 2 3 AUX GND 4 Dig Out 2 5 Dig In 4 Connector PWR Connector AUX 1 AS-i (+) 2 AUX GND 3 AS-i (-) 4 AUX 24V 5 n.c. 1 AUX 24V 2 n.c. 3 AUX GND 4 n.c. 5 n.c. Fig.
Decentralised drive technology - from SK 300E to SK 200E Profibus DP SK TU2-PBR-24V-(C) or SK TU4-PBR-(C) SK 300E SK 2xxE SK TU2-PBR-24V(-C) SK TU4-PBR(-C) SK TI4-TU-BUS(-C) Information bout the other two technology options SK TU2- PBR-(C) and SK TU2-KL-…-(C) for the SK 300E can be found in manual BU 0020. Only the 24V version of the SK 300E is described here. 24V dc connection assignments M8 pin Signal 1 24V DC ±25% 3 GND 4 n.c.
Power and and control terminal connection Potential level: field bus Potential level: system bus Field bus level PROFIBUS DP PB B IN PB A IN 0V-B 1 3 5 7 2 4 6 24V PB B OUT PB A OUT 24V (as for 1) Potential level: DOs System bus level and digital inputs 24V 24V (as for 1) (as for 1) 9 11 8 10 0V-B +5V B RTS (as for 8) 0V GND 0V GND DIN 1 13 15 17 19 21 23 25 27 12 14 16 18 20 22 24 26 28 24V Sys + Sys - 0V GND DIN 3 0V GND 24V DIN 4 0V GND (as for 1
Decentralised drive technology - from SK 300E to SK 200E 4. Dimensions 4.1 Frequency inverter - motor mounted 4.1.1 Frequency inverter SK 300E Motor type Motor output [kW] 71 L/4, /2 0.37 / 0.55 80 S/4 /2 0.55 / 0.75 90 S/6 Size SK 300E g g1 m o p 138 194 214 214 156 156 189 214 236 156 0.75 176 194 214 276 156 80 L/2 1.1 156 211 283 236 196 80 L/40 1.1 156 211 283 236 196 90 S/2, /4 1.5 / 1.1 176 216 283 276 196 Size 1 Size 2 Weight (FI only) 4.
Dimensions 4.1.2 Frequency inverter SK 2xxE n p g1 ∅g o Size FI Size I Housing dimensions SK 2xxE / Motor Motor type ∅g g1 Size 71 * 145 201 214 Size 80 165 195 236 Size 90 S / L 183 200 251 / 276 Size 100 201 209 306 Size 80 165 202 236 183 207 Size 90 S / Size II L n o 236 p Weight of SK 2xxE without motor Approx. [kg] 156 3.0 176 4.1 251 / 276 266 Size 100 201 218 306 Size 112 228 228 326 all dimensions in [mm] * incl.
Decentralised drive technology - from SK 300E to SK 200E 4.2 Frequency inverter - wall-mounting 4.2.1 Frequency inverter SK 300E with WMK-DA1 SK 300E side view SK 300E with wall-mounting kit SK WMK-DA1 and HARTING plug connector SK 300E front view Motor output [kW] Size SK 300E g m p Weight(FI only) 230V/240V à 0.37 - 0.75 400V/480V à 0.55 – 1.5 Size 1 155 215 160 4.0 230V/240V à 1.1 – 2.2 400V/480V à 2.2 - 4 Size 2 185 283 200 8.4 all dimensions in [mm] and approx.
Dimensions 4.2.2 Frequency inverter SK 2xxE with SK TIE4-WMK-1 Adapter plate Device type Size Part Number Size I à SK TIE4-WMK-1 275 274 000 Size II à SK TIE4-WMK-1 275 274 000 Housing dimensions SK 2xxE g2 n p 130.5 236 156 Wall-mounting kit SK TIE4-WMK-1 d 266 ∅ 3.5 180 137.5 e total weight Approx. [kg] 64 176 5.5 4.6 Table 20: Dimensions of SK 2xxE, wall-mounted 4.3 4.3.
Decentralised drive technology - from SK 300E to SK 200E 4.3.2 Braking resistors (external braking resistors) If the SK 300E which is to be replaced is not equipped with a braking resistor, in general an internal brake resistor type SK BR14 must be provided for the SK 2xxE. However, if a braking resistor was fitted on the SK 300E, for the SK 2xxE a corresponding braking resistor type SK BRE4 must be used in place of the internal braking resistor SK BRI4.
Additional information and documents 5. Additional information and documents In addition to this document, data sheets, manuals, mounting instructions and flyers are available for the products described. Manuals Basic information about the frequency inverters can be found in the relevant manuals for the frequency inverter series (e.g. BU 0200 for SK 2xxE). Further information concerning special technology options (e.g.
Decentralised drive technology - from SK 300E to SK 200E List of illustrations Fig. 1: Assignment of connection unit SK TI 0/x-(C) for SK 300E 15 Fig. 2: Assignment of the connection unit SK TI4-x-2xx-x-(C) for SK 2xxE 15 Fig. 3: Control terminals for connection unit SK TI 0/x-(C) for SK 300E 19 Fig. 4: Control terminals for customer interface SK CU2-BSC-(C) for SK 300E 19 Fig. 5: Control terminals for customer interface SK CU2-BSC-(C) for SK 300E 19 Fig.
Additional information and documents List of tables Table 1: Overview of components 4 Table 2: Overview of frequency inverters - Power levels 4 Table 3: Overview of connection units 4 Table 4: Overview of SKL 2xxE performance levels 5 Table 5: 1 phase 230V/240V ~ 6 Table 6: 3 phase 230V/240V ~ 7 Table 7: 3 phase 400V/480V ~ 9 Table 8: Overview of options 1 10 Table 9: Overview of options 2 11 Table 10: Overview of AS interface options 12 Table 11: Overview of external braking resistors
