User Manual

ManualsBrandsNORD Drivesystems ManualsFor the carTI 275900190

Technical Information / Datasheet

PROFINET IO Bus module SK TU3-PNT

1.0 Erstausgabe / first issue 4913 Rck TI 275900190 GB

version reason for change(s) issue name document speech

Pos: 1 /T ec hnis che I nf or mat i o n en/ SK xU x - Bus - Er weiter ung en/PR OFIN ET I O/ SK TU 3-PNT / 275900190 / Basisinformationen [SK TU3-PNT] @ 4 \mod_138 5370630863_388.docx @ 10637 6 @ 555 @ 1

SK TU3-PNT

Part number: 275 900 190

PROFINET IO

- External Bu s – Interface

NOTICE

Validity of this document

This document is only valid in combination with the operating instructions for the relevant frequency inverter. All

of the information that is relevant for a safe start-up of this module and the frequency inverter is only available

under these conditions.

Scope of delivery

1 x Module SK TU3-PNT

Field of us e

Technology unit for connecting a frequency inverter (SK 5xxE) to a PROFINET IO field bus. The

module must be directly plugged into the technology slot of the frequency inverter.

Technical data

Module

Temperature range 0 °C … 40 °C Vibration resistance 2M1

Temperature class Class 3K3 Firmware version V1.2 R0

Protection cl as s IP20 Hardware version AA

Suppl y voltage 24 V ± 20 %, ≈ 100 mA

Reverse polarity

protected

Dimensions [mm] H x W x D: 27 x 73 x 101

Summary of content (8 pages)

PAGE 1
Technical Information / Datasheet Pos : 1 /T ec hnis che Infor mationen/SK xU x - Bus - Er wei ter ung en/PR OFIN ET IO/SK TU3- PNT / 275900190 / Basisinfor mationen [SK TU 3-PNT ] @ 4\mod_1385370630863_388.doc x @ 106376 @ 555 @ 1 Part number: 275 900 190 SK TU3-PNT ® PROFINET IO - External Bus – Interface NOTICE Validity of this document This document is only valid in combination with the operating instructions for the relevant frequency inverter.
PAGE 2
PROFINET IO Bus module – SK TU3-PNT Bus specification EtherNet/IP Max. 100 MBaud Cable Min. Ethernet CAT-5 Electrical isolation 500 Veff Max.
PAGE 3
PROFINET IO Bus module – SK TU3-PNT Installing Note Installing the technology unit Modules should not be inserted or removed unless the device is free of voltage. The slots may only be used for the intended modules. Installation of a technology unit separate from the frequency inverter is not possible. It must be connected directly to the frequency inverter. The technology units must be installed as follows: 1. Switch off the mains voltage, observe the waiting period. 2.
PAGE 4
PROFINET IO Bus module – SK TU3-PNT Configuration Configuration of the module for remote maintenance is carried out via the DIP switches. The DIP - switch settings are read after a "Power On" of the module. DIP switch 12 11 10 X X X 9 8 7 6 Meaning 5 4 3 2 1 No function Access rights for remote maintenance 0 Only read access to parameters possible. 1 Read and write access to parameters possible. TCP/IP open connection. 1 Secure TCP/IP connection. 1. (DIP 1 - 9) No function 2.
PAGE 5
PROFINET IO Bus module – SK TU3-PNT PROFINET-specific LED RUN (Ethernet State) OFF Meaning Flashing green No connection to PROFINET IO controller No parameter communication No process data communication Green ON BF (Ethernet Error) OFF No operating voltage Initialisation Flashing red Red ON Parameter communication active Process data communication active Double-flashing red (2 x 0.25 s,+ 1sec pause) Meaning No error No process data communication à e.g.
PAGE 6
PROFINET IO Bus module – SK TU3-PNT Error messages Error messages from the module - present errors or archived messages relating to the last error - can be read out via the module parameter (P170). The error messages are lost if the module is switched off. Error Meaning Remarks 100.0 EEPROM error EMC fault, module defective 102.0 Timeout via P151/P513 monitoring 103.0 System bus BUS OFF No 24V supply to the bus, connections not correct 104.
PAGE 7
PROFINET IO Bus module – SK TU3-PNT Parameters Frequency inverter: The following frequency inverter parameters must be adapted for setting up communication between the frequency inverter and the bus module (for details see frequency converter manual).
PAGE 8
PROFINET IO Bus module – SK TU3-PNT Parameter access and diagnosis The NORD CON software and optional control units such as the SK PAR-3H parameter box provide convenient access to the parameters of the module and allow status information to be read out. SK TU3Access via diagnosis socket RJ12-SK 5xxE SK TU4- SK CU4- / SK TU4- Access via RJ12-Bus diagnosis socket connection unit SK TI4-TU-BUS(-C) Access via RJ12-Frequency inverter diagnosis socket , if connected to module via system bus.