Datasheet

ManualsBrandsNordic Power ManualsExternal Plug In AdaptersPower Supply 12 ... 24 V 2.4 A/2.3 A/2.2 A/2.1 A/2 A/1.95 A/1.9 A/1.85 A/1.8 A/1.75 A/1.7 A/1.65 A

AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS

Ver: 1 Date: 2011-05-28

AMPLUS

AM09262 Page

SPECIFICATION

AM0055A-H

(output from 12Vd.c. to 24Vd.c., max. 40 watt)

SWITCHING ADAPTOR

SPECIFICATIONS

Summary of content (8 pages)

PAGE 1
SPECIFICATION AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS AM0055A-H (output from 12Vd.c. to 24Vd.c., max.
PAGE 2
SPECIFICATION AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS Prepared by: Checked by: Approved by: TABLE OF CONTENTS 1. SCOPE 2. SPECIFICATION NUMBER 3. ENVIRONMENTAL REQUIREMENTS 4. INPUT REQUIREMENTS 5. INTRODUCTION 6. DC INSULATION RESISTANCE 7. DIELECTRIC WITHSTAND-VOLTAGE 8. MAIN FUSE 9. INRUSH CURRENT 10. TIME SEQUENCE 11. EFFICIENCY 12. SAFETY STANDARD 13. RFI EMISSION 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS 15. RELIABILITY 16. OUTLOOK DRAWING 17. NAME PLATE 18.
PAGE 3
SPECIFICATION AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS 1. SCOPE This document is applied to AM0055A-H(09262H) model for S.M.P.S 2. SPECIFICATION NUMBER AMPLUS part number : Customer part number : AM0055A-H(09262H) 3. ENVIRONMENTAL REQUIREMENTS Operating temperature: 0 -- 40 Storage temperature :-25 -- +85 Operating humidity : 30% -- 95% Storage humidity : 30% --98% Operating bar : 1BAR 4.
PAGE 4
SPECIFICATION AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS The S.M.P.S should not be fired or emitted smoke by protection when the circuit is short. The S.M.P.S can be changeable output voltage by changeable slot. 6. DC INSULATION RESISTANCE Input – Output : 50MΩminimum (at 500VDC) Input – Body metal : 50MΩminimum (at 500VDC) 7. DIELECTRIC WITHSTAND - VOLTAGE Input – Output : 3750VAC minimum (2s) Input – Body metal : 3750VAC minimum (2s) 8. MAIN FUSE Input fuse is 3.15A 250V 9.
PAGE 5
SPECIFICATION AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS 12. SAFETY STANDARD To meet ETL-UL1950,CETL-C22.2 NO.950, GS-DIN EN60950 AS/NZS 4665.1 : 2005, EuP 2005/32/EC 13. RFI EMISSION EN55022: 2006+A1 EN61000-3-2: 2000 EN61000-3-3: 1995+A1 EN55024: 1998+A1+A2 FCC PART 15 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS RATED OUTPUT (V) 12 13 14 15 16 17 18 19 20 21 22 23 24 Rated current(A) 2.5 2.4 2.3 2.2 2.1 2.0 1.95 1.9 1.85 1.8 1.75 1.7 1.65 Max. output voltage(V) 12.
PAGE 6
SPECIFICATION AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS 15. RELIABILITY TESTING A. DC OUTPUT CORD PUSH/PULL TEST OF I/O CONECTOR SIDE Test condition: 8kgf X10sec at Y axis; 5kgfX10sec at other 4 direction verticality RESULT: No cutting inner wire is acceptable 5kgfx10s 8kgfx10s 5kgfx10s 5kgfx10s 5kgfx10s B. DC OUTPUT CORD PUSH/PULL TEST OF ADAPTOR SIDE Test condition: 8kgf X10sec at 5 direction verticality RESULT: No cutting inner wire is acceptable C.
PAGE 7
SPECIFICATION AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS E. INDIVIDUAL DROP TEST Test condition: 6 face, each face 1 time 70 cm, on the 5mm wooden board. RESULT: Without opening of case and crack, etc. electric characteristic shall be satisfied. light crack after test is acceptable. F. LOW TEMPERATURE STORAGE TEST Keep on -30 (Packing) for 168 hours, and check the action after 3 hours in 25 . RESULT: All normal function and meet specification. G.
PAGE 8
SPECIFICATION AM 0055H (09262H) SWITCHING ADAPTOR SPECIFICATIONS 16.