SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS 04151A(AM10268)—20W CEC SWITCHING ADAPTOR SPECIFICATIONS RD Ver: 0 11 Date: 2011/2/22 AMPLUS AM10268.
SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS Prepared by: Checked by: Approved by: TABLE OF CONTENTS 1. SCOPE 2. SPECIFICATION NUMBER 3. ENVIRONMENTAL REQUIREMENTS 4. INPUT REQUIREMENTS 5. INTRODUCTION 6. DC INSULATION RESISTANCE 7. DIELECTRIC WITHSTAND-VOLTAGE 8. MAIN FUSE 9. INRUSH CURRENT 10. TIME SEQUENCE 11. EFFICIENCY 12. SAFETY STANDARD 13. RFI EMISSION 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS 15. RELIABILITY 16. OUTLOOK DRAWING 17. NAME PLATE 18.
SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS 1. SCOPE This document is applied to 04151A(AM10268) model for S.M.P.S 2. SPECIFICATION NUMBER AMPLUS part number : 04151A(AM10268) Customer part number: 3. ENVIRONMENTAL REQUIREMENTS Operating temperature: 0 -- 40 Storage temperature Operating humidity Storage humidity Operating bar :-25 -- +85 : 30% -- 95% : 30% --98% : 1BAR 4.
SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS The S.M.P.S should not be fired or emitted smoke by protection when the circuit is short. The S.M.P.S can be changeable output voltage by changeable slot. 6. DC INSULATION RESISTANCE Input – Output : 50MΩminimum (at 500VDC) Input – Body metal : 50MΩminimum (at 500VDC) 7. DIELECTRIC WITHSTAND - VOLTAGE Input – Output : 3750VAC minimum (2s) Input – Body metal : 3750VAC minimum (2s) 8. MAIN FUSE Input fuse is 2.5A/250V 9.
SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS 11. EFFICIENCY The efficiency of the S.M.P.S must be satisfied the maximum 84%. 12. SAFETY STANDARD To meet ETL-UL1950,CETL-C22.2 NO.950, GS-DIN EN60950 AS/NZS 4665.1 : 2005, EuP 2005/32/EC 13. RFI EMISSION EN55022: 2006+A1 EN61000-3-2: 2000 EN61000-3-3: 1995+A1 EN55024: 1998+A1+A2 FCC PART 15 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS RATED OUTPUT (V) 5 6 7 8 9 10 11 12 13 14 Rated current(A) 3.0 2.5 2.3 2.1 1.9 1.7 1.6 1.
SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS RATED OUTPUT (V) 15 16 17 18 19 20 21 22 23 24 Rated current(A) 1.2 1.13 1.06 1.0 0.98 0.94 0.9 0.88 0.85 0.83 Max. output voltage(V) 15.5 16.5 17.5 18.5 19.5 20.5 21.5 22.5 23.5 24.5 Min. output voltage(V) 14.5 15.5 16.5 17.5 18.5 19.5 20.5 21.5 22.5 23.5 Ripple & Noise(mV) <150 <150 <150 <150 <150 <150 <150 <150 <150 <150 Over load current(A) >2.3 >2.2 >2.1 >2.0 >1.9 >1.8 >1.7 >1.6 >1.
SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS RESULT: No cutting inner wire is acceptable 60' 60 60' 60' STEP1 STEP2 D. CORD BENDING TEST OF ADAPTOR SIDE Test condition: 60’+60’=1 cycle, 30 cycle/1min, weight = 500g , from step 1 to step 2 continuously Step 1. 500 cycle for difficult bending direction Step 2. 500 cycle for easy bending direction RESULT: No cutting inner wire is acceptable E. INDIVIDUAL DROP TEST Test condition: 6 face, each face 1 time 70 cm, on the 5mm wooden board.
SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS Repeat this cycle until 10 cycle, check the action after an hour in 25 . RESULT: All normal function and meet specification. J. CURRENT- CARRYING OF HIGH VOLTAGE TEST Select power consumption at a standard load condition. The test samples shall be active with input voltage is 280V/50Hz,50 ,48 hours, confirm its operation after left in the standard condition for 1 hour. RESULT:any case deformation, smoking, or burn by heat should not be found.
SPECIFICATION AM04151A SWITCHING ADAPTOR SPECIFICATIONS 16. OUTLOOK DRAWING RD Ver: 0 11 Date: 2011/2/22 AMPLUS AM10268.
