SPECIFICATION AM 9820A SWITCHING ADAPTOR SPECIFICATIONS AM9820A(09261)--12W CEC SWITCHING ADAPTOR SPECIFICATIONS RD Ver: 0 11 Date: 2011/2/22 AMPLUS AM09261.
SPECIFICATION AM 9820A SWITCHING ADAPTOR SPECIFICATIONS Prepared by: Checked by: Approved by: TABLE OF CONTENTS 1. SCOPE 2. SPECIFICATION NUMBER 3. ENVIRONMENTAL REQUIREMENTS 4. INPUT REQUIREMENTS 5. INTRODUCTION 6. DC INSULATION RESISTANCE 7. DIELECTRIC WITHSTAND-VOLTAGE 8. MAIN FUSE 9. INRUSH CURRENT 10. TIME SEQUENCE 11. EFFICIENCY 12. SAFETY STANDARD 13. RFI EMISSION 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS 15. RELIABILITY 16. OUTLOOK DRAWING 17. NAME PLATE 18.
SPECIFICATION AM 9820A SWITCHING ADAPTOR SPECIFICATIONS 1. SCOPE This document is applied to AM9820A(09261) model for S.M.P.S 2. SPECIFICATION NUMBER AMPLUS part number : AM9820A(09261) Customer part number: 3. ENVIRONMENTAL REQUIREMENTS Operating temperature: 0 -- 40 Storage temperature Operating humidity Storage humidity Operating bar :-25 -- +85 : 30% -- 95% : 30% --98% : 1BAR 4.
SPECIFICATION AM 9820A SWITCHING ADAPTOR SPECIFICATIONS The S.M.P.S should not be fired or emitted smoke by protection when the circuit is short. 6. DC INSULATION RESISTANCE Input – Output : 50MΩminimum (at 500VDC) Input – Body metal : 50MΩminimum (at 500VDC) 7. DIELECTRIC WITHSTAND - VOLTAGE Input – Output : 3750VAC minimum (2s) Input – Body metal : 3750VAC minimum (2s) 8. MAIN FUSE Input fuse is 1.6A 250V 9. INRUSH CURRENT Peak inrush current shall be limited to 10A for a cold start 10.
SPECIFICATION AM 9820A SWITCHING ADAPTOR SPECIFICATIONS 13. RFI EMISSION EN55022: 2006+A1 EN61000-3-2: 2000 EN61000-3-3: 1995+A1 EN55024: 1998+A1+A2 FCC PART 15 14. OUTPUT RATED & ELECTRICAL SPECIFICATIONS 3 5 6 9 10 12 15 16 18 24 Rated current(A) 1.5 1.8 1.6 1.1 1.0 0.9 0.75 0.7 0.65 0.5 Max. output voltage(V) 3.6 5.5 6.5 9.5 10.5 12.5 15.5 16.5 18.5 24.5 Min. output voltage(V) 2.8 4.5 5.5 8.5 9.5 11.5 14.5 15.5 17.5 23.
SPECIFICATION AM 9820A SWITCHING ADAPTOR SPECIFICATIONS B. DC OUTPUT CORD PUSH/PULL TEST OF ADAPTOR SIDE Test condition: 8kgf X10sec at 5 direction verticality RESULT: No cutting inner wire is acceptable C. CORD BENDING TEST OF I/O CONECTOR SIDE Test condition: 60’+60’=1 cycle, 30 cycle/1min, weight = 200g , from step 1 to step 2 continuously Step 1. 2000 cycle for difficult bending direction Step 2.
SPECIFICATION AM 9820A SWITCHING ADAPTOR SPECIFICATIONS G. HIGH TEMPERATURE STORAGE TEST Keep on +70 (Packing) for 168 hours, and check the action after 3 hours in 25 . RESULT: All normal function and meet specification. H. HIGH HUMIDITY STORAGE TEST Keep on +45 95%RH (Packing) for 168 hours, and check the action after 3hour in 25 . RESULT: All normal function and meet specification. I.
SPECIFICATION AM 9820A SWITCHING ADAPTOR SPECIFICATIONS 16. OUTLOOK DRAWING RD Ver: 0 11 Date: 2011/2/22 AMPLUS AM09261.
