PURE SINE WAVE DC TO AC POWER INVERTER 60S-12A / 60S-24A 60S-12E / 60S-24E 100S-12A / 100S-24A 100S-12E / 100S-24E 150S-12A / 150S-24A 150S-12E / 150S-24E 200S-12A / 200S-24A 200S-12E / 200S-24E Instruction manual
- P1 -
- P2 -
- P3 -
- P4 -
- P5 -
- P6 -
- P7 -
- P8 -
- P9 -
Sine Wave Inverter Please read this manual carefully before installing and starting up and store it in a safe place. If the device is resold, this instruction manual must be handed over to the purchaser along with the device. Contents 1 Notes on using the instruction manual. . . . . . . . . . . . . . . . . . . . . . . P11 2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. P11 3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes on using the instruction manual 1 Sine Wave Inverter Notes on using the instruction manual Caution! Safety instruction, failure to observe this instruction can cause material damage and impair the function of the device. Supplementary information for operating the device. Caution! Safety instruction relating to a danger from electrical current or voltage. Failure to observe this instruction can cause material damage and personal injury and impair the function of the device.
Sine Wave Inverter General safety instructions Use the device only as intended. Do not operate the device in a damp or wet environment. Do not operate the device in areas that are potentially explosive. Maintenance and repair work must only be carried out by qualified personnel who are familiar with the risks involved and the relevant regulations. 2.2 Safety when installing the device Ensure that the device has a firm foundation.
Scope of delivery Sine Wave Inverter Caution! Note the following basic safety information when using electrical devices: – Electric shock – Fire hazard – Injury Operate the device only if you are certain that the housing and the cables are undamaged. Make sure the air inlets and outlets of the device are not covered. Ensure good ventilation. Do not connect the 115V/230 V output of the inverter (fig. 3, page 2 / fig. 12, page 6) to an appliance not using the source of 115V/230 V.
Sine Wave Inverter Technical description 5 Technical description The inverters can be operated wherever there is a 12 V DC supply (60S12A/E, 100S-12A/E, 150S-12A/E, 200S-12A/E) or a 24 V DC supply (60S24A/E, 100S-24A/E, 150S-24A/E, 200S-24A/E). With its low weight and the compact design, the inverter can be easily installed into Camping mobiles, commercial vehicles or motor and sailing yachts.
Installing the inverter Sine Wave Inverter For making and testing the electrical connection the following tools are required: Crimping tool 3 different flexible cable connections. The required cable diameter can be taken from the table in the section „Connecting the inverter“ on page 16. Various terminals, multicore cable ends For fixing the inverter you need the following mounting devices: Screws (M4) with spacers and self-locking nuts or sheet metal screws resp. wood screws. Mounting size (fig.
Sine Wave lnverter Connecting the inverter 6.3 Installing the inverter Adjust the inverter to the chosen installation place and mark the fixing points. Fix the inverter by using the self-chosen fixing method. 7 Connecting the inverter 7.1 General instructions In case the inverter is installed into vehicles or boats it has to be connected to the chassis (ground). On building up an electricity supply network the safety regulations according to the VDE 0100 standard are to be kept.
Using the inverter Sine Wave lnverter inches of the battery. Connect the positive cable to the red positive terminal. Warning! In order for the integrated residual current-operated protective device of the 60S-12A/E, 60S-24A/E, 100S-12A/E, 100S-24A/E, 150S-12A/E, 150S-24A/E, 200S-12A/E and 200S-24A/E inverters to work properly, the earth connection of the inverter (fig. 4, page 2 / fig. 14, page 7) must be electrically connected to the chassis of the vehicle or boat.
Sine Wave lnverter Using the inverter 150S-24A/E, 200S-24A/E), the OVER-LOAD“ LED (fig. 1.3, page 1 / fig. 10.4, page 5) illuminates and an audible signal is given. The inverter shuts down automatically in case of a battery voltage down to 10 V resp. 20 V. If the device overheats, the inverter shuts down – the “OVER TEMP” LED (fig. 1.4, page 1 / fig. 10.5, page 5) lights up. If this happens, switch off the inverter via the switch. Ensure that the inverter is sufficiently ventilated Wait for approx.
Rectifying faults 9 Sine Wave lnverter Rectifying faults Fault No output voltage, LED not Illuminated Cause Bad connection between battery and inverter. Internal fuses defect. Remedy Check the cables and contact In this case send the unit back to supplier. Switch off the inverter and the power consuming units. Wait for approx. 5 - 10 minUtes and switch on the inverter only. Reduce the loading and ensure a better ventilation for the inverter. Then switch back on the consuming unit.
Sine Wave lnverter 10 Cleaning and caring for the inverter Cleaning and caring for the inverter Caution! Do not use sharp or hard objects for cleaning as these may damage the device. Occasionally clean the device with a damp cloth. 11 Guarantee Our general guarantee conditions apply. If the product is defective, please send it back to us.
Technical data 13 Sine Wave lnverter Technical data 600W Pure Sine Wave Inverter Item number 60S-12E 60S-24E 60S-12A 60S-24A Rated input voltage 12 V DC 24 V DC 12 V DC 24 V DC Constant output power Peak output power (a max. of 10 min.) Maximum input current Output voltage Output frequency 600 W 1000 W (650 W) 80A 40A 40A 230VAC +/- 3% 115VAC +/- 3% 50 Hz or 60Hz to be specified Output Wave Form Total Harmonic Distortion No Load Current 80A Pure Sine Wave 3% <0.8A <0.6A <0.6A <0.
Sine Wave lnverter 13 Technical data Technical data 1000W Pure Sine Wave Inverter Item number Rated input voltage 100S-12E 100S-24E 100S-12A 100S-24A 12 V DC 24 V DC 12 V DC 24 V DC Constant output power Peak output power (a max. of 10 min.) Maximum input current Output voltage Output frequency 1000 W 2000 W (1200 W) 160A 80A Output Wave Form Total Harmonic Distortion No Load Current 160A 80A 230VAC +/- 3% 115VAC +/- 3% 50 Hz or 60Hz to be specified Pure Sine Wave 3% <1.2A <0.8A <0.
Technical data 13 Sine Wave lnverter Technical data 1500W Pure Sine Wave Inverter Item number Rated input voltage 150S-12E 150S-24E 150S-12A 150S-24A 12 V DC 24 V DC 12 V DC 24 V DC Constant output power Peak output power (a max. of 10 min.) Maximum input current Output voltage Output frequency 1500 W 3000 W (1800 W) 200A 100A 100A 230VAC +/- 3% 115VAC +/- 3% 50 Hz or 60Hz to be specified Output Wave Form Total Harmonic Distortion No Load Current 200A Pure Sine Wave 3% <1.
Sine Wave lnverter 13 Technical data Technical data 2000W Pure Sine Wave Inverter Item number Rated input voltage 200S-12E 200S-24E 200S-12A 200S-24A 12 V DC 24 V DC 12 V DC 24 V DC Constant output power Peak output power (a max. of 10 min.) Maximum input current Output voltage Output frequency 2000 W 4000 W (2200 W) 240A 120A 120A 230VAC +/- 3% 115VAC +/- 3% 50 Hz or 60Hz to be specified Output Wave Form Total Harmonic Distortion No Load Current 240A Pure Sine Wave 3% <1.
902SI200000005
