3G10WV – HSPA 7.
Thank you for purchasing NetComm’s HSPA Wi-Fi Router with Voice Preface The purpose of this manual is to provide you detailed information on the installation, operation and application of your HSPA 7.2Mbps Wi-Fi Router with Voice. Important Notice and Safety Precaution • • • • • Before servicing or disassembling this equipment, always disconnect all power or telephone lines from the device. Use an appropriate power supply, preferably the supplied power adapter, with an output of DC 12V 1.
Table of Contents Thank you for purchasing NetComm’s HSPA Wi-Fi Router with Voice..................................................... 2 Preface............................................................................................................................................................2 Important Notice and Safety Precaution.............................................................................................................2 1 – Introduction...........................................
6.3 Simple Network Time Protocol (SNTP)......................................................................................................40 6.4 Access Control.......................................................................................................................................41 6.4.1 Services.....................................................................................................................................41 6.4.2 IP Addresses...........................................
Introduction
Introduction With the increasing popularity of the 3G standard worldwide, this HSPA 7.2Mbps Wi-Fi Router with Voice provides you with triple-band coverage through expanding cellular networks throughout the world. By following the simple step-by-step instructions found on the Connection Manager USB key, you can share your connection with multiple wireless and wired devices using the 3G network. Integrating a Sierra Wireless HSPA module, this Router downloads turbo speeds of up to 7.2Mbps.
1.1 • • • • • • • • • • • • • • • • • • • • 1.2 Features This HSPA Wi-Fi Router with Voice allows you to share your 3G connection with multiple wireless or wired devices Provides you with worldwide coverage through triple-band HSUPA/HSDPA/UMTS (850 / 1900 / 2100MHz), quad-band EDGE/GSM (850 / 900 / 1800 / 1900 MHz) Embedded multi-mode HSUPA/HSDPA/UMTS/EDGE/GPRS/GSM module 1 x RJ11 port for voice calling over the 3G network via a connected standard Analogue Telephone (not included). Integrated 802.
3G10WV – FRONT BEZEL GRAPHICS 1.3 The background colour of the bezel must be printed WHITE INK LED Indicators All type and graphics print WHITE INK onto background colour of CMYK C100/M56/Y0/K16 The front panel LED indicators are shown followed detailed explanations in the Lights and product keyline in arethis for illustration positioning and purposes onlyby – do not output table below.
1.4 Rear Panel The rear panel contains the ports for data and power connections. 1 (1) (2) (3) (4) (5) (6) (8) (9) 2 3 4 5 6 7 8 Main 3G Antenna (removable, SMA connection) Power jack for DC power input (12VDC / 1.
Quick Setup
Quick Setup 2.1 Setup Procedure NOTE: Chapters 3 through 8 explain how to setup and use the WUI These steps explain how to quickly setup your 3G router: 1: Attach the two 3G antennas provided to the ports marked Main and AUX on the back of the router. The antennas should be screwed in a clockwise direction. 2: Insert your SIM card (until you hear a click) into the USIM slot at the back of the Router. 3: Connect the yellow networking cable to one of the yellow ports found at the back of the Router.
Web User Interface
Web User Interface This section describes how to access the device via the web user interface using a web browser such as Microsoft Internet Explorer (version 5.0 or later). 3.1 Default Settings The following are the default settings for the device. • • • • • • • • Local (LAN) access (username: admin, password: admin) Remote (WAN) access (username: support, password: support) User access (username: user, password: user) LAN IP address: 192.168.1.
3.2 TCP/IP Settings DHCP Mode When your Router powers up, the Dynamic Host Configuration Protocol (DHCP) server (on the device) will start automatically. To set your PC for DHCP mode, check the Internet Protocol properties of your Local Area Connection. You can set your PC to DHCP mode by selecting Obtain an IP address automatically in the dialog box shown below. STATIC IP Mode To configure your Router manually, your PC must have a static IP address within the Router’s subnet.
3.3 Login Procedure NOTE: The default settings can be found in 3.1 Default Settings. To login to the web interface, follow the steps below: 1: Open a web browser and enter the default IP address for the Router in the Web address field. In this case http://192.168.1.1. NOTE: For local administration (i.e. LAN access), the PC running the browser must be attached to the Ethernet, and not necessarily to the device.
3.4 Web User Interface Homepage The web user interface (WUI) is divided into two window panels, the main menu (on the top) and the display screen (on the bottom). The main menu has the following options: Basic, 3G Settings, Wireless, Management, Advanced, Voice and Status. Selecting one of these options will open a submenu with more options. Basic is discussed below while subsequent chapters introduce the other main menu selections.
The following table provides further details. Fields Description Software version The software version of the device. Hardware version The Hardware version of the device Bootloader version The bootloader version of the device. Wireless driver version The wireless driver version of the wireless module. Network The name of or other reference to the mobile network operator. Link Shows the connection status of the current 3G connection.
3G Settings
3G Settings This menu includes 3G service Setup and PIN Configuration. NOTE: Sections 9.3 and 9.4.2 also provide information about the 3G service. 4.1 3G Service Setup Select your 3G service settings according to predefined or custom profiles. Setup instructions are provided in the following sections for your assistance.
4.1.1 Profile Setup Your Service Provider will provide the information required to complete the first time setup instructions below. This includes profile, username and password. Only complete those steps for which you have information and skip the others. 1. If your SIM card is not inserted into the gateway, please turn the gateway off. Then insert the SIM and turn the gateway on. 2. T ype the APN in the APN field.
4.2 PIN Configuration NOTE: If you have entered the incorrect PIN 3 times, your SIM card will be locked for your security. Please call your 3G Provider for assistance. 4.2.1 PIN Code Protection This screen allows for changes to the 3G SIM card PIN code protection settings. PIN code protection prevents the use of a SIM card by unauthorized persons. To use the 3G internet service with this router however, the PIN code protection must be disabled.
PIN Lock On After you are finished using your SIM card for Internet service, you may wish to lock it again. In this case, first go to the 3G Settings - PIN Configuration screen, as shown below. Select PIN lock ON, enter the PIN code twice. You can select Remember PIN code to Yes so you don’t need to input the PIN code every time when the router turns on. Then click Save. After you do so, the following dialog box should appear. You can now return your SIM card to your cellular phone or other mobile device.
4.2.2 PIN Code Change If you wish to change your PIN code for greater security, enable the PIN Code protection. Go to the previous section and follow the procedure listed under PIN Lock On. After locking the SIM card, select PIN Code Change and enter your Old and New PIN codes in the fields provided. Keep in mind you only have 3 attempts before your SIM card is locked. The remaining attempts’ number shows how many attempts left. Contact Telstra if you require assistance.
Wireless
Wireless The Wireless submenu provides access to Wireless Local Area Network (LAN) configuration settings including: • • • • • Wireless network name Channel restrictions (based on country) Security Access point or bridging behaviour Station information 3G10WV HSPA Wi-Fi Router with Voice – 25
5.1 Setup This screen allows you to configure basic features of the wireless LAN interface. You can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. The Wireless Guest Network function adds extra networking security when connecting to remote hosts. Option Description Enable Wireless A checkbox that enables (default) or disables the wireless LAN interface.
5.2 Security This Router includes a number of security options that provides you with a secure connection to a 3G network. State-of-the art security includes: • WEP / WPA / WPA2 data encryption • SPI Firewall • VPN Pass-Through • MAC address IP filtering • Authentication protocols – PAP / CHAP You can authenticate or encrypt your service on the Wired Equivalent Privacy (WEP) algorithm, which provides protection against unauthorized access such as eavesdropping.
Select SSID Your Service Set Identifier (SSID), sets your Wireless Network Name. You can connect multiple devices including Laptops, Desktop PCs and PDAs to your Wireless Router. To get additional devices connected, scan for a network, and locate the SSID shown on your Wireless Security Card. If the SSID does not match, access is denied. Network Authentication This option is used for authentication to the wireless network. Each authentication type has its own settings as illustrated below.
5.3 Configuration The following screen appears when you select Configuration.
Option Description AP Isolation Select On or Off. By enabling this feature, wireless clients associated with the Access Point can be linked. Band The new amendment allows IEEE 802.11g units to fall back to speeds of 11 Mbps, so IEEE 802.11b and IEEE 802.11g devices can coexist in the same network. The two standards apply to the 2.4 GHz frequency band. IEEE 802.11g creates data-rate parity at 2.4 GHz with the IEEE 802.11a standard, which has a 54 Mbps rate at 5 GHz. (IEEE 802.
Option Description 54g Mode Select Auto mode for greatest compatibility. Select Performance mode for the fastest performance among 54g certified equipment. Select LRS mode if you are experiencing difficulty with legacy 802.11b equipment. If this does not work, you may also try 802.11b only mode. 54g Protection In Auto mode, the router will use RTS/CTS to improve 802.11g performance in mixed 802.11g/802.11b networks. Turning protection Off will maximize 802.11g throughput under most conditions.
5.4 MAC Filter This screen appears when Media Access Control (MAC) Filter is selected. This option allows access to be restricted based upon the unique 48-bit MAC address. To add a MAC Address filter, click the Add button shown below. To delete a filter, select it from the table below and click the Remove button. Option Description MAC Restrict Mode Disabled – Disables MAC filtering Allow – Permits access for the specified MAC addresses.
5.5 Wireless Bridge The following screen appears when selecting Wireless Bridge, and goes into a detailed explanation of how to configure wireless bridge features of the wireless LAN interface. Click Save/Apply to implement new configuration settings. Feature Options AP Mode Selecting Wireless Bridge (Wireless Distribution System) disables Access Point (AP) functionality while selecting Access Point enables AP functionality.
5.6 Station Info The following screen appears when you select Station Info, and shows authenticated wireless stations and their status. Click the Refresh button to update the list of stations in the WLAN. BSSID The BSSID is a 48-bit identity used to identify a particular BSS (Basic Service Set) within an area. In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control) address of the AP (Access Point); and in Independent BSS or ad hoc networks, the BSSID is generated randomly.
Management
Management The Management menu has the following maintenance functions and processes: 6.1 Device Settings 6.2 Simple Network Management Protocol (SNMP) 6.3 Simple Network Time Protocol (SNTP) 6.4 Access Control 6.5 Save and Reboot 6.1 Device Settings 6.1.1 Backup Settings The Device Settings screens allow you to backup, retrieve and restore the default settings of your Router. It also provides a function for you to update your Routers firmware. The following screen appears when Backup is selected.
6.1.2 Update Settings The following screen appears when selecting Update from the submenu. By clicking on the Browse button, you can locate a previously saved filename as the configuration backup file. Click on the Update settings to load it. 6.1.3 Restore Default The following screen appears when selecting Restore Default. By clicking on the Restore Default Settings button, you can restore your Routers default firmware settings. To restore system settings, reboot your Router.
6.1.4 Update Firmware The following screen appears when selecting Update Firmware. By following this screens steps, you can update your Routers firmware. Manual device upgrades from a locally stored file can also be performed using the following screen. 1: Obtain an updated software image file 2: Enter the path and filename of the firmware image file in the Software File Name field or click the Browse button to locate the image file.
6.2 Configure SNMP agent on 3G10WV The Simple Network Management Protocol (SNMP) allows a network administrator to monitor a network by retrieving settings on remote network devices. To do this, the administrator typically runs an SNMP management station program such as MIB browser on a local host to obtain information from the SNMP agent, in this case the 3G10WV (if SNMP enabled). An SNMP ‘community’ performs the function of authenticating SNMP traffic.
6.3 Simple Network Time Protocol (SNTP) This screen allows you to configure the time settings of your Router. To automatically synchronize with Internet timeservers, tick the box as illustrated below. The following options should now appear (see screenshot below): First NTP timeserver: Select the required server. Second NTP timeserver: Select second timeserver, if required. Time zone offset: Select the local time zone. Configure these options and then click Save/Apply to activate.
6.4 Access Control The Access Control option found in the Management drop down menu, configures access related parameters in the following three areas: • Services • IP Addresses • Passwords Access Control is used to control local and remote management settings for your Router. 6.4.1 Services The Service Control List (SCL) allows you to enable or disable your Local Area Network (LAN) or Wireless Area Network (WAN) services by ticking the checkbox as illustrated below.
6.4.2 IP Address The IP Address option limits local access by IP address. When the Access Control Mode is enabled, only the IP addresses listed here can access the device. Before enabling Access Control Mode, add IP addresses with the Add button. On this screen, enter the IP address of a local PC which you wish to allow permission. Click Save/Apply to continue.
6.4.3 Passwords The Passwords option configures your account access password for your Router. Access to the device is limited to the following three user accounts: • admin is to be used for local unrestricted access control • support is to be used for remote maintenance of the device • user is to be used to view information and update device firmware Use the fields illustrated in the screen below to change or create your password. Passwords must be 16 characters or less with no spaces.
Advanced Setup
Advanced Setup This chapter explains advanced setup for your Router: 3G10WV HSPA Wi-Fi Router with Voice – 45
7.1 Local Area Network (LAN) This screen allows you to configure the Local Area Network (LAN) interface on your Router. See the field descriptions below for more details. Option Description IP Address Enter the IP address for the LAN interface Subnet Mask Enter the subnet mask for the LAN interface Enable UPnP Tick the box to enable Universal Plug and Play Enable Half-Bridge The HSPA 7.
Enable DHCP Server Relay To relay DHCP requests from the subnet with no DHCP server on it to a DHCP server on other subnets. DHCP Server Relay is disabled by default. To access enable DHCP relay, please un-tick NAT enable first, that means to disable NAT first, and then press save button. The Enable DHCP server Relay option will then show up on the same page as below: Enable Half-Bridge the HSPA 7.
7.2 Network Address Translation (NAT) 7.2.1 Port Forwarding Port Forwarding allows you to direct incoming traffic from the Internet side (identified by Protocol and External port) to the internal server with a private IP address on the LAN side. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. A maximum of 32 entries can be configured. To add a Virtual Server, click the Add button.
Options Description Select a Service User should select the service from the list. Or Or Custom Server Create a customer server and enter a name for the server Server IP Address Enter the IP address for the server. External Port Start Enter the starting external port number (when you select Custom Server). When a service is selected the port ranges are automatically configured. External Port End Enter the ending external port number (when you select Custom Server).
7.2.2 Port Triggering Some applications require specific ports in the Router’s firewall to be open for access by remote parties. Port Triggering opens up the ‘Open Ports’ in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the ‘Triggering Ports’. The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the ‘Open Ports’. A maximum 32 entries can be configured.
Options Description Select an Application User should select the application from the list. or or Custom Application User can enter the name of their choice. Trigger Port Start Enter the starting trigger port number (when you select custom application). When an application is selected, the port ranges are automatically configured. Trigger Port End Enter the ending trigger port number (when you select custom application).
7.3 Security 7.3.1 IP Filtering Your Router can be secured with IP Filtering or Parental Control functions. The IP Filtering screen sets filter rules that limit incoming and outgoing IP traffic. Multiple filter rules can be set with at least one limiting condition. All conditions must be fulfilled when individual IP packets pass filter. Outgoing IP Filter The default setting for Outgoing traffic is ACCEPTED. Under this condition, all outgoing IP packets that match the filter rules will be BLOCKED.
Options Description Filter Name The filter rule label Protocol TCP, TCP/UDP, UDP or ICMP Source IP address Enter source IP address Source Subnet Mask Enter source subnet mask Source Port (port or port:port) Enter source port number or port range Destination IP address Enter destination IP address Destination Subnet Mask Enter destination subnet mask Destination port (port or port:port) Enter destination port number or range Click Save/Apply to save and activate the filter.
7.3.2 Parental Control This Parental Control allows you to restrict access from a Local Area Network (LAN) to an outside network through the Router on selected days at certain times. Make sure to activate the Internet Time server synchronization as described in section 6.3 SNTP, so that the scheduled times match your local time. Click Add to display the following screen. See instructions below and click Save/Apply to apply the settings.
7.4 Routing 7.4.1 Default Gateway Default Gateway, Static Route and Dynamic Route settings can be found in the Routing link as illustrated below. If the Enable Automatic Assigned Default Gateway checkbox is selected, this device will accept a default Gateway assignment. If the checkbox is not selected, a field will appear allowing you to enter the static default gateway and/or WAN interface, then click Save/Apply.
7.4.2 Static Route The Static Route screen displays the configured static routes. Click the Add or Remove buttons to change settings. Click the Add button to display the following screen. Enter Destination Network Address, Subnet Mask, Gateway IP Address and/or WAN Interface. Then click Save/Apply to add the entry to the routing table.
7.4.3 Dynamic Route To activate this option, select the Enabled radio button for Global RIP Mode. To configure an individual interface, select the desired RIP version and operation, followed by placing a check in the Enabled checkbox for that interface. Click Save/Apply to save the configuration and to start or stop dynamic routing. 7.5 7.5.
7.5.2 Dynamic DNS The Dynamic DNS service allows a dynamic IP address to be aliased to a static hostname in any of a selection of domains, allowing the router to be more easily accessed from various locations on the internet. Note: The Add/Remove buttons will be displayed only if the router has been assigned an IP address from the remote server. To add a dynamic DNS service, click the Add button and this screen will display.
Voice 3G10WV HSPA Wi-Fi Router with Voice – 59
Voice The 3G10WV HSPA 7.2Mbps Wi-Fi Router with Voice allows you to make telephone calls over the 3G Mobile/ Cellular Telephone network using a standard Analogue Telephone via the built in RJ-11 Phone port. Please refer to the documentation provided by the manufacturer for operating your Analogue Telephone. Note that your SIM card and Mobile service needs to be provisioned for Voice Calling. Please consult with your Network Provider for verification.
Status
Status The Status menu has the following submenus: • Diagnostics • System Log • 3G network • Statistics • Route • ARP • DHCP • PING 62 – 3G10WV HSPA Wi-Fi Router with Voice
9.1 Diagnostics The Diagnostics menu provides feedback on the connection status of the device. The individual tests are listed below. If a test displays a fail status: 1: Click on the Help link 2: Now click Re-run Diagnostic Tests at the bottom of the screen to re-test and confirm the error 3: If the test continues to fail, follow the troubleshooting procedures in the Help screen.
9.2 System Log This function allows you to view system events and configure related options. Follow the steps below to enable and view the System Log. 1: Click Configure System Log to continue. 2: Select the system log options (see table below) and click Save/Apply.
Option Description Log Indicates whether the system is currently recording events. You can enable or disable event logging. By default, it is disabled. Log level Allows you to configure the event level and filter out unwanted events below this level. The events ranging from the highest critical level “Emergency” down to this configured level will be recorded to the log buffer on the Router’s SDRAM.
9.3 3G Status Select this option for detailed status information on your Routers 3G connection. Consult the table on the next page for detailed field descriptions.
Status Description Manufacturer The manufacturer of the embedded 3G module. Model The model name of the embedded 3G module. FW Rev. The firmware version of the 3G module. IMEI The IMEI (International Mobile Equipment Identity) is a 15 digit number that is used to identify a mobile device on a network. FSN Factory Serial Number of the 3G module. IMSI The IMSI (International Mobile Subscriber Identity) is a unique 15-digit number used to identify an individual user on a GSM or UMTS network.
Status Description Signal Level (RSSI) 3G Radio Signal Strength Index Value 2~5 6 ~ 10 11 ~ 13 Signal level in dBm -109 ~ -103 -101 ~ -93 -91 ~ -87 14 ~ 17 18 ~ 31 99 -85 ~ -79 -77 ~ -52 unknown 5 Signal bars LED Low Medium High Quality (Ec/Io) The total energy per chip per power density (Ec/Io) value of the active set’s three strongest cells. Network Registration Status Should display as registered with a valid unlocked SIM card. Network Name The 3G internet Service Provider.
9.4 Statistics These screens provide detailed information for: • Local Area Network (LAN) and Wireless Local Area Network (WLAN) • 3G Interfaces NOTE: These statistics page refresh every 15 seconds. 9.4.1 LAN Statistics This screen displays statistics for the Ethernet and Wireless LAN interfaces.
9.4.2 3G Statistics Click 3G network in the Statistics submenu to display the screen below. Service Shows the service type Inbound Octets Number of received octets over the interface. Packets Number of received packets over the interface. Drops Received packets which are dropped. Error Received packets which are errors. Octets Number of Transmitted octets over the interface. Packets Number of Transmitted packets over the interface.
9.5 Route Select Route to display the paths the Router has found. Field Description Destination Destination network or destination host Gateway Next hop IP address Subnet Mask Subnet Mask of Destination Flag U: route is up !: reject route G: use gateway H: target is a host R: reinstate route for dynamic routing D: dynamically installed by daemon or redirect M: modified from routing daemon or redirect Metric The ‘distance’ to the target (usually counted in hops).
9.6 ARP Click ARP to display the ARP information. Field Description IP address Shows IP address of host pc Flags Complete Incomplete Permanent Publish HW Address Shows the MAC address of host pc Device Shows the connection interface 9.7 Dynamic Host Configuration Protocol (DHCP) Click DHCP to display the DHCP information.
9.8 PING The PING menu provides feedback of connection test to an IP address or a host name. Input a IP address or a host name, e.g www.google.com and press Submit. The connection test result will be shown as below.
CLI commands Via Telnet 74 – 3G10WV HSPA Wi-Fi Router with Voice
CLI commands via Telnet Show all CLI commands Description: List all available CLI commands that the 3G router supports.
Description: End the telnet session Synopsis: logout Example: > logout Reset/reboot device Description: To reboot the router. Synopsis: reboot Example: > reboot Radio Signal Strength Description: Display the 3G radio signal strength.
System mode: WCDMA PS state: Attached WCDMA band: WCDMA800 GSM band: Unknown WCDMA channel: 4436 GSM channel: 65535 GMM (PS) state:REGISTERED NORMAL SERVICE MM (CS) state: IDLE NORMAL SERVICE WCDMA L1 State:L1M_FACH RRC State: CELL_FACH RX level (dBm):-90 IMSI & IMEI read Description: Display the IMSI and IMEI value Synopsis: sierra show --imsi sierra show --imei Example: > sierra show --imsi imsi: 466974800524867 > sierra show --imei IMEI: 354219010024303 Network Information • sierra show --hsdcat Descript
Description: To report the current available and supported network technologies being used. Synopsis: sierra show --mode Example: > sierra show --mode mode: UMTS (Valid values: “GSM”, “GPRS”, “EDGE”, “UMTS”, “HSDPA”, “HSUPA”) • sierra show --registration Description: To display the Network Registration Status, Country code and Network code.
Description: To set and query authentication method (PAP/CHAP/AUTO) for PDP-IP packet data calls if the profile supports.
> sierra set --comp 1 0 enable • sierra show --comp Description: To display the IP header or data compression status. Synopsis: sierra show --comp 1: Custom APN Examples: > sierra show --comp 1 Profile1: IPH is Off, DATA is Off Connect / Disconnect PPP session Description: To connect or disconnect the PPP session. The profile to be used to develop a connection is the latest configured by the sierra set command.
Synopsis: sierra show --PIN-LOCK Example: > sierra show --PIN-LOCK PIN code protection is disabled • sierra show --SIM Description: To display the SIM card status.
> wlan wlan command usage : wlan config [option] wlan security [option] wlan macfilter [option] wlan wds [option] wlan info [option] wlan –help Each option will be explained separately below. Note: The settings changed from these commands take effect immediately and will be updated on the web page 1. Please enable the wireless BEFORE changing other wireless settings. 2. The wlan command will save the configuration into flash memory and the new settings will be saved.
Description: Enable or disable wireless LAN interface. Valid value: 0 or 1 0 – disabled the wireless LAN interface. 1 – enabled the wireless LAN interface. Default value: 1 --hide <0|1> Description: Hide wireless LAN network name (SSID). Valid value: 0 or 1 0 – not hide wireless LAN SSID. 1 – hide wireless LAN SSID Default value: 0 --ssid Description: Set Wireless LAN network name (SSID).
Default value: 0 --mrate Description: Set the wireless LAN Multicast rate. Valid value: 0, 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 (Mbps) 0 means auto Default value: 0 --rts Description: Set the wireless LAN RTS threshold. Valid value: 0~2347 Default value: 234 --frag Description: Set the wireless LAN fragment threshold. Valid value: 256~2346 Default value: 2346 --dtim Description: Set the wireless LAN DTIM interval.
Default value: long Example 1: User wants to enable the wireless LAN, configure the wireless LAN network name (SSID) as “TestAP”, configure wireless LAN channel to 5 and then hide the SSID: wlan config --enable 1 wlan config --ssid “TestAP” wlan config --channel 5 --hide 1 Or merge the above commands wlan config --enable 1 --ssid “TestAP” --channel 5 --hide 1 Configure wireless LAN security Description: Enable or disable and configure the wireless LAN security.
[--nkey2 ] [--nkey3 ] [--keyidx <2|3>] wlan security psk / psk2 / psk2mix [--wpaenc ] [--rekey ] [--pskey <”pskeyStr”>] [--wep ] [--keybit <64|128>] [--nkey2 ] [--nkey3 ] [--keyidx <2|3>] Options: --wep Description: enable or disable WEP encryption --keybit <64|128> Description: Set the WEP encryption strength --nkey1 --nkey2 --nkey3 --nkey4 Description: Set the WEP key.
3G10WV - HSPA 7.2Mbps Wi-Fi Router with Voice USER GUIDE --rekey Description: Set the Group Rekey Interval Default value: 0 --pskey <”pskeyStr”> Description: Set the WPA Pre-Shared Key Valid value: string of 8 ~ 63 characters. Note: 1. wlPreauth can only be used with WPA2. 2. When using WPA-PSK or WPA2-PSK, WPA Pre-Shared Key (pskey) must be set first. 3. WEP MUST be enable when security is set to shared / 802.1X radius security mode. 4.
Configure wireless LAN MAC filter Description: Enable, disable and configure the wireless LAN MAC filter feature. This feature enables the router to allow or deny connection from wireless client based on the MAC address. Synopsis: wlan macfilter [--mode ] [--add ] [--remove ] Options: --mode Description: Disable and set the wireless LAN MAC filter mode.
[--rmac3 ] [--rmac4 ] Options: --mode Description: configure wireless AP mode. Default value: ap --restrict Description: enable or disable bridge restrict mode.
> wlan info --config Wlan Config Info : Basic : wlan config enable = 1 wlan config hide = 0 wlan config ssid = Series7Wireless7890 wlan config bssid = 00:11:22:33:44:56 wlan config country = AU Advance : wlan config isolate = 0 wlan config band = b wlan config channel = 0 wlan config rate = 0 wlan config mrate = 0 wlan config brate = default wlan config rts = 2347 wlan config frag = 2346 wlan config dtim = 1 wlan config beacon = 100 wlan config xpress = off wlan config gmode = auto wlan config gprotect = au
wlan security WepKeyBit = 128 wlan security WepKey2 = wlan security WepKey3 = wlan security WepCurrentKeyindex = 1 --macfilter Description: display the list of parameters from macfilter option Example: > wlan info --macfilter Wlan macfilter Info : wlan macfilter mode = disabled wlan macfilter entry : --wds Description: display the list of parameters from wds opiton Example: > wlan info --wds Wlan wds Info : wlan wds mode = ap wlan wds restrict mode = disabled --station Description: display the list of authe
• • • • none: disable the service. local: enable the service at LAN side only remote: enable the service at WAN side only both: enable the service at both LAN and WAN sides. (2) To add an entry of IP range that to be enable to manage the gateway. Subnet mask of 255.255.255.255 is for a host with the specific IP address. Synopsis: remoteaccess iprange --add • • • • none: forbid the IP range to manage the 3G10WV.
config AP mode. Default value : ap --restrict config bridge restrict mode. Default value : disabled --rmac1 --rmac2 --rmac3 --rmac4 config remote bridge MAC address NOTE 4: You should enable the option - “restrict” before setting any restrict MAC address (setting --rmac1~4) or your restrict MAC address setting will be ignored. After the version – C40_R01, the wireless driver – 3.91.15.
--macfilter list parameters of macfilter command --wds list parameters of wds command --station list authenticated wireless stations and their status NOTE 5: You can use this command to view your wireless settings; no matter the settings are modified from web or CLI, the command will show the latest information for you. Example 5: After example 4, if we forgot our ssid, we can view the ssid with the following command. wlan info --config --help: Display usage for WLAN interface.
3G10WV HSPA Wi-Fi Router with Voice – 95
Contact Information If you have any technical difficulties with your product, please do not hesitate to contact NetComm’s Customer Support Department. Email: support@netcomm.com.au www.netcomm.com.au Note: NetComm Technical Support for this product only covers the basic installation and features outlined in the Quick Start Guide. For further information regarding the advanced features of this product, please refer to the configuring sections in the User Guide or contact a Network Specialist.
