Installation Owner's manual

ManualsBrandsNordson ASYMTEK ManualsEquipmentDispenseMate 585

DispenseMate

583 Dispensing System

DispenseMate

585 Dispensing System

DispenseMate 580 Series Installation Guide

The DispenseMate 580 Series Dispensing System (D-580) brings new dispensing power to a compact package.

The D-580 Series platform utilizes the same dispense control technology as some of Asymtek’s most advanced

Dispensing Systems. Two models of the DispenseMate Dispensing Systems are available with different size

dispensing areas, the D-583 and D-585 Dispensing Systems. Refer to the DispenseMate 580 Series User Guide

for additional information on each system.

The D-580 Series Dispensing Systems are designed to sit on top of a standard height (800 mm or 30-inch) work

bench; however work benches vary in stability and strength. The stability of the work bench will directly influence

the dispensing results. For best results, the use of an optional welded machine base (Asymtek P/N 193418) is

recommended.

The Dispensing System utilizes Asymtek’s Fluidmove

for Windows XP (FmXP) software, the same industry-

proven software package used on all Asymtek Dispensing Systems. FmXP and DispenseMate’s flexible

architecture makes it easy for customers to upgrade as needed, and provides the portability to develop programs

offline that can be transferred to other sites or moved to inline systems. CAD Import software and Automatic

Pattern Recognition are also available.

Front View Features

Valve Pressure

Gauge/Regulator

Camera

Light Emitter

Vacuum Purge Cup

(optional)

Fluid Air

Connector

(clear)

Valve Air

Connector

(black)

Cooling Air

Connector

(green)

Tactile Sensor

(optional)

EMO Button

Off Button

On Button

ESD Grounding Strap

Connector

Precision Fluid

Gauge/Regulator

Vacuum Control

Summary of content (8 pages)

PAGE 1
DispenseMate® 583 Dispensing System DispenseMate® 585 Dispensing System DispenseMate 580 Series Installation Guide The DispenseMate 580 Series Dispensing System (D-580) brings new dispensing power to a compact package. The D-580 Series platform utilizes the same dispense control technology as some of Asymtek’s most advanced Dispensing Systems. Two models of the DispenseMate Dispensing Systems are available with different size dispensing areas, the D-583 and D-585 Dispensing Systems.
PAGE 2
RS232 Port Main Power Circuit Breaker DIP Configuration Switches Main Power Inlet Discrete I/O General Purpose Output Connector Main Air Inlet General Purpose Input Connector Interlock Rear View Features Dispensing Valve Configuration Valve Air Connection Fluid Pressure Connection Cooling Air Connection DJ-9000/DJ-2100 DispenseJet® Series Black fitting Clear fitting Green fitting DV-7000/DV-8000 Heli-Flow® Pumps N/A Clear fitting DV-01 N/A Clear fitting DV-07 Black fitting Clear fittin
PAGE 3
Safety Uncrate and Place the Dispensing System 1 • Installation procedures should only be performed by a trained service technician. • Before performing any of the System installation procedures in this guide, please review the Safety section presented in the DispenseMate 580 Series User Guide. • Disconnect and place a warning tag on the Main Power Inlet before performing maintenance or service.
PAGE 4
Install the Computer 2 1. Locate the Laptop Computer, remove all packaging material, and place it in the desired location. 2. Connect the USB 2.0 Cable (P/N 7209541) to the USB Type B connector at the right, rear of the DispenseMate and to the USB port on the Computer. 3. If the unit is furnished with the Advanced Dispensing Package, connect the RJ-45 Ethernet cable (P/N 7209539) between the laptop and the left, rear Ethernet connection on the Dispenser. 4.
PAGE 5
Install the Dispensing Valve 4 Prior to installing the Dispensing Valve, loosen (do not remove) the four (4) screws on the Z-axis face plate and slide the face plate up so that it is flush with the Z-axis extrusion. Tighten the screws on the face plate. To install the Dispensing Valve, slide the dovetail bracket (included with the Dispensing Valve) into the Valve Mounting Bracket on the Z-axis face plate. Secure by tightening the quick release lever on the Valve Mounting Bracket.
PAGE 6
Pneumatic Connections 6 Connect the air supply to the ¼-inch NPT quick-disconnect fitting at the facility air connection. Refer to the Specifications section of the DispenseMate 580 Series User Guide for additional information on System specifications. To connect Facility Air Supply: 1. Attach a quick-disconnect air fitting (customer supplied) to the facility air hose. 2. Connect the facility air hose to the Main Air Pressure Regulator Inlet. 3.
PAGE 7
System Power-Up 8 If necessary, refer to Front View Features in this guide to identify Dispensing System components. 1. Verify that the Main Power Cable is connected to the Main Power Inlet and the facility power source. 2. Verify that the facility air is at the recommended pressure level and connected to the Main Air Pressure Regulator Inlet. Refer to the DispenseMate 580 Series User Guide for additional information. 3.
PAGE 8
Asymtek Headquarters 2762 Loker Avenue West Carlsbad, CA 92010-6603 USA Tel: (760) 431-1919 1-800-ASYMTEK (1-800-279-6835) P/N 7212882, Revision A ©2007