Manual

I-2 Index
I
ID Systems
configuration .............................................................. 2-7
Idle Timers ............................................................. 4-32, 5-6
Importing Images .......................................................... 5-33
Installation ............................................................... 2-1–2-3
Inverter
configuration ............................................................ 4-19
L
Light Beacon
configuration ............................................................ 4-21
beacon indicatorsettings ...................................... 4-24
log trigger fault.................................................... 4-21
Subsystem ........................................................... 4-22
Log Configuration ........................................................ 4-34
Log Files ....................................................................... 4-34
Log Trigger Fault .......................................................... 4-21
M
Macro Programs.............................................................. 5-2
creating .................................................................... 5-15
opening ...................................................................... 5-3
Main Pattern ................................................................... 5-3
Maintenance Manager .......................................... 4-37–4-39
adding procedures .................................................... 4-39
deleting procedures .................................................. 4-39
Maintenance Procedure ................................................. 5-28
creating .................................................................... 5-28
Mask Regions ................................................................. 5-4
coating inside a mask region ...................................... 5-4
creating .................................................................... 5-25
inherited mask regions ............................................... 5-4
Material Characterization ............................................... 4-8
N
Needle Finder
configuration ............................................................ 4-29
tolerances ................................................................. 4-30
O
Operator Screen ....................................................... 3-2–3-6
buttons ....................................................................... 3-5
menu bar .................................................................... 3-6
variable monitor ......................................................... 3-4
P
Pattern Array ................................................................. 5-43
Patterns ........................................................................... 5-3
creating .................................................................... 5-16
inserting instructions ................................................ 5-18
main pattern ............................................................... 5-3
placing...................................................................... 5-29
Periodic Procedures ........................................................ 5-5
Periodic Timers ............................................................. 4-32
Pneumatic Regulators and Gauges
fluid air pressure ...................................................... 3-15
Printing ......................................................................... 5-32
Procedures ....................................................................... 5-4
begin idle .................................................................... 5-6
calling ....................................................................... 5-30
creating ..................................................................... 5-26
end idle ................................................................ 5-6, 5-7
periodic ....................................................................... 5-5
reserved ...................................................................... 5-4
Product Frame ................................................................. 5-9
Product Map
new group ................................................................. 4-36
new part .................................................................... 4-36
Product Map Configuration .................................. 4-35–4-39
Product Programs
creating ..................................................................... 5-11
opening ....................................................................... 5-2
Production Configuration ..................................... 4-32–4-34
Program Instruction
Abort ......................................................................... B-1
Add Fault ................................................................... B-1
Arc Coat .................................................................... B-1
Arc Coat - Center Radius .......................................... B-2
Area Coat .................................................................. B-3
Call Procedure ........................................................... B-4
Check Needle ............................................................ B-5
Coat ........................................................................... B-5
Comment ................................................................... B-6
Else ............................................................................ B-6
End ............................................................................ B-6
End Flow Measurement ............................................. B-7
Fan Quick Check ....................................................... B-7
Fan Width .................................................................. B-8
Fiducial ...................................................................... B-8
Find Home ................................................................. B-9
Find Needle ............................................................... B-9
If ............................................................................ B-10
Log Message ........................................................... B-10
Move Relative ......................................................... B-10
Move Tool ............................................................... B-11
Pattern Array ........................................................... B-11
Pause ....................................................................... B-11
P
lace Pattern ............................................................ B-12
Position Verify ........................................................ B-12
Prompted Log .......................................................... B-12
Repeat ...................................................................... B-13
Rotate Home ............................................................ B-13
Rotate Tool .............................................................. B-13
SC-400 Control ....................................................... B-14
Send ACL to Conveyor ........................................... B-14
Send ACL to Robot ................................................. B-14
Set Acceleration ...................................................... B-14
Set Outputs .............................................................. B-15
Set Velocity ............................................................. B-15
Spot ......................................................................... B-15
Terminate Program .................................................. B-16
Tilt Tool .................................................................. B-16
Wait ......................................................................... B-16
While ....................................................................... B-17
Programming
advanced concepts .................................................... 5-43
calling procedures ..................................................... 5-30
creating macro programs .......................................... 5-15
creating mask regions ............................................... 5-25
creating product programs ............................... 5-11–5-14
editing programs ....................................................... 5-31
inserting pattern instructions .................................... 5-18