Introduction Thank you for purchasing this NORITZ CONNECT NWC-ADAPTER (this product). This product is used for remote operation, setup and monitoring Noritz heater by Smart Devices. Noritz America reserves the right to discontinue, or change at any time, the designs and/or specifications of its products without notice. When there are any changes in this Owner’s Guide (this manual) due to version updates of any functions of this product, download this manual from http://support.noritz.com/.
Contents Important Safety Information .............................................................. 4 Product Overview ................................................................................ 7 System Diagram.................................................................................. 7 Product Limitations.............................................................................. 7 How to open the front cover................................................................ 7 General Parts...
Important Safety Information - 1 Important Safety information Refer to the Owner’s Guide of the heater before using this product. To prevent damage to property and injury to the user, the icons shown below will be used to warn of varying levels of danger. Every indication is critical to the safe operation of this product and must be understood and observed. Potential dangers from accidents during installation and use are divided into the following two categories.
CAUTION Do not splash water with hose etc on this product. This product can be installed outdoors, however install the product in a location to avoid direct rain or severe wind. When installing outdoors the wireless signal strength may be weak and/or unstable. Do not expose this product to steam. Do not locate this product near stoves or ovens, this may cause damage or failure. Do not use parts other than those specified for this product. Do not look straight an LED when a front cover is opened.
Important Safety Information - 2 ■ Canada Regulatory Information This device complies with Industry Canada’s Licence-Exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules.
Product Overview System Diagram An overview of the NORITZ CONNECT System is below. NWC-ADAPTER Wireless LAN Internet Wireless router Remote Cord Server LTE, Wireless LAN Smartphone Tablet Unit (Heater) Remote Controller Product Limitations • This product is not compatible with WEP encryption method. ( page 21). • This product operates only in the 2.4 GHz frequency band. It is not compatible with the 5GHz frequency band.
General Parts 䐡㻌 䐟 Front Inside the Front Cover 䐣 䐦 䐧 䐤 䐨 䐥 䐟 䐢 䐠 Inside Name ① Status LED (RED) ② Plastic Cover ③ Instruction Sheet ④ Product information sticker ⑤ Dip Switches ⑥ RESET Button ⑦ MODE Button ⑧ WPS Button ⑨ AP Button Description Displays current system status. ( page 9) Product information, labels, protection of Circuit Board. Indicates each button operation and LEDs condition. Indicates Model, Serial Number(S/N), SSID, Key and MAC. To enable or disable functions.
Description of each LED condition Status LED Unit, Router, Server LED Four LEDs show current system status. There are three display modes: Normal, Settings and Signal Strength Check Mode. Description of each LED condition LED condition Description During Normal condition Status （RED） ON The system is normal. Blinking When there is an error somewhere in the system. ( Unit （RED） ON Connected to the unit. OFF While checking connection with the unit. Blinking Lost connection with the unit.
How to Use ■ Button Operations Connection Methods Activate WPS Mode To activate the WPS Mode, press and hold the MODE button for 3 seconds or more to connect this product to the wireless router. During WPS Mode, all LEDs will blink 5 times. To deactivate the setting, press and hold the WPS button for 3 seconds or more or leave it for 2 minutes. Press and hold 3 seconds or more Activate AP Mode To activate the AP Mode, press and hold the AP button for 3 seconds or more.
Status LED brightness settings The brightness can be changed to 3 different levels when pressing the MODE button. Low -> Medium(default) -> High -> Low Set to your desired brightness. * Do not look directly at Status LED. Reset (Reboot) Use this if this product does not operate correctly. note) This product keeps current settings. 1. Press and hold the RESET button for 5 seconds or more, all LEDs turn OFF. 2. All LEDs turn ON and this product starts the connection to "Unit", "Router" and "Server".
Before setting up this product Pre-installation Checklist Internet connection Check the internet connection is available. Noritz heater Noritz heater compatibility with this product. If you are not sure which heaters are compatible, refer to the Noritz website shown below for a list of approved Noritz heaters. *This product cannot be connected to heaters made by other companies. Wireless LAN access point Wireless router for connecting this product.
Setting up this product - 1 ■ Setup procedure To set up this product for use, do steps 1 through 4 below. 1st step : Account registration 2nd step : Register the heater 3rd step : Pair the product to your smartphone 4th step : Add the product to your network (wireless router) * NORITZ CONNECT App functions and screens are subject to change without prior notice. 1st step 1 2 Account registration To register your account, start the App and tap "Don't have account? Sign up".
Setting up this product - 2 2nd step 1 Register the heater To register your heater to your account, tap either "Add a heater" or "Scan QR Code". 1-1 1-2 Select a registration method Add a heater Scan QR Code 1-1 [Register your heater manually] Tap the "Add a heater". Follow the directions on the screen and enter the "Model Name" and "Serial Number", then tap "Submit Data". 1-2 [Register your heater automatically] Tap the "Scan QR Code". Scan the QR code is shown on the rating plate of the heater.
2 If you have not finished the heater warranty registration, the screen switches to the Warranty Registration screen. Follow the directions and enter the required information. Check all the information is correct, then tap "Submit Warranty". Warranty information is used for user information of this product. * Registered warranty information cannot be changed after registration is complete.
Setting up this product - 3 3rd step Pair the product to your smartphone * From step 3, you will need to operate this product's button. Check the Status LED is lit (ON) or blinking. ( page 9) Open the front cover. ( page 7) Notification If the Status LED is not lit, this product is not receiving power. Before using this product, check the heater's power supply is on. This product has no power button.
4th step 1 Add the product to your network (wireless router) Connect this product to the wireless router. Select either "WPS Method Setup" or "Manual Router Setup" and then connect to the router. "WPS Method Setup" can be utilized if your wireless router has a "WPS" button. Refer to your wireless router's manual for more information.
Setting up this product - 4 This product's WPS mode starts and all of this product's LEDs (Status, Unit, Router, and Server LEDs) blink 5 times. After the LEDs blink 5 times, tap "Next". Wait for the unit to come online. WPS Method Setup Connecting Check!! If you cannot connect using "WPS Method Setup", try connecting by "Manual Router Setup". 1-2 [Manual Router Setup] Skip to 2 if you have already successfully connected using "1-1 [WPS Method Setup]".
4. Enter the Password of the wireless router, and then tap "Connect". 5. Connecting. Check!! If the router you want to connect to does not appear on the list, relocate this product or wireless router closer to increase the signal strength. The following items are common to both "WPS Method Setup" and "Manual Router Setup". 2 Displays network connection status. • If the connection was successful, tap "Done". The display goes to the NORITZ CONNECT home screen.
Setting up this product - 5 Check!! If the connection was unsuccessful, check the following items, and then try again "3rd step: Pair the product to your smartphone". • Is the wireless router WPS function activated? Solution: Check the wireless router user's manual and then operate the wireless router's "WPS" button. • Is the signal strength sufficiently strong? Solution: Move the wireless router closer and then establish a connection. 3 The NORITZ CONNECT home screen appears.
Appendix - 1 ■ Specifications Model Name NWC-ADAPTER (NAW-1 US) Wireless communication method Compatible with IEEE802.11b/g/n (2.4 GHz), 1 - 11ch. Setup Method WPS method / Manual setup method Function AP (Access Point) function Voltage 15VDC Power consumption 1W or less Temperature Settings Range 14 to 122°F (-10°C to 50°C) Avoid areas with direct sunlight, rainwater and water. Dimensions (Height)×(Width)×(Depth) 7.52" (191.0mm)×4.83"(122.6mm)×1.18"(30.0mm) Weight 0.
Appendix - 2 ■ Troubleshooting Please check • Check the heater power is on. None of the LEDs are lit. • Check this product and heater are correctly connected with the remote cord. The Unit LED is blinking (RED). • Check the heater is operating correctly. Contact the installer if it is not operating. • Check the settings of the wireless router. The Router LED is blinking (YELLOW). The Server LED is blinking (GREEN).
■ Trademarks The names of products and services mentioned in this manual are trademarks or registered trademarks of their respective companies. Company trademarks and registered trademarks ・ "AndroidTM", and "Google PlayTM" are trademarks of Google Inc. ・ "App Store" is a service mark of Apple Inc. ・ "iOS®" is a trademark or registered trademark of Apple Inc. in the United States and other countries. ・ "iPhone®" is a trademark or registered trademark of Apple Inc. in the United States and other countries.
Noritz America Corporation Limited Warranty Noritz Connect Wireless Adapter Pursuant to the terms and conditions set forth in this Limited Warranty (this "Warranty"), Noritz America Corporation ("Noritz") hereby warrants to the original consumer purchaser, in the originally installed location, (the "Owner") the enclosed wireless adaptor (the "Product") to be free from any material defects in materials and workmanship.
Limitations of Liability Please refer to the Installation Manual and Owner's Guide supplied with your new Noritz product. This warranty becomes null and void if any of the following are determined to be contributing factors to failure of the product under this warranty: 1. 2. 3. 4.
NOT WITHSTANDING ANYTHING IN THIS WARRANTY TO THE CONTRARY, EXCEPT FOR NORITZ' AFFIRMATIVE OBLIGATIONS EXPRESSLY SET FORTH IN THIS WARRANTY, NORITZ DISCLAIMS ANY AND ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, REGARDING THE PRODUCT AND ITS FUNCTIONALITY, PERFORMANCE, MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE OR INTELLECTUAL PROPERTY RIGHTS.
Installation Company Information Company Name Address City Zip Code Installer Name License Number Phone Fax Place of Purchase 27
