User's Manual

ManualsBrandsNortek Security & Control ManualsElectronics500 Series Z-Wave Outlet

Removing Associations

To remove the Associations, if the Hub has recognized the Associations, refer to the Z-Wave

Hub’s instructions on how to remove Associations. If the Hub has not recognized the Associations,

removing the WO15EMZ5-1 from the Z-Wave network will eliminate the Associations.

ADVANCED OPERATION

All On/All Off

The WO15EMZ5-1 supports the ALL ON / ALL OFF commands. The WO15EMZ5-1 can be set

to respond to ALL ON and ALL OFF commands four different ways.

Refer to your Controller for information on how to set the WO15EMZ5-1 to operate in the manner

you desire. Some Controllers may be only able to set certain settings of ALL ON/ALL OFF

response.

The four different ways the WO15EMZ5-1 can be setup to respond to ALL ON and ALL OFF

commands are:

1. Responds to ALL ON or the ALL OFF command.

2. Responds to ALL OFF command but will not respond to ALL ON command.

3. Responds to ALL ON command but will not respond to ALL OFF command.

4. Responds to ALL ON and the ALL OFF command.

CONFIGURATION

The WO15EMZ5-1 supports the Conﬁ guration command. Each unit can be conﬁ gured to

operate slightly differently than how it works when you ﬁ rst install it.

Using the Conﬁ guration command you can conﬁ gure the following:

Night Light

By default, the LED on the WO15EMZ5-1 will turn OFF when the load attached is turned ON.

To make the LED turn ON when the load attached is turned ON, set Parameter 3 to a value of 1.

Parameter Length Valid Values Conﬁ guration Option

1 Byte

LED OFF when the load is on, and ON when the load

is off (default mode)

LED ON when the load is on, and OFF when the

load is off

2 LED is always on

3 LED is always off

LED blinks during RF transmissions from or to the

device

Energy Monitoring

WO15EMZ5-1 reports the total accumulated Kilowatt Hours (kWh) and the instantaneous Watts

being consumed by the Z-Wave controlled outlet. The always powered outlet is merely a pass-

thru and energy consumed by loads plugged into it are not measured.

Parameter Length Valid Values Conﬁ guration Option

1 Byte

Automatic reporting OFF

1-255

Number of minutes between automatic reporting

(Default = 6)

Conﬁ guration Parameter 13 conﬁ gures the rate at which the energy readings are reported. If

the maximum kWh value that can be reported is reached (21,474 kWh), then it will remain at the

maximum level until reset to 0.

The Watts reading provides the immediate reading of the power being consumed by the load.

The Watts reading takes several seconds to settle so wait a few seconds before reading the

energy value when the state of the switch (on / off) has changed.

To reset, the total accumulated kWh used by the WO15EMZ5-1 the Z-Wave controller needs

to send a reset command at the request of the user. It will also be reset if the WO15EMZ5-1 is

excluded from the Z-Wave network.

Over-The-Air (OTA) Update

A Quadruple tap of the switch enables the ﬁ rmware update mode. Firmware update mode

must be entered before the system Controller sends the ﬁ rmware update command to begin

downloading new ﬁ rmware. Firmware update mode is enabled for 60 seconds after the

quadruple tap. If the Firmware update does not begin before the end of the 60 seconds then

ﬁ rmware update mode is exited returns to normal operation. The LED “winks” twice per second

indicating it is in ﬁ rmware update mode.

Resetting to Defaults

Each conﬁ guration Parameter can be set back to its default setting by setting the default bit

in the Conﬁ guration Set command. See your Controller’s instructions on how to do this

(and if it supports it). All conﬁ guration commands will be reset to their default state when the

WO15EMZ5-1 is excluded from the Z-Wave network by using the Controller to reset the node.

SPECIFICATIONS

Power: 120 VAC, 60 Hz

Signal (Frequency): 908.42 MHz / 916 MHz

Maximum Load: Resistive: 15 amps (1800 watts) maximum, 120 VAC

Range: Up to 130 feet line of sight

Z-Wave

and Z-Wave Plus

are registered trademarks of Sigma Designs

and its subsidiaries in the United States and other countries.

REGULATORY INFORMATION

The WO15EMZ5-1 is certiﬁ ed to comply with applicable FCC and IC rules and regulations governing RF and EMI

emissions.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any interference received, including interference

that may cause undesired operation.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician to help.

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment

IC Notice

This Class B digital apparatus complies with Canadian ICES-003

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Le présent appareil est conforme

aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

WARRANTY

What is Covered?

Nortek Security & Control (“NS&C”) warrants to consumers who purchase this product for personal, family or

household purposes new from NS&C directly or from an authorized NS&C dealer, that the product will be free from

defects in materials and workmanship for a period of (1) year from the date of purchase. This warranty only applies if

the product is installed at a residence in the 50 United States or District of Columbia, and only at the site of the original

installation. It is not transferable. This warranty is not extended to resellers.

If a defect exists, NS&C will have you ship the defective part or product to us and we will, at our option, either repair or replace it.

This warranty does not cover the cost of labor to remove a defective part or product or to reinstall any repaired or replacement

part or product

This warranty does not cover defects or damages caused by improper handling, maintenance, storage, installation, removal

or re-installation, misuse, non-factory authorized modiﬁ cation or alteration, use of incompatible accessories, electrical power

problems or surges, impact by foreign objects, accident, ﬁ re, acts of God, normal wear and tear or shipping damage other than

a shipment from NS&C. Note that all NS&C products are designed to be installed, removed and serviced by trained individuals

or professionals.

Keep your original sales receipt as it will be required to obtain warranty service.

This warranty shall not be extended or restarted upon receipt of any repaired or replacement part or product under this warranty.

No person is authorized to extend or otherwise modify this warranty.

How do I Obtain Warranty Service?

To obtain warranty service, email our Returns Department at returns@nortek.com. Include your name, address, telephone

number, the model number of your product, a copy of your original sales receipt, and a description of the problem. Unless we

need to discuss the situation further with you, you will be emailed a Return Authorization Number and shipping instructions.

If we need to discuss the situation further with you, we will call or email you. NS&C may require troubleshooting on installed

product before a Return Authorization Number is issued. Anything shipped to us without a Return Authorization Number will be

automatically returned unopened. You are responsible for the charges for shipment to us, unless you are a California resident.

Limitations

THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXCEED THE WARRANTY PERIOD PROVIDED HEREIN.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not

apply to you.

NS&C SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM

THE BREACH OF ANY WRITTEN OR IMPLIED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

This warranty gives you speciﬁ c legal rights, and you may also have other legal rights which vary from State to State.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,WO15EMZ5-1,GO CONTROL; P/N: 10010070 BX1; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 2 OF 2