Installation Guide

What happens when your CO Alarm detects Carbon Monoxide?
When the CO Alarm detects potentially dangerous levels of CO, if ashes the red
alarm light immediately and then sounds a loud alarm if the CO persists. Table 2
shows how the CO Alarm reacts to different levels of CO gas and exposure time. At
higher levels of CO gas and exposure time. At higher levels of CO the Alarm turns
on sooner. The rate of ashing of the red light indicates the level of CO. If your CO
Alarm sounds follow the instructions in the “What to do when the Alarm Sounds”
section of this manual.
WARNING: NEVER IGNORE THE ALARM!
Red Light
(Pre-Alarm)
Sounder
(Alarm)
CO Gas Level
0<ppm<30 ppm Off* Off
> 50 ppm
1 ash
every 3 secs
on within 60 - 240 min
(typical 90 min)
> 110 ppm
2 ashes
every 3 secs
on within 10 - 50 min
(typical 30 min)
>250 ppm
3 ashes
every 3 secs
on within 4 - 15 min
(typical 9 min)
How to Tamper Proof the Alarm
The 2GIG-CO8E-345 alarm can be made tamper proof. Break off the small pillar
on the base of the CO Alarm (Figure 7). This will allow the tamper catch release
to be activated and in the position shown in Figure 8. To remove Alarm from wall
or ceiling it is now necessary to use a small at tool (See Figure 9) to release the
catch release. Follow the procedure for removing the alarm that is shown in Figure
10. If necessary it is possible to further tamper proof the Alarm by using a #2 or
#4 1/4 inch self tapping screw (not included) and installing it into the indent of the
mounting base (Figure 11).
PILLAR
FLAT BLADE
TOOL
Select a wall or ceiling location for the CO Alarm.
Screw CO Alarm mounting base to wall or ceiling.
Another alternative, if desired, is to allow the CO Alarm to free stand on a at
surface with the mounting base attached (See Figure 4).
If locating the CO Alarm in a room with a fuel burning appliance:
• If it is mounted on a wall, it should be located at a height greater than the
height of any door or window but still be at least 6 inches from the ceiling.
• If it is mounted on the ceiling it should be at least 12 feet from any wall or
light tting.
• The CO Alarm should be a horizontal distance of between 3 feet and 9 feet
from the potential CO source.
• If there is a partition in the room, the CO Alarm should be located on the
same side of the partition as the potential source.
• In rooms with sloped ceilings, the CO Alarm should be located at the high
side of the room.
If locating the CO Alarm in a bedroom or in rooms remote from a
fuel burning appliance:
• Mount the CO Alarm relatively close to the breathing zone of the occupants.
Whatever position is chosen make sure it is possible to view the three light
indicators, when in the vicinity of the Alarm.
WARNING: Do not use the CO Alarm on an intermittent basis, or as a portable
detector for the leakage of combustion products from fuel burning appliances or
chimneys.
Test the CO Alarm weekly by pressing and holding the test button for a few seconds.
Replace Alarm when the “REPLACE UNIT BY” date has been reached. Check the
label on the side of the Alarm.
Do not t Alarm until all building work is completed to avoid contamination.
Installation of CO Alarm/Wall or Ceiling Mounting
Rotate CO alarm COUNTER CLOCKWISE to remove it from mounting plate.
Placement of CO Alarm
Ideally a Carbon Monoxide Alarm should be installed in:
• Every room containing a fuel burning appliance.
• Remote rooms where occupants spend a considerable amount of time.
• Every bedroom.
However if the number of Carbon Monoxide Alarms to be tted is limited, the
following points should be considered when deciding where best to t the alarm(s):
• If there is an appliance in a room where people sleep, place a CO Alarm in
this room.
• Locate a CO Alarm in a room containing a ueless or open-ued appliance,
Locate an Alarm in a room where the occupant(s) spend most of their time
(e.g. sitting room).
• In a bedsite, the CO Alarm should be placed as far away from the cooking
appliance as possible, but near to where the person sleeps.
• If the appliance is in a room not normally used, such as a boiler room, the CO
Alarm should be placed just outside the room so that the Alarm will be heard
more easily.
Suggested Alarm locations are shown in Figure 3.
Verify that the package includes the following:
• 1―Wireless CO Alarm and Mounting Plate
• 2―Plastic wall anchors
• 2―Phillips Screws
• 3―AAA batteries (installed). Replace only with Duracell MN2400 Alkaline
AAA size batteries (obtainable from local retailer).
TEST
&
HUSH
ALARM
FAULT
POWER
CARBON
MONOXIDE
ALARM
CO ALARM
CO ALARM
MOUNTING BASE
ANCHORS (2)
SCREWS (2)
Installation Tools Required
• Phillips Screw Driver
• Variable Speed Drill with 1/16” Drill Bit
• Flat Blade Tool (optional)
CO Alarm Description and Function
A. ALARM: Red LED
B. FAULT: Amber LED
C. POWER: Green LED
D. Test/Hush Buon
GENERAL INFORMATION
The Carbon Monoxide Alarm (2GIG-CO8E-345) is a battery powered wireless
device for detecting the dangerous levels of Carbon Monoxide. It is one of the
e-Series devices from Nortek Security and Control providing enhanced security
with encrypted communications to the control panel using the 345Mhz frequency.
The intended use is with compatible 2GIG wireless alarm systems.
To know the maximum number of transmitters that can be supported, see the
appropriate 2GIG Security System Installation Guide.
IMPORTANT: This CO Alarm must be tested and maintained regularly following
NFPA 720 requirements. This device is designed to protect individuals from the
acute effects of carbon monoxide exposure. It will not fully safeguard individuals
with specic medical conditions. If in doubt, consult a medical practitioner. It is
intended for use in ordinary indoor locations of family living units. It is not designed
to measure compliance with Occupational Safety and Health Administration
(OSHA) commercial or industrial standards.
ALARM
FAULT
POWER
TEST
&
HUSH
CARBON
MONOXIDE
ALARM
A
B
C
D
What is Carbon Monoxide?
Many people are killed each year, and many more suffer ill health from Carbon
Monoxide (CO) poisoning. CO is an invisible, odorless, tasteless and extremely
toxic gas. It is produced by appliances and vehicles burning fuels, such as coal, oil,
natural/bottled gas, parafn, wood, petrol, diesel, charcoal etc. CO is absorbed by
red blood cells in the lungs in preference to oxygen - this results in rapid damage to
the heart and brain from oxygen starvation.
High levels of CO in a house can be caused by:
• Incorrectly or poorly installed fuel-burning appliances.
• Blocked or cracked chimneys/ues.
• Blocked vents or draft-proong which makes areas with fuel burning
appliances or replaces airtight.
• Engines of cars, lawnmowers etc. left running in conned spaces.
• Portable parafn or gas heaters in badly ventilated rooms.
See Table 1 for Symptoms from Carbon Monoxide Poisoning.
Symptoms of Carbon Monoxide Poisoning
CO Parts per Million (ppm)
Inhalation Time (approx.) & Symptoms Developed
35ppm
The maximum allowable concentration for continuous exposure
in any 8 hr. period according to Occupation Safety & Health
Association
150ppm
Slight headache after 1 1/2 hours
200ppm Slight headache, fatigue, dizziness, nausea after 2-3 hours
400ppm
Frontal headache within 1-2 hours, life threatening after 3 hours,
also maximum ppm in ue gas (on air free basis) according to
US Environmental Protection Agency
800ppm
Dizziness, nausea and convulsions within 45 minutes.
Unconsciousness within 2 hours. Death within 2-3 hours
1.600ppm
Headache, dizziness and nausea within 20 minutes. Death
within (1) one hour
3,200ppm
Headache, dizziness and nausea within 5-10 minutes. Death
within 25-30 minutes
6,400ppm
Headaches, dizziness and nausea within 1-2 minutes. Death
within 10-15 minutes
12,800ppm
Death within (3) three minutes
Bedroom
Bedroom Bedroom
Kitchen
Living
Room
Basement
Garage
Closed
Doors
To
Bed
rooms
(Gas Furnace)
CO ALARM LOCATIONS
CO ALARM
TIGHTEN
SCREWS TO
SECURELY HOLD CO
ALARM MOUNTING
BASE IN PLACE
SIDE VIEW
SIDE VIEW
FREE STANDING
CO ALARM MOUNTING
OPTION
Unsuitable Locations for CO Alarms
Do not place the CO Alarm in any of the following areas:
1. In the immediate vicinity of a cooking appliance (keep it at least 3 feet
horizontally from it).
2. Outside the building.
3. In an enclosed space (e. g. in or below a cupboard).
4. In a damp or humid area.
5. Directly above a sink or cooker.
6. Next to a door, window, air vent or anywhere that it would be affected by
drafts.
7. Next to an extractor fan.
8. Over heat sources such as radiators or hot air vents.
9. Where it would be obstructed, e.g. by curtains or furniture.
10. In an area where the temperature could drop below -15°F or rise above 105°F.
11. Where dirt or dust could block the sensor.
12. Where it could be easily knocked or damaged, or where it could be accidentally
turned off or removed.
13. In a bathroom or other areas where the CO Alarm may be exposed to water
splashes, dripping or condensation (e.g. above an electric kettle).
14. Near paint, thinners, solvent fumes or air fresheners.
TEST
&
HUSH
ALARM
FAULT
POWER
CO ALARM
WALL INSTALLATION
OF CO ALARM USING
SCREWS & ANCHORS
OR
MAX.
FROM CEILING
FLOOR LINE
6"
MIN.
FROM FLOOR
10"
CO ALARM
MOUNTING BASE
TEST
&
HUSH
ALARM
FAULT
POWER
CEILING INSTALLATION
OF CO ALARM
FROM WALL
12"
[30cm]
12"
[30cm]
CO ALARM
CO ALARM
MOUNTING BASE
TAMPER CATCH RELEASE IN ACTIVAT E POSITION AFTER
BREAKING OFF PILLAR
TAMPER CATCH RELEASE IN DEACTIVAT E POSITION
USING FLAT TOOL TO PRY TOWARD WALL
ALARM
FAULT
POWER
ROTATE CO ALARM COUNTERCLOCKWISE
ON BASE UNTIL MARKS ON SIDE ALIGN
MARKS NEED
TO ALIGN
PRY TAMPER CATCH RELEASE
AT THE SAME TIME TOWARD WALL
CO ALARM
BASE
1/4 inch SELF TAPPING SCREW
INDENT
MOUNTING
BASE
CO ALARM
ALARM
FAULT
POWER
TEST
&
HUSH
CARBON
MONOXIDE
ALARM
Ei207
CO ALARM
CO ALARM MOUNTING BASE
ROTATE CO ALARM CLOCKWISE TO LOCK ON MOUNTING BASE
AND TEST
6. Ceiling Installation of CO Alarm
Figure 8 Tamper Catch in ACTIVATE position.
Figure 9. Tamper Catch in DEACTIVATE position.
Figure 10. Tamper DEACTIVATION Procedure
Figure 11. Tamper Option Using Screw to Fasten Mounting Base to Alarm
Figure 12. Tesng the CO Alarm
Figure 5. Wall Installation of CO Alarm
Figure 1. Box Contents
Figure 2. Alarm Top View
Figure 4. Mounting Options for CO Alarm and Mounting Base
Figure 3 Alarm Locations
Figure 7. Breaking Off Tamper proof Pillar
2GIG-CO8E-345
CARBON MONOXIDE ALARM WITH ENHANCED SECURITY
1
2
3
4
5
6 7
8
9
10
11
12
13
14
15
Table 2. CO Alarm Response
Table 1. Carbon Monoxide Symptoms
PRINTER’S INSTRUCTIONS:
MANUAL,2GIG-CO8E-345 - P/N 10023355 B - INK: BLACK - MATERIAL: 16 LB. MEAD BOND - SIZE: 16.000" X 18.000"- TOL. +/- 0.125"- SCALE:1:1 - FOLDING: FOLD 4 X TO FINAL SIZE 4.000"X 4.500"- FINISH WITH LOGO SHOWING - SIDE 1 OF 2
NOTE: Individuals with medical problems may consider using warning devices
which provide audible and visual signals for carbon monoxide concentrations
under 30 ppm.